PJD5155L/PJD5255L/ PJD5555LW/PJD5350LS/ PJD5550LWS DLP Projector User Guide IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http:// www.viewsonic.
Thank you for choosing ViewSonic With over 25 years as a world leading provider of visual solutions, ViewSonic is dedicated to exceeding the world’s expectations for technological evolution, innovation, and simplicity. At ViewSonic, we believe that our products have the potential to make a positive impact in the world, and we are confident that the ViewSonic product you have chosen will serve you well.
Compliance Information FCC Compliance Statement This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Substance Proposed Maximum Concentration Actual Concentration Lead (Pb) 0.1% < 0.
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this unit near water. 6. Clean with a soft, dry cloth. 7. Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat. 9.
Copyright Information Copyright © ViewSonic Corporation, 2014. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic and the three birds logo are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are trademarks of VESA.
Product Registration To fulfill possible future product needs, and to receive additional product information as it becomes available, please visit your region section on ViewSonic’s website to register your product online. The ViewSonic CD also provides an opportunity for you to print the product registration form. Upon completion, please mail or fax to a respective ViewSonic office. To find your registration form, use the directory “:\CD\Registration”.
Table of contents Introduction ........................................................................................... 1 Projector features ................................................................................................................................... 1 Package contents .................................................................................................................................. 2 Projector overview .................................................................
Introduction Projector features The projector integrates high-performance optical engine projection and a user - friendly design to deliver high reliability and ease of use.
Package contents When you unpack the projector, make sure you have all these components: Power COMP1 COMP2 Auto Sync HDMI Source Enter Menu 3D Exit PgUp PgDn Mouse Pattern Blank ID set 1 2 3 4 6 7 Eco Mode 5 8 Color Mode RCP01051 PJD5155L/PJD5255L/ PJD5555LW projector PJD5350LS/ PJD5550LWS projector Remote control (IR) & batteries (AAA *2 PCS) AC power cord VGA cable (D-SUB to D-SUB) ViewSonic CD wizard Optional accessories Quick start guide 1. 2. 3. 4.
Projector overview Front view 7 8 9 6 5 4 1 3 8 9 PJD5155L/PJD5255L/ PJD5555LW 6 5 4 1 1. 3. 5. 7. 9. 2 PJD5350LS/PJD5550LWS 3 Front IR remote control sensor Projection lens Ventilation holes Zoom ring Lamp cover 2. 4. 6. 8.
Rear View RS-232 MINI USB HDMI COMPUTER IN 2 1 1. Connection ports 3. AC power socket 3 2. Kensington lock Bottom View 65.89 2 1 Ceiling mount screws: M4 x 8 (Max. L = 8 mm) Unit: mm 113.54 60.01 1. Security bar 2. Ceiling mount holes Note • This projector can be used with a ceiling mount for support. The ceiling mount is not included in the package. • Contact your dealer for information to mount the projector on a ceiling.
Using the product Control panel 3 4 6 5 2 7 8 Blank Pow 1 er Menu Exit 9 Enter Color Mode Source / ? 12 1. 10 4 11 POWER Turn the projector on or off. 2. Blank/ Left key Hide the screen picture. 3. Menu/Exit Menu: Display or exit the on-screen display menus. Exit: Goes back to previous OSD menu, exits and saves menu settings. 4. Keystone/Arrow keys ( / Up, / Down) Manually correct distorted images resulting from an angled projection. 5.
Refer to “LED Indicator Messages”. 11. Color Mode Select the picture setup mode. 12. Source/ ? (Help) Source: Display the source selection bar. Help: Display the HELP menu by a long press for 3 seconds.
Connection ports 1 2 RS-232 3 4 MINI USB HDMI COMPUTER IN 1. COMPUTER IN Connect image input signal (analog RGB or component) to this jack. 2. RS-232 When operating the projector via a computer, connect this to the controlling computer's RS-232C port. 3. HDMI Connect HDMI output from video equipment to this jack. 4. MINI USB This connector is for firmware update and mouse function support.
Remote control 16 17 18 19 20 5 3 4 5 4 6 7 8 9 21 22 23 24 25 26 27 28 29 10 11 12 13 14 15 1. Power Turn the projector on or off. 2. COMP1 Display COMPUTER IN 1 signal. 3. Auto Sync Automatically determines the best picture timings for the displayed image. 4. / (Keystone) Manually correct distorted images resulting from an angled projection. 5.
