PX700HD/PG700WU PG705HD/PG705WU DLP Projector User Guide IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service.
Compliance Information FCC Statement This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. "" "' 13. "; Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this unit near water. Clean with a soft, dry cloth. Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions.
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Substance Proposed Maximum Concentration Actual Concentration Lead (Pb) 0.1% < 0.
Copyright Information Copyright © ViewSonic® Corporation, 2018. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association.
Table of contents Important safety instructions .......................2 Controlling the projector through a LAN environment (PG705HD/PG705WU) ........................................................... 37 Using the projector in standby mode. 44 Adjusting the sound ........................... 44 Shutting down the projector .............. 45 Menu operation.................................. 46 Introduction......................5 Projector features ................................. 5 Shipping contents.......
Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product. Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Please read this manual before you operate your projector. Save it for future reference. Do not look straight at the projector lens during operation.
13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire. - Do not place this projector on a blanket, bedding or any other soft surface. - Do not cover this projector with a cloth or any other item. - Do not place inflammables near the projector. 14. Always place the projector on a level, horizontal surface during operation.
will perform the secondary role of restraining the projector should its attachment to the mounting bracket become loose.
Introduction Projector features The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use. Some of the features may not be available on your projector. Actual performance may vary and subject to model specifications. • • • • • • • • • • • • • • • • • Power saving function decreasing the power consumption of the lamp by up to 70% when no input signal can be detected for a set period of time.
Controls and functions Projector Temperature indicator light Lamp indicator light Power indicator light Focus ring Vent (heated air exhaust) Zoom ring Projection lens • Power Toggles the projector between standby mode and Power ON. • (Help) Displays the HELP menu with a long press for 3 seconds. • / (Keystone keys) Manually corrects distorted images resulting from an angled projection. • Blank Hides the screen picture.
1 2 3 4 5 6 7 11 12 PX700HD/PG700WU AUDIO IN HDMI 1 HDMI 2 USB 5V/1.5A Out MINI USB COMPUTER IN MONITOR OUT AUDIO OUT RS-232 1 2 3 4 5 6 7 8 9 10 11 12 PG705HD/PG705WU Kensington anti-theft lock slot AC power cord inlet Adjuster foot Security bar for anti-theft lock slot Ceiling mount holes Adjuster foot 1. 2. 3. 4. 5. 6. HDMI 1 HDMI port. HDMI 2 HDMI port. USB 5V/1.5A Out USB Type A port for power supply. MINI USB Mini USB port.
Remote control PX700HD/PG700WU PG705HD/PG705WU To use the remote mouse control keys (Page Up, Page Down), see "Using the remote PgUp/PgDn function" on page 10 for details. Some functions may not be available on some models. The following functions are not available for this projector: horizontal keystone and 4 corner adjustment. • Auto Sync Automatically determines the best picture timings for the displayed image. • Source Displays the source selection bar.
• Left/ Right/ Up/ Down • Selects the desired menu items and makes adjustments. (Presentation Timer) Displays the presentation timer settings menu. • Menu Turns on the On-Screen Display (OSD) menu. • Eco Mode Displays the lamp mode selection bar. • Exit Exits and saves menu settings. • (Volume Up) Increases the volume level. • (Laser) Emits visible laser pointer light for presentation purposes. • (Volume Down) Decreases the volume level. • • Aspect Displays the aspect ratio selection bar.
If different codes are set on the projector and remote control, there will be no response from the remote control. When that happens, a message will display to remind you to switch the code for the remote control. Using the remote PgUp/PgDn function The capability of operating your computer with the remote control gives you more flexibility when delivering presentations. 1. 2. 3. Set the input signal to a PC signal.
• Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for your region. • Never throw the batteries into a fire. There may be danger of an explosion. • If the batteries are drained or if you will not be using the remote control for an extended period of time, remove the batteries to avoid damage to the remote control from possible battery leakage.
Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment. Your projector is designed to be installed in one of the following possible installation locations: 1.
