PJD5132/PJD5232L/PJD5134/ PJD5234L/PJD5533w DLP Projector User Guide IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http://www.viewsonic.
Compliance Information FCC Statement This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this unit near water. 6. Clean with a soft, dry cloth. 7. Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat. 9.
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/ EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Substance Proposed Maximum Concentration Actual Concentration Lead (Pb) 0.1% < 0.
Copyright Information Copyright © ViewSonic® Corporation, 2013. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association.
Table of contents Using the projector in standby mode. 38 Shutting down the projector .............. 39 Menu operation.................................. 40 Important safety instructions .......................2 Introduction......................4 Maintenance ...................50 Projector features ................................. 4 Shipping contents................................. 5 Projector exterior view......................... 6 Controls and functions .........................
Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product. Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Please read this manual before you operate your projector. Save it for future reference. Do not look straight at the projector lens during operation.
13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire. - Do not place this projector on a blanket, bedding or any other soft surface. - Do not cover this projector with a cloth or any other item. - Do not place inflammables near the projector. 14. Always place the projector on a level, horizontal surface during operation.
Introduction Projector features The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use. The projector offers the following features.
Shipping contents Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. Standard accessories The supplied accessories will be suitable for your region, and may differ from those illustrated. Projector Power Cord VGA Cable Multi-language user manual DVD Quick Start Guide Remote Control & Batteries Optional accessories 1. 2. 3.
Projector exterior view 1. Front/upper side 1 6 2 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 3 4 5 7 Rear/lower side 12. PJD5132/PJD5232L 8 9 11 12 13 14 15 16 18 17 13. 14. 15. 16. 17. 18. External control panel (See "Projector" on page 7 for details.
Controls and functions Projector 1 2 3 4 5 3 6 1. 2. 3. 4. 5. Focus ring Adjusts the focus of the projected image. Zoom ring Adjusts the size of the image. Keystone/Arrow keys ( / Up, / Down) Manually corrects distorted images resulting from an angled projection. Left/Blank Hides the screen picture. POWER indicator light Lights up or flashes when the projector is under operation. MENU EXIT 8. 9. 10. I I 6. 7. POWER Toggles the projector between standby mode and on.
Remote control 1 18 2 3 4 5 19 6 4 8 7 20 9 21 10 11 12 13 15 16 17 22 14 23 24 25 To use the remote mouse control keys (Page Up, Page Down, , and ), see "Using the remote mouse control" on page 10 for details. 6. 7. 1. 2. I I POWER Toggles the projector between standby mode and on. Source selection keys (VGA/Video) Selects an input source for display. VGA Selects D-Sub / Comp. 1 or D-Sub / Comp. 2 source for display. Video Selects Video source for display. 4. 5. 9.
12. Magnify Displays the zoom bar that magnifies or reduces the projected picture size. 13. Lock Activates or deactivates panel key lock. Freeze Freezes the projected image. Pattern Displays embedded test pattern. Blank Hides the screen picture. DynamicEco™ Decreases the power consumption of the lamp by up to 30%. 14. 15. 16. 17. 19. 20. 21. 22. 23. • It takes some time to initiate this function. Make sure the projector has been turned on for more than 4 minutes.
Using the remote mouse control The capability of operating your computer with the remote control gives you more flexibility when delivering presentations. 1. 2. Connect the projector to your PC or notebook with a USB cable prior to using the remote control in place of your computer’s mouse. See "Connecting a computer" on page 16 for details. Set the input signal to D-Sub / Comp. 1, D-Sub / Comp. 2 or HDMI. The HDMI input is only available on the PJD5134/PJD5234L/PJD5533w models. 3. 4.
Replacing the remote control batteries 1. 2. 3. To open the battery cover, turn the remote control over to view its back, push on the finger grip on the cover and slide it in the direction of the arrow as illustrated. The cover will slide off. Remove any existing batteries (if necessary) and install two AAA batteries observing the battery polarities as indicated in the base of the battery compartment. Positive (+) goes to positive and negative (-) goes to negative.
Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment. Your projector is designed to be installed in one of four possible installation locations: 1.
Projection dimensions Refer to "Dimensions" on page 60 for the center of lens dimensions of this projector before calculating the appropriate position.
PJD5533w • 16:10 image on a 16:10 screen (a) (b) (e) (a) (f) (d) (c) (c) (d) (f) (b) (e) • 16:10 image on a 4:3 screen (a) (b) (a) (e) (f) (d) (c) (c) (d) (f) (b) (e) (e): Screen (f): Center of lens 16:10 image on a 16:10 Screen 16:10 image on a 4:3 Screen (a) Screen (b) Projection distance (c) Image (d) Vertical (b) Projection distance (c) Image (d) Vertical Size [m (inch)] [m (inch)] height offset height offset [inch (m)] [cm (inch)] [cm (inch)] [cm (inch)] [cm (inch)] min. max.
Connection When connecting a signal source to the projector, be sure to: 1. 2. 3. • • • Turn all equipment off before making any connections. Use the correct signal cables for each source. Ensure the cables are firmly inserted. In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 5). They are commercially available from electronics stores. The connection illustrations below are for reference only.
Connecting a computer or monitor Connecting a computer The projector provides two VGA input sockets that allow you to connect them to both IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are connecting legacy version Macintosh computers. To connect the projector to a notebook or desktop computer: 1. 2. 3. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer.
Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets: • HDMI • Component Video • S-Video • Video (composite) You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality.
If you have a separate sound system, you will most likely want to connect the audio output of your Video source device to that sound system, instead of to the mono audio projector. Connecting an HDMI device You should use an HDMI cable when making connection between the projector and HDMI devices. To connect the projector to an HDMI device: 1. 2. Take an HDMI cable and connect one end to the HDMI output port of the video device. Connect the other end of the cable to the HDMI input port on the projector.
Connecting an S-Video source device Examine your Video source device to determine if it has an unused S-Video output socket available: • • If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an S-Video source device: 1. 2. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device.
Operation Starting up the projector 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). 2. Press II POWER on the projector or remote control to start the projector. The POWER indicator light stays blue when the projector is on. (If necessary) Rotate the focus ring to adjust the image clearness. • If the projector is still hot from previous activity, it will run the cooling fan for approximately 60 seconds before energizing the lamp.
Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. The OSD screenshots below are for reference only, and may differ from the actual design. Below is the overview of the OSD menu. Main menu icon Screen Color Aspect Ratio Keystone Position Phase Highlight Sub-menu Current input signal Off Auto Status ENTER 16 0 H. Size Zoom 3D Settings Color Management Analog RGB MENU Exit Go to the previous page or to exit.
Utilizing the password function For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on page 21. You will be inconvenienced if you activate the password functionality and subsequently forget the password.
Entering the password recall procedure 1. 2. 3. Press and hold AUTO on the projector or Auto RECALL PASSWORD Sync on the remote control for 3 seconds. The Please write down the recall code, and contact ViewSonic projector will display a coded number on the Customer Center. screen. Recall code: Write down the number and turn off your 0212 projector. MENU Exit Seek help from the local service center to decode the number.
Disabling the password function To disable password protection, go back to the SYSTEM SETTING: ADVANCED > Security Settings > Power On Lock menu after opening the OSD menu system. Select Off by pressing / . The message 'INPUT PASSWORD' is displayed. Enter the current password. • If the password is correct, the OSD menu returns to the Security Settings page with 'Off' shown in the row of Power On Lock. You will not have to enter the password next time you turn on the projector.
Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. Be sure the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals. You can also manually select the desired signal by pressing one of the source selection keys on the remote control, or cycle through the available input signals. 1. Press SOURCE on the projector or remote control.
3. • YUV: Sets the color space as YUV. • Auto: Sets the projector to detect the color space setting of input signal automatically. Press to highlight HDMI Range and press / to select a suitable HDMI color range according to the color range setting of the output device connected. • Enhanced: Sets the HDMI color range as 0 - 255. • Normal: Sets the HDMI color range as 15 - 235. • This function is only available when the HDMI input port is in use.
Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen. To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps. • Using the remote control Press / on the projector or remote control to display the Keystone correction page. Press to correct keystoning at the top of the image.
Selecting the aspect ratio The 'aspect ratio' is the ratio of the image width to the image height. Most analog TV and computers are in 4:3 ratio, and digital TV and DVDs are usually in 16:9 ratio. With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal. To change the projected image ratio (no matter what aspect the source is): • Using the remote control 1.
About the aspect ratio In the pictures below, the black portions are inactive areas and the white portions are active areas. OSD menus can be displayed on those unused black areas. 1. Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal width. This is suitable for the incoming image which is neither in 4:3 nor 16:9 and you want to make most use of the screen without altering the image's aspect ratio. 16:10 picture 15:9 picture 2. 3.
6. Anamorphic (PJD5132/PJD5134/PJD5232L/ PJD5234L only): Scales a 16:9 aspect image vertically and horizontally in a non-linear manner so that it fills the screen with a 4:3 aspect ratio.
Optimizing the image Selecting a picture mode The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type. To select an operation mode that suits your need, you can follow one of the following steps. • Press MODE/ENTER on the projector or Color Mode on the remote control repeatedly until your desired mode is selected. • Go to the PICTURE > Color Mode menu and press / to select a desired mode.
4. 5. Movie mode: Is suitable for enjoying dark movies or DVD movies best viewed in a blackened (little light) home cinema or lounge room environment. Dynamic Movie mode: Is suitable for enjoying dark movies or DVD movies best viewed in a blackened (little light) home cinema or lounge room environment. In addition, the projector will optimize the image quality using the dynamic Movie function in accordance with the projected contents. It takes some time to initiate this function.
Adjusting Brightness Highlight the PICTURE > Brightness menu and press / . The higher the value, the brighter the image. And the lower the setting, the darker the image. Adjust this control so the black areas of the image appear just as black and that detail in the dark areas is visible. +30 +50 +70 0 +30 Adjusting Contrast Highlight the PICTURE > Contrast menu and press / . The higher the value, the greater the contrast.
4. T4: Makes images appear reddish white. *About color temperatures: There are many different shades that are considered to be "white" for various purposes. One of the common methods of representing white color is known as the “color temperature”. A white color with a low color temperature appears to be reddish white. A white color with a high color temperature appears to have more blue in it.
Setting the presentation timer Presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function: 1. Press Timer on the remote control to access the Presentation Timer menu or go to the SYSTEM SETTING: ADVANCED > Presentation Timer menu and press MODE/ENTER to display the Presentation Timer page. 2. Highlight Timer Period and decide the time period by pressing / .
Hiding the image In order to draw the audience's full attention to the presenter, you can use on the projector or Blank on the remote control to hide the screen image. Press any key on the projector or remote control to restore the image. The word 'BLANK' appears at the lower right corner of the screen while the image is hidden.
To activate the High Altitude Mode: 1. Press MENU/EXIT on the projector or Menu on the remote control and then press / until the SYSTEM SETTING: ADVANCED menu is highlighted. 2. Press to highlight High Altitude Mode and Notice We recommend you use the High Altitude mode by selecting it whenever your environment is higher than 1500 m. Do you want to turn High Altitude Mode ON? Yes No press / to select On. A confirmation message is displayed. 3.
2. Press to highlight 3D Settings and press MODE/ENTER on the projector or Enter on the remote control. 3. Press to highlight 3D Sync and press MODE/ENTER on the projector or Enter on the remote control. 4. Press to select a 3D Sync setting according to the table below and then press MODE/ENTER on the projector or Enter on the remote control to confirm.
Active Audio Out Selecting On outputs an audio signal when the AUDIO IN and AUDIO OUT sockets are correctly connected to devices. Quick Power Off Selecting On enables the function and the projector will not enter the cooling process after being shut down. Selecting Off disables the function and the projector will enter normal cooling process after being shut down.
Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.