Switch between the normal and mouse modes. 11. (Lock)/ID Set Lock: Activates or disables panel key lock. ID Set: Sets remote control code. 12. (Timer) Activate P-Timer OSD menu. 13. (Volume+) Increase the volume level. 14. Eco Mode Switch the lamp mode from Normal, Economic, Dynamic to Sleep. 15. (Volume-) Decrease the volume level. 16. (My Button) User definable key for customized function. 17. HDMI Display HDMI signal. 18. COMP2 Not available for PJD5 series. 19.
Using the remote mouse control The capability of operating your computer with the remote control gives you more flexibility when delivering presentations. 1. Connect the projector to your PC or notebook with a USB cable prior to using the remote control in place of your computer’s mouse. See "Connecting a computer" on page 14 for details. 2. Set the input signal to COMPUTER. 3. Press Mouse on the remote control to switch from the normal mode to the mouse mode.
Installing the batteries 1. Open the battery cover in the direction shown. 2. Install batteries as indicated by the diagram inside the compartment. 3. Close the battery cover into position. Caution • Risk of explosion if battery is replaced by an incorrect type. • Dispose of used batteries according to the instructions. • Make sure the plus and minus terminals are correctly aligned when loading a battery. Note • Keep the battery out of the reach of children.
Remote control operation Point the remote control at the infrared remote sensor and press a button. • Operating the projector from the front. 15 15 5m 8m 7m Note • The remote control may not operate when there is sunlight or other strong light such as a fluorescent lamp shining on the remote sensor. • Operate the remote control from a position where the remote sensor is visible. • Do not drop the remote control or jolt it.
Connection When connecting a signal source to the projector, be sure to: 1. Turn all equipment off before making any connections. 2. Use the correct signal cables for each source. 3. Ensure the cables are firmly inserted. 3 1 4 2 RS-232 MINI USB HDMI COMPUTER IN 1. HDMI cable 3. VGA to DVI-A cable 2. VGA (D-Sub) to HDTV (RCA) cable 4. USB cable Important • In the connections shown above, some cables may not be included with the projector (see "Package contents" on page 2).
Connecting a computer or monitor Connecting a computer The projector provides two VGA input sockets that allow you to connect them to both IBM® compatibles and Macintosh® computers. A Mac adapter is needed if you are connecting legacy version Macintosh computers. To connect the projector to a notebook or desktop computer: 1. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer. 2.
Connecting an HDMI source device Examine your Video source device to determine if it has a set of unused HDMI output jacks available: • If so, you can continue with this procedure. • If not, you will need to reassess which method you can use to connect to the device. To connect the projector to an HDMI source device: 1. Take an HDMI cable and connect one end to the HDMI output jack of the HDMI source device. 2. Connect the other end of the HDMI cable to the HDMI jack on the projector.
Operation Powering on/off the projector Powering on the projector: 1. Complete the AC power cord and peripheral signal cable(s) connections. 2. Press to turn on the projector. The projector takes a minute or so to warm up. • If the projector is still hot from previous activity, it will run the cooling fan for approximately 60 seconds before energizing the lamp. 3. Turn on your source (computer, notebook, DVD, etc.).
Adjusting the projector height Elevator foot The projector is equipped with an elevator foot to adjust the image height. To raise or lower the image, turn the elevator foot to fine-tune the height. Note • To avoid damaging the projector, make sure that the elevator foot is fully retracted before placing the projector in its carrying case. Adjusting the projector zoom and focus Zoom ring Focus ring PJD5350LS/PJD5550LWS PJD5155L/PJD5255L/PJD5555LW 1. Sharpen the image by rotating the focus ring. 2.
Adjusting projection image size Refer to the graphic and table below to determine the screen size and projection distance. Diagonal size Screen Center of lens H W Vertical offset Projection distance PJD5155L/PJD5255L 4 : 3 Screen diagonal Projection distance [inch (m)] Screen size Vertical offset [inch (cm)] Diagonal [inch (cm)] W [inch (cm)] H [inch (cm)] (min.) (max.) 30 (76) 24 (61) 18 (46) 47 (1.2) 51 (1.3) 2.7 (6.9) 40 (102) 32 (81) 24 (61) 62 (1.6) 69 (1.7) 3.6 (9.
PJD5350LS 4 : 3 Screen diagonal Screen size Projection distance [inch (m)] Vertical offset [inch (cm)] 18 (46) 15 (0.4) 2.7 (6.9) 24 (61) 20 (0.5) 3.6 (9.1) 48 (122) 36 (91) 30 (0.8) 5.4 (13.7) 64 (163) 48 (122) 40 (1.0) 7.2 (18.3) 100 (254) 80 (203) 60 (152) 50 (1.3) 9.0 (22.9) 150 (381) 120 (305) 90 (229) 75 (1.9) 13.5 (34.3) 200 (508) 160 (406) 120 (305) 100 (2.5) 18.0 (45.7) 250 (635) 200 (508) 150 (381) 125 (3.2) 22.5 (57.2) 300 (762) 240 (610) 180 (457) 150 (3.