Projection dimensions The "screen" mentioned below refers to the projection screen usually consisting of a screen surface and a support structure. Please see "Projector specifications" on page 78 for the native display resolution of this projector.
PG705HD 16:9 image on a 4:3 Screen (a) Screen Size (b) Projection distance min. (d) Vertical offset (c) Image height max. min. max. inch mm inch mm inch mm inch mm inch mm inch mm 60 1524 71 1791 85 2150 27 686 1.4 34 1.4 34 70 1778 82 2090 95 2421 32 800 1.6 40 1.6 40 80 2032 94 2388 109 2767 36 914 1.8 46 1.8 46 90 2286 106 2687 123 3113 41 1029 2.0 51 2.0 51 100 2540 118 2986 136 3459 45 1143 2.3 57 2.
PX700HD 16:9 image on a 4:3 Screen (a) Screen Size (b) Projection distance min. max. (d) Vertical offset (c) Image height min. max. inch mm inch mm inch mm inch mm inch mm inch mm 60 1524 72 1832 79 2015 27 686 1.4 34 1.4 34 70 1778 84 2137 93 2351 32 800 1.6 40 1.6 40 80 2032 96 2443 106 2687 36 914 1.8 46 1.8 46 90 2286 108 2748 119 3023 41 1029 2 51 2 51 100 2540 120 3053 132 3358 45 1143 2.3 57 2.
PG705WU 16:10 image on a 16:10 Screen (a) Screen Size (b) Projection distance min. (d) Vertical offset (c) Image height max. min. max.
PG700WU 16:10 image on a 16:10 Screen (a) Screen Size (b) Projection distance min. (d) Vertical offset (c) Image height max. min. max.
There is 3% tolerance among these numbers due to optical component variations. It is recommended that if you intend to permanently install the projector, you should physically test the projection size and distance using the actual projector in situ before you permanently install it, so as to make allowance for this projector's optical characteristics. This will help you determine the exact mounting position so that it best suits your installation location.
Connection When connecting a signal source to the projector, be sure to: 1. 2. 3. Turn all equipment off before making any connections. Use the correct signal cables for each source. Ensure the cables are firmly inserted. In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 5). They are commercially available from electronics stores. The connection illustrations below are for reference only.
Connecting a computer or monitor Connecting a computer 1. 2. 3. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer. Connect the other end of the VGA cable to the COMPUTER IN signal input socket on the projector. If you wish to use the remote mouse control function, take a USB cable and connect the larger end to the USB port of the computer, and smaller end to the MINI USB socket on the projector. See "Using the remote PgUp/PgDn function" on page 10 for details.
If no HDMI source is available, the next best video signal is Component video (not to be confused with composite video). Digital TV tuner and DVD players output Component video natively, so if available on your devices, this should be your connection method of choice in preference to (composite) video. See "Connecting a Component Video source device" on page 21 for how to connect the projector to a component video device.
If the selected video image is not displayed after the projector is turned on and the correct video source has been selected, check that the Video source device is turned on and operating correctly. Also check that the signal cables have been connected correctly. Connecting an S-Video source device Examine your Video source device to determine if it has an unused S-Video output socket available: • • 1. 2. If so, you can continue with this procedure.
Operation Starting up the projector 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). 2. Press Power to start the projector. As soon as the lamp lights up, a "Power On Ring Tone" will be heard. The Power indicator light stays blue when the projector is on. (If necessary) Rotate the focus ring to adjust the image clearness.
Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. The OSD screenshots below are for reference only, and may differ from the actual design. Below is the overview of the OSD menu. Main menu icon Highlight Status Sub-menu Go to the previous page or to exit. Current input signal To use the OSD menus, please select your language first. 1. Press Menu to turn the OSD menu on. 3. Press to highlight Language and press Enter. 2.
Utilizing the password function For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on page 24. You will be inconvenienced if you enable the password function yet forget the password somehow. Do make a note of your password, and keep the note in a safe place for later recall.