Main menu Sub-menu Options Quick Auto Search HDMI Format (PJD5134/PJD5234L/ PJD5533w only) HDMI Range (PJD5134/PJD5234L/ PJD5533w only) 4.
High Altitude Mode DCR Audio Settings Mute Volume 5 sec/10 sec/15 sec/20 sec/25 sec/30 sec Menu Settings Center/Top-Left/TopMenu Position Right/Bottom-Left/ Bottom-Right Closed Caption Enable On/Off Closed Caption Caption Version CC1/CC2/CC3/CC4 Lamp Mode Normal/Economic Lamp Settings Reset Lamp Timer Equivalent Lamp Hour Timer Period 1~240 minutes Always/1 min/2 min/3 min/ Timer Display Never Top-Left/Bottom-Left/TopTimer Position Right/Bottom-Right Presentation Timer Timer Counting Count Down/Count Up D
Main menu 6.
Description of each menu Function Screen Color Aspect Ratio Keystone 1. DISPLAY menu Position Description Corrects the projected picture’s color when the projection surface is not white. See "Using Screen Color" on page 32 for details. There are three options to set the image's aspect ratio depending on your input signal source. See "Selecting the aspect ratio" on page 28 for details. Corrects any keystoning of the image. See "Correcting keystone" on page 27 for details.
Function Color Mode Reference Mode Brightness 2. PICTURE menu Contrast Color Tint Description Pre-defined picture modes are provided so you can optimize your projector image set-up to suit your program type. See "Selecting a picture mode" on page 31 for details. Selects a picture mode that most suits your need for the image quality and further fine-tune the image based on the selections listed on the same page below. See "Setting the User 1/User 2 mode" on page 32 for details.
Function Quick Auto Search Description See "Switching input signal" on page 25 for details. HDMI Format See "Changing HDMI input settings" on page 25 for details. HDMI Range 3. SOURCE menu DynamicEco Timer Allows the projector to decrease the power consumption automatically if no input signal is detected after a set period of time. It takes some time to initiate this function. Make sure the projector has been turned on for more than 4 minutes.
Function Description Language Sets the language for the On-Screen Display (OSD) menus. See "Using the menus" on page 21 for details. The projector can be installed on a ceiling or behind a screen, or with one or more mirrors. See "Choosing a location" on page 12 for details. Allows the projector to turn off automatically if no input signal is detected after a set period of time. See "Setting Auto Power Off" on page 51 for details.
Function High Altitude Mode DCR Description A mode for operation in high altitude areas. See "Operating in a high altitude environment" on page 36 for details. Enables or disables the DCR (Dynamic Contrast Ratio) function. Selecting On enables the function and the projector will automatically switch the lamp mode between normal and economic modes according to the input image detected. This function is only available when a PC source is in use.
Function Description 5. SYSTEM SETTING: ADVANCED menu Presentation Timer Reminds the presenter to finish the presentation within a certain time frame. See "Setting the presentation timer" on page 35 for details. Security Settings See "Utilizing the password function" on page 22 for details. Remote Control Code See "Remote control code" on page 9 for details. Reset All Settings Returns all settings to the factory preset values.
Maintenance Care of the projector Your projector needs little maintenance. The only thing you need to do on a regular basis is to keep the lens clean. Never remove any parts of the projector except the lamp. Contact your dealer if other parts need replacing. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface. • • Use a canister of compressed air to remove dust.
Lamp information Getting to know the lamp hour When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. To obtain the lamp hour information: 1. Press MENU/EXIT on the projector or Menu on the remote control and then press / until the SYSTEM SETTING: ADVANCED menu is highlighted. 2. Press to highlight Lamp Settings and press MODE/ENTER on the projector or ENTER on the remote control. The Lamp Settings page is displayed. 3.
Timing of replacing the lamp When the LAMP indicator light lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. CAUTION The LAMP indicator light and TEMPerature indicator light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes.