Securing the projector Setting a password 1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Advanced > Security Settings menu. Press Enter. The Security Settings page displays. 2. Highlight Change Password and press Enter. 3. As pictured to the right, the four arrow keys ( / / / ) respectively represent 4 digits (1, 2, 3, 4). According to the password you desire to set, press the arrow keys to enter six digits for the password. 4. Confirm the new password by re-entering the new password. 5.
Disabling the password function To disable password protection, go back to SYSTEM SETTING: ADVANCED > Advanced > Security Settings > Power on Lock menu, and press Enter. You will be asked to input password. Once the password is set, the OSD menu returns to the Power On Lock. Select Off by pressing / . To leave the OSD menu, press Menu/ Exit.
Locking control keys With the control keys on the projector locked, you can prevent your projector settings from being changed accidentally (by children, for example). When the Panel Key Lock is on, no control keys on the projector will operate except Power. 1. Press Lock on the remote control or keypad on the projector for 3 seconds.Press Lock on the remote control, a confirmation message “Are you sure to lock panel keys?” is displayed. Select Yes to confirm.
Setting the presentation timer The presentation timer can indicate the presentation time on the screen to help you achieve better time management when giving presentations. Follow these steps to utilize this function: 1. Press Timer on the remote control to access the Presentation Timer menu or go to the SYSTEM SETTING: BASIC > Advanced > Presentation Timer menu and press Enter to display the Presentation Timer page. 2. Highlight Timer Period and decide the timer period by pressing / . 3.
Menu operation The projector has multilingual on-screen display menus that allow you to make image adjustments and change a variety of settings. How to operate 1. Press Menu to open the OSD menu. 2. When OSD is displayed, use / to select any feature in the main menu. 3. After selecting the desired main menu item, press to enter sub-menu for feature setting. 4. Use / to select the desired item and adjust the settings with / . 5.
Menu tree Main Menu Sub Menu Screen Color Aspect Ratio Keystone DISPLAY Position Phase H. Size Zoom Color Mode Brightness Contrast Color Temp. OverScan HDMI Settings PICTURE Advanced Reset Color Settings Settings Off / Blackboard / Greenboard / Whiteboard Auto / 4:3 / 16:9 (PJD5155L/PJD5255L/ PJD5350LS) / 16:10 (PJD5555LW/ PJD5550LWS) / Wide / Anamorphic/ -40 - 40 X: -5 - 5 Y: - 5 - 5 0 - 31 -15 - 15 PC:1.0X - 2.0X Video:1.0X - 1.
Quick Auto Search 3D Settings SOURCE Off / On 3D Sync 3D Sync Invert Computer CEC Auto Power On Direct Power On Power Saving Auto Power Off Sleep Timer Smart Restart Quick Power Off Disable / Enable Disable / Enable 26 Auto Off Frame Sequential Frame Packing Top-Bottom Side-by-Side Disable /Invert Disable/ Enable Disable/ Enable Off / On Disable/ 10/ 20/ 30 min Disable / 30 min/ 1 hr / 2 hr / 3 hr / 4 hr / 8 hr / 12 hr
Language Projector Posi- Front Table / Rear Table / Rear Ceiling / Front tion Ceiling Menu Display 5 sec / 10 sec / 15 sec / 20 sec / Time 25 sec / 30 sec Menu Settings Center / Top-Left / Top-Right / Menu Position Bottom-Left / Bottom-Right Disable / 5 min / 10 min / 15 min / 20 min / 25 min Blank Timer / 30 min Splash Screen Black / Blue / ViewSonic/ Off Auto Sync / Projector Position / Menu Position / Color Temp.
High Altitude Mode DCR Audio Settings Off / On Off / On Mute Audio Volume Power On/Off Ring Tone Lamp Mode SYSTEM SETTING: ADVANCED Lamp Settings Filter Settings Remote Control Code INFORMATION Reset Lamp Hours Lamp hours Filter Mode Reset Filter Hours Filter Hours Off / On 0 - 20 On/ Off Normal / Economic / Dynamic / Sleep Mode Reset / Cancel Off / On Reset / Cancel 1/2/3/4/5/6/7/8 Change password Security Settings Advanced Power on Lock Off / On Panel Key Lock Off / On Reset Settings Reset / Canc
DISPLAY Screen Color The Screen Color feature can help correct the projected picture’s colors to prevent possible color difference between the source and projected pictures. There are several precalibrated colors to choose from: Whiteboard, Greenboard, and Blackboard