Entering the password recall procedure 1. 2. 3. Press and hold Auto Sync on the remote control for 3 seconds. The projector will display a coded number on the screen. Write down the number and turn off your projector. Seek help from the local service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector. The "XXX" shown in the above screenshot are numbers that vary depending on different projector models.
Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. Be sure the Quick Auto Search function in the SYSTEM menu is On if you want the projector to automatically search for the signals. You can also manually select the desired signal by pressing one of the source selection keys on the remote control, or cycle through the available input signals. 1. 2. Press Source. A source selection bar is displayed.
Adjusting the projected image Adjusting the projection angle The projector is equipped with an adjuster foot. It changes the image height and vertical projection angle. Screw the adjuster foot to fine tune the angle until the image is positioned where you want it. If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 28 for details.
3. Press to correct keystoning at the top of the image or press keystoning at the bottom of the image. to correct Magnifying and searching for details If you need to find the details on the projected picture, magnify the picture. Use the direction arrow keys for navigating the picture. • 1. 2. 3. Using the remote control Press on the remote control repeatedly to magnify the picture to a desired size. Press the directional arrows ( , , , ) to navigate the picture.
5. Panorama: Scales the image proportionally to fit the projector's native resolution in its vertical height and fills the screen in a non-linear manner. 6. 2.35:1: Scales an image so that it is displayed in the center of the screen with a 2.35:1 aspect ratio without aspect alteration. 7. Anamorphic: Scales a 2.35:1 aspect image so that it fills the screen. The table below demonstrates the effects of the aspect ratio settings on projectors with different native resolutions.
• • Press Color Mode to display the selection bar and press / to select a desired mode or press Color Mode repeatedly. Go to the IMAGE > Color Mode menu and press Enter. Press / to select a desired mode. Picture modes for different types of signals The picture modes available for different types of signals are listed below. 1. 2. 3. 4. 5. 6. 7. Brightest mode: Maximizes the brightness of the projected image.
Go to the IMAGE > Advanced > Color menu and press / . Lower setting produces less saturated colors. If the setting is too high, colors on the image will be overpowering, which makes the image unrealistic. This function is only available when the input signal is Video, YPbPr or YCbCr. Adjusting Tint Go to the IMAGE > Advanced > Tint menu and press / . The higher the value, the more greenish the picture becomes. The lower the value, the more reddish the picture becomes.
1. 2. 3. Go to the IMAGE > Color Temp. menu and press Enter. Press / to select Cool, Normal or Warm and press Enter. Press / to highlight the item you want to change and adjust the values by pressing / . • Red Gain/Green Gain/Blue Gain: Adjusts the contrast levels of Red, Green, and Blue. • Red Offset/Green Offset/Blue Offset: Adjusts the brightness levels of Red, Green, and Blue. This function is only available for PC timings from a VGA or HDMI input signal.
7. 8. Repeat steps 3 to 6 for other color adjustments. Make sure you have made all of the desired adjustments. Setting the presentation timer Presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function: • Using the remote control 1. Press on the remote control and press repeatedly or / to select a Timer Period. Press Enter or wait for 3 seconds to activate the timer.
To cancel the timer, perform the following steps: 1. 2. 3. Press on the remote control or go to the BASIC > Presentation Timer menu. Highlight Off. Press Enter. A confirmation message displays. Highlight Yes and press Enter to confirm. You will see the message “Timer is Off” displaying on the screen. Hiding the image In order to draw the audience's full attention to the presenter, you can press Blank on the projector or remote control to hide the screen image.
To activate the High Altitude Mode: 1. Open the OSD menu and go to the SYSTEM > High Altitude Mode menu. 2. Press Enter and press / to select On. A confirmation message is displayed. 3. Highlight Yes and press Enter. Operation under "High Altitude Mode" may cause a higher decibel operating noise level because of increased fan speed necessary to improve overall system cooling and performance.