Replacing the lamp To prepare a new lamp, contact your dealer and tell the lamp type number. Type number: RLC-078 (PJD5132/PJD5232L/PJD5134/PJD5234L) Type number: RLC-085 (PJD5533w) WARNING Hg - Lamp contains mercury. Manage in accordance with local disposal laws. See www.lamprecycle.org • Be careful of broken glass when replacing the lamp. • Please wear eye protection and gloves when performing overhead installation.
4. Loosen the screw that secures the lamp. 5. Disconnect the lamp’s wire connector from the projector, and then lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector. 2 1 CAUTION • Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector. • Do not place the lamp in locations where water might splash on it, children can reach it, or near flammable materials.
9. 10. 11. Place the lamp protection film supplied with the new lamp on the lamp compartment. Replace the lamp cover on the projector. Tighten the screws that secure the lamp cover. CAUTION • Loose screw may cause a bad connection, which could result in malfunction. • Do not over tighten the screws. 12. Restart the projector. CAUTION Do not turn the power on with the lamp cover removed. Resetting the lamp timer 13. 14. 15. 16. After the startup logo, open the On-Screen Display (OSD) menu.
Indicators Light POWER TEMP Status & Description LAMP Power events Blue Flashing Off Off Stand-by mode Blue Off Off Blue Off Off Powering up Normal operation Lamp events Purple Flashing Off Red Off Off Red The projector has shut down automatically. If you try to re-start the projector, it will shut down again. Please contact your dealer for assistance. 1. The projector needs 60 seconds to cool down. Or 2. Please contact your dealer for assistance.
Troubleshooting The projector does not turn on. Cause Remedy There is no power from the power cord. Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on. Attempting to turn the projector on again during the cooling process. Wait until the cooling down process has completed. No picture Cause Remedy The video source is not turned on or connected correctly.
Specifications Projector specifications • All specifications are subject to change without notice. • Not all models can be purchased in your region. General Product name DLP Projector Optical Resolution PJD5132/PJD5134: 800 x 600 SVGA PJD5232L/PJD5234L: 1024 x 768 XGA PJD5533w: 1280 x 800 WXGA 1-CHIP DMD 190 W lamp Display system Lamp Electrical Power supply Power consumption AC100–240V, 50/60 Hz (Automatic) 250 W (Max); < 0.5 W (Standby) Mechanical Weight 2.1 Kg (4.
Output terminal RGB output Audio signal output Speaker D-Sub 15-pin (female) x 1 PC audio jack x 1 2 watt x 1 Control terminal RS-232 serial control LAN USB serial control IR receiver 9 pin x 1 N/A Type mini B x 1 (Front) Environmental Requirements Operating temperature Operating relative humidity Operating altitude 0°C–40°C at sea level 10%–90% (without condensation) • • 0–1499 m at 5°C–35°C 1500–3000 m at 5°C–25°C (with High Altitude Mode on) 59
Dimensions 268 mm (W) x 84.4 mm (H) x 221 mm (D) (Excluding extrusions) 268 221 MENU EXIT 84.4 Ceiling mount installation Ceiling mount screws: M4 x 8 (Max. L = 8 mm) 81.5 81.5 110.
Timing chart Supported timing for PC input Resolution 720 x 400 640 x 480 800 x 600 1024 x 768 1280 x 800 1280 x 1024 1280 x 960 1400 x 1050 1600 x 1200 640 x 480@67Hz 832 x 624@75Hz 1152 x 870@75Hz Horizontal Frequency (kHz) Vertical Frequency (Hz) Pixel Frequency (MHz) Mode 31.469 31.469 37.861 37.5 43.269 61.91 35.156 37.879 48.077 46.875 53.674 30.99 77.425 48.363 56.476 60.023 68.667 39.634 98.958 49.702 62.795 71.554 63.981 79.976 91.146 60 65.317 75 35 49.722 68.68 70.087 59.94 72.
Supported timing for Component-YPbPr input Signal Format Horizontal Frequency (kHz) Vertical Frequency (Hz) 480i(525i)@60Hz 480p(525p)@60Hz 576i(625i)@50Hz 576p(625p)@50Hz 720p(750p)@60Hz 720p(750p)@50Hz 1080i(1125i)@60Hz 1080i(1125i)@50Hz 1080P@60Hz 1080P@50Hz 15.73 31.47 15.63 31.25 45.00 37.50 33.75 28.13 67.5 56.25 59.94 59.94 50.00 50.00 60.00 50.00 60.00 50.00 60 50 Displaying a 1080i(1125i)@60Hz or 1080i(1125i)@50Hz signal may result in slight image vibration.
Copyright information Copyright Copyright 2012. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation.
Appendix IR control table Code A Key Format Byte1 Byte2 Byte3 Byte4 Power NEC 83 F4 17 Auto Sync NEC 83 F4 08 E8 F7 VGA NEC 83 F4 41 BE AD Video NEC 83 F4 52 Source NEC 83 F4 04 FB Color Mode NEC 83 F4 10 EF Up / KeyS + NEC 83 F4 0B F4 Left NEC 83 F4 0E F1 Enter NEC 83 F4 15 EA Right NEC 83 F4 0F F0 Down / KeyS - NEC 83 F4 0C F3 Menu NEC 83 F4 30 CF My Button NEC 83 F4 56 A9 Exit NEC 83 F4 28 D7 Mouse L key NEC 83 F4 36
Code B Key Format Byte1 Byte2 Byte3 Byte4 Power NEC 83 F4 60 9F Auto Sync NEC 83 F4 63 9C VGA NEC 83 F4 64 9B Video NEC 83 F4 66 99 Source NEC 83 F4 7D 82 Color Mode NEC 83 F4 9E 61 Up / KeyS + NEC 83 F4 67 98 Left NEC 83 F4 69 96 Enter NEC 83 F4 6B 94 Right NEC 83 F4 6A 95 Down / KeyS - NEC 83 F4 68 97 Menu NEC 83 F4 6C 93 My Button NEC 83 F4 6D 92 Exit NEC 83 F4 6E 91 Mouse L key NEC 83 F4 38 C7 Mouse R key NEC 8
RS-232 protocol Baud Rate 115200 bps (default) Data Length 8 bit Parity Check None Stop Bit 1 bit Flow Control None Function Status Write Power Read Action cmd Turn on 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D Turn off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E Power status (on/off) 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 0x5E Reset Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F Reset Color Settings Execute 0x06
Projector Position Write Read 3D Sync Write Read Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F Rear Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60 Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61 Projector position status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00 0x5F OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 0x7E Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x01 0x7F Fra
Write Color temperature Read Blank Write Read KeystoneVertical Write Read Write Color mode Read Write Primary Color Read Hue Write Read Saturation Write Read Gain Write Read Freeze Write Read Color temperatureT1 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x00 0x66 Color temperatureT2 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x01 0x67 Color temperatureT3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x02 0x68 Color temperatureT4 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x08 0x03 0x69 Color temperat
Source input Write Read Quick Auto Search Write Read Write HDMI Format Read Write HDMI Range Read Mute Write Read Volume Input source VGA 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x00 0x60 Input source VGA2 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x08 0x68 Input source Composite 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x05 0x65 Input source SVIDEO 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x06 0x66 Input source HDMI 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0x03 0x63 Source 0x07 0x14 0x00
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A Language Wr
Customer Support For technical support or product service, see the table below or contact your reseller. Note : You will need the product serial number. Country/Region Website Australia/New Zealand www.viewsonic.com.au Canada Europe www.viewsonic.com www.viewsoniceurope. com www.hk.viewsonic.com www.in.viewsonic.com www.kr.viewsonic.com T = Telephone F = FAX AUS= 1800 880 818 NZ= 0800 008 822 T (Toll-Free)= 1-866-463-4775 T (Toll)= 1-424-233-2533 F= 1-909-468-3757 Email service@au.viewsonic.
Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
How to get service: 1. For information about receiving service under warranty, contact ViewSonic Customer Support (please refer to “Customer Support” page). You will need to provide your product’s serial number. 2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product. 3.
Mexico Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components & accessories.
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico: Name, address, of manufacturer and importers: México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004 Hermosillo: Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col. Bugambilias C.