If you discover the inversion of the 3D image depth, set the 3D Sync Invert function to “Invert” to correct the problem. Controlling the projector through a LAN environment (PG705HD/PG705WU) The projector supports Crestron® software. With correct settings for the LAN Control Settings menu, you can manage the projector from a computer using a web browser when the computer and the projector are properly connected to the same local area network.
5. 6. 7. Press / to move the cursor and the press / to enter the value. You can also use the numeric buttons on the remote control to enter the value. To save the settings, press Enter. If you do not want to save the settings, press Exit. Press to highlight Apply and press Enter. If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server settings will display 0.0.0.0.
controllers of AMX connected to the same network. For the Details of AMX Device Discovery, visit the AMX web site at http://www.amx.com/. 4. If your projector is connected to a network which supports Simple Mail Transfer Protocol (SMTP), you can configure it to alert you via email on significant events. 5. The Crestron (e-Control) page displays the Crestron e-Control user interface. See "About Crestron e-Control®" on page 41 for details.
Please pay attention to the limitation of input length (including space and other punctuation keys) in the list blow: Category Item Network Input Length Maximum Number of Characters DHCP/Manual (N/A) IP Address XXX.XXX.XXX.XXX Subnet Mask XXX.XXX.XXX.XXX Gateway XXX.XXX.XXX.XXX DNS Server XXX.XXX.XXX.XXX AMX device discovery (N/A) Network Settings Password SNMP Email Setting SMTP Setting Email Alert Alert Condition / > < $ % + \ ' " are prohibited.
About Crestron e-Control® 1. The Crestron e-Control® page provides a variety of virtual keys to control the projector or adjust the projected pictures. i ii i You can press / to reveal more buttons. i i. These buttons function the same as the ones on the OSD menus or remote control. See "2. IMAGE menu" on page 51 and "Projector" on page 6 for details. ii. To switch between input signals, click on your desired signal.
iii. You can adjust the LAN Control Settings. iv. Once set, access to the remote network operation on this projector has been password-protected. v. Once set, access to the tools page has been password-protected. To prevent errors, only input the English alphabet and digits on the tools page. After making the adjustments, press the Send button and the data will be saved for the projector. vi. Press Exit to go back to the remote network operation page.
3. The info page displays the information and status of this projector. Press Exit to go back to the remote network operation page. 4. After pressing the button “Contact IT Help”, the HELP DESK window will appear in the upper right corner of the screen. You will be able to deliver messages to RoomView™ software administrators/users who connect to the same local area network. For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
Using the projector in standby mode Some of the projector functions are available in standby mode (plugged in but not turned on). To use these functions, be sure the cable connections are correctly made. For the connection methods, see the Connection chapter. Active VGA Out Selecting On in the POWER MANAGEMENT > Standby Settings > Active VGA Out outputs a VGA signal when the Computer 1 and Monitor Out sockets are correctly connected to devices. The projector outputs the signal received only from Computer 1.
Shutting down the projector 1. Press Power or Off and a confirmation message is displayed prompting you. If you don't respond in a few seconds, the message will disappear. 2. 3. Press Power or Off a second time. Once the cooling process finishes, a "Power Off Ring Tone" will be heard. Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time. To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 44 for details.
Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible. Main menu Sub-menu Options Screen Color Off/Whiteboard/Blackboard/Greenboard PG705HD/PX700HD: Auto/4:3/16:9/ Panorama/2.35:1/Anamorphic PG705WU/PG700WU: Auto/4:3/16:10/ Panorama/2.
Main menu Sub-menu Signal Auto Power On CEC Direct Power On Auto Power Off Smart Energy 3. POWER MANAGEMENT Standby Settings Sleep Timer Power Saving Active VGA Out Active Audio Out Smart Restart Quick Power Off Mute Audio Volume Audio Settings Power On/Off Ring Tone Timer Period Timer Display Presentation Timer 4.
Main menu Sub-menu 3D Settings HDMI Settings 5.
Main menu • • • • 7.
Description of each menu Function Description Screen Color See "Using Screen Color" on page 31 for details. Aspect Ratio See "Selecting the aspect ratio" on page 29 for details. Keystone Position See "Correcting keystone" on page 28 for details. Displays the position adjustment page. To move the projected image, use the directional arrow keys. The values shown on the lower position of the page change with every key press you made until they reach their maximum or minimum.
Function Description Color Mode See "Selecting a picture mode" on page 30 for details. Brightness See "Adjusting Brightness" on page 31 for details. Contrast See "Adjusting Contrast" on page 31 for details. Color Temp. 2. IMAGE menu See "Selecting a Color Temperature" on page 32 and "Setting a preferred color temperature" on page 32 for details. Color See "Adjusting Color" on page 31 for details. Tint See "Adjusting Tint" on page 32 for details.
Function Auto Power On Description Signal Selecting VGA/HDMI allows the projector to turn on automatically once the VGA/HDMI signal is fed through the VGA/HDMI cable. You can also select All and the projector will turn on automatically upon receiving either a VGA or HDMI signal. CEC See "Using the CEC function" on page 36 for details. Direct Power On Selecting On allows the projector to turn on automatically once the power is fed through the power cord.
Function Description 4. BASIC menu Audio Settings See "Adjusting the sound" on page 44 for details. Presentation Timer See "Setting the presentation timer" on page 34 for details. Pattern The projector can display several test patterns. It helps you adjust the image size and focus and check that the projected image is free from distortion. Blank Timer See "Hiding the image" on page 35 for details.
Function Description Closed Caption Enable Activates the function by selecting On when the selected input signal carries closed captions. • 5. ADVANCED menu Closed Caption (PG705HD/ PG705WU) Captions: An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked as "CC" in TV listings). This function is only available when a Composite video input signal is selected and its system format is NTSC.
Function Description Source Shows the current signal source. Color Mode Shows the selected mode in the IMAGE menu. Resolution Shows the native resolution of the input signal. 7. INFORMATION menu Color System Shows input system format. IP Address (PG705HD/PG705WU) Shows the IP address of your projector. MAC Address (PG705HD/PG705WU) Shows the MAC Address of your projector. MAC Address stands for Media Access Control Address, which is a physical layer address used to uniquely identify a network node.
Maintenance Care of the projector You need to keep the lens and/or filter (optional accessory) clean on a regular basis. Never remove any parts of the projector. Contact your dealer when any part of the projector needs replacing. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface. • • Use a canister of compressed air to remove dust. If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface.
• If your projector is ceiling-mounted or is not easily accessible, pay special attention to your personal safety when replacing the dust filter. Installing the dust filter 1. 2. 3. Be sure to turn off the projector and unplug it from power source. As the arrows shown to the right, fit the filter by aligning and inserting it into the projector slots. Tighten the screw the secures the dust filter. 2 1 3 For first time installation: 4. Open the OSD menu and go to the ADVANCED > Filter Settings menu. 5.
CAUTION Remember to set Filter Mode to Off in the ADVANCED > Filter Settings menu when using the projector with the dust filter removed. Setting Filter Mode to Off does not reset the filter timer. The timer will continue counting the next time you fit the filter back on and set Filter Mode to On. Lamp information Getting to know the lamp hour When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. To obtain the lamp hour information: 1.
Setting Sleep Timer This function allows the projector to turn off automatically after a set period of time to prevent unnecessary waste of lamp life. 1. Open the OSD menu and go to the POWER MANAGEMENT > Smart Energy menu. 2. Press Enter and the Smart Energy page is displayed. 3. Highlight Sleep Timer and press / . 4. If the preset time lengths are not suitable for your presentation, select Disable. The projector will not automatically shut down in a certain time period.
Indicators Light Status & Description Power events Blue Flashing Off Off Stand-by mode Blue Off Off Blue Off Off Powering up Normal operation Blue Flashing Off Off Normal power-down cooling (3 sec) Downloading Burn in off Red Off Off Blue Blue Blue Lamp events Blue Flashing Off Red First Lamp-Lit error cooling (60 sec) Off Off Red Blue Off Red Lamp error in normal operation (30 sec) CW start fail (30 sec) Thermal events Off Red Off Off Red Red Off Red Blue Off Red
Troubleshooting The projector does not turn on. Cause Remedy There is no power from the power cord. Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on. Attempting to turn the projector on again during the cooling process. Wait until the cooling down process has completed. No picture Cause Remedy The video source is not turned on or connected correctly.
Specifications Dimensions 332 mm (W) x 121 mm (H) x 261 mm (D) (Excluding extrusions) 332 261 121 66.34 86.93 Unit: mm Ceiling mount installation 199.55 Ceiling mount screws: M4 x 8 (Max. L = 8 mm) 63.62 60.87 198.
IR control table Key Format Byte1 Byte2 Byte3 Byte4 PgDn NEC X3 F4 05 FA PgUp NEC X3 F4 06 F9 Blank NEC X3 F4 07 F8 Auto sync NEC X3 F4 08 F7 Up NEC X3 F4 0B F4 Down NEC X3 F4 0C F3 Left NEC X3 F4 0E F1 Right NEC X3 F4 0F F0 Color Mode NEC X3 F4 10 EF Enter NEC X3 F4 15 EA Exit NEC X3 F4 28 D7 D.
Address code Code 1 83F4 Code 2 93F4 Code 3 A3F4 Code 4 B3F4 Code 5 C3F4 Code 6 D3F4 Code 7 E3F4 Code 8 F3F4 RS232 command table Pin Description Pin 1 NC 2 Description RX 3 TX 4 NC 5 GND 6 NC 7 RTSZ 8 CTSZ 9 NC RS-232 protocol Baud Rate 115200 bps (default) Data Length 8 bit Parity Check None Stop Bit 1 bit Flow Control None 64
Function Status Action cmd Turn on 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D Turn off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E Write Power Read Power status (on/off) 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 0x5E Reset all settings Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F Reset Color Settings Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2A 0x00 0x87 Splash Screen Black 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x0A 0x00 0x67 Splash
Message Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x00 0x84 Message On 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x01 0x85 Write Message Read Message status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x27 0x85 Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F Rear Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60 Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61 Write Projector Position Read pro
Write Aspect ratio Read Auto Adjust Aspect ratio Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62 Aspect ratio 4:3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64 Aspect ratio 16:9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65 Aspect ratio 16:10 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66 Aspect ratio Anamorphic 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x05 0x67 Aspect ratio 2.
Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68 Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69 Keystone status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A 0x69 Brightest 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69 Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A Photo 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x13 0x7C Standard 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x04 0x6D Presentation 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x14 0x7D Sports 0x06
Freeze on 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60 Freeze off 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x00 0x5F Write Freeze Read Freeze status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00 0x60 Input source VGA 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60 Input source HDMI 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x03 0x63 Input source HDMI2 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x07 0x67 Input source Composite 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65 Input source
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A 0x06 0x14 0x
Write HDMI Format Read Write HDMI Range Read RGB 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x00 0x85 YUV 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x01 0x86 Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x02 0x87 HDMI Format status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x28 0x86 Enhanced 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x00 0x86 Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x01 0x87 Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x02 0x88 HDMI Range status 0x07 0x14 0x00 0x05 0x00
code 1 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x00 0xA0 code 2 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x01 0xA1 code 3 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x02 0xA2 code 4 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x03 0xA3 code 5 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x04 0xA4 code 6 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x05 0xA5 code 7 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x06 0xA6 code 8 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x07 0xA7 Remote Control code status 0x07 0x14 0x
Remote Key Write Menu 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0F 0x61 Exit 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x13 0x65 Up 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0B 0x5D Down 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0C 0x5E Left 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0D 0x5F Right 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0E 0x60 Source 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x04 0x56 Enter 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x15 0x67 Auto 0x02 0x14 0x00 0x04 0x00 0x34
Timing chart Analog RGB Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) VGA 640 x 480 4:3 60/72/75/85 SVGA 800 x 600 4:3 60/72/75/85 1024 x 768 4:3 60/70/75/85 1152 x 864 4:3 75 1280 x 768 15:9 60 1280 x 800 16:10 60/75/85 1360 x 768 16:9 60 Quad-VGA 1280 x 960 4:3 60/85 SXGA 1280 x 1024 5:4 60 WXGA 1366 x 768 16:9 59.
HDMI Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) VGA 640 x 480 4:3 60 SVGA 800 x 600 4:3 60 XGA 1024 x 768 4:3 60 1280 x 768 15:9 60 1280 x 800 16:10 60 1360 x 768 16:9 60 Quad-VGA 1280 x 960 4:3 60 SXGA 1280 x 1024 5:4 60 WXGA 1366 x 768 16:9 59.
3D (HDMI signal included) Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) SVGA 800 x 600 4:3 60* / 120** XGA 1024 x 768 4:3 60* / 120** HD 1280 x 720 16:9 50* / 60* / 120** WXGA 1280 x 800 16:9 60* / 120** HDTV (1080p) 1920 x 1080 16:9 60* WUXGA 1920 x 1200 16:10 60* Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) SDTV (480i)*** 720 x 480 4:3 / 16:9 60 for Video Signal * 50Hz and 60Hz signals are supported for Side-by-Side, Top-Bottom, and Frame Sequentia
Component video (PG705HD/PG705WU) Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) HDTV (1080p) 1920 x 1080 16:9 50 / 60 HDTV (1080i) 1920 x 1080 16:9 50 / 60 HDTV (720p) 1280 x 720 16:9 50 / 60 SDTV (480p) 720 x 480 4:3 / 16:9 60 SDTV (576p) 720 x 576 4:3 / 16:9 50 SDTV (480i) 720 x 480 4:3 / 16:9 60 SDTV (576i) 720 x 576 4:3 / 16:9 50 Composite video (PG705HD/PG705WU) Signal Aspect Ratio Refresh Rate (Hz) NTSC 4:3 60 PAL 4:3 50 PAL60 4:3 60 SECAM 4:3 50
Projector specifications All specifications are subject to change without notice. Not all models can be purchased in your region. Model name PG705WU PG705HD PX700HD PG700WU Product Specification Resolution Throw ratio Display system Lamp Type 0.48” WUXGA (1920 x 1200) 1.47~1.76 (87”±3%@ 2.75m) 0.48” WUXGA (1920 x 1200) 1.5~1.65 (87”±3%@ 2.81m) 0.47” 1080p (1920 x 1080) 1.47~1.76 1.5~1.65 (95”±3%@ (95”±3%@ 3.09m) 3.
Operating Altitude 0–1499 m at 5°C–35°C 1500–3000 m at 5°C–25°C Operating Relative Humidity 10%–90% (without condensation) 79
Copyright information Copyright Copyright © 2018. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation.
Customer Support For technical support or product service, see the table below or contact your reseller. Note : You will need the product serial number. Website T= Telephone C = CHAT ONLINE Email www.viewsonic.com.au AUS= 1800 880 818 NZ= 0800 008 822 service@au.viewsonic.com Canada www.viewsonic.com T= 1-866-463-4775 service.ca@viewsonic.com Europe www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/ Hong Kong www.hk.viewsonic.com T= 852 3102 2900 service@hk.viewsonic.
Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
How to get service: 1. For information about receiving service under warranty, contact ViewSonic Customer Support (please refer to “Customer Support” page). You will need to provide your product’s serial number. 2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product. 3.
Mexico Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components & accessories.
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico: Name, address, of manufacturer and importers: México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004 Hermosillo: Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col. Bugambilias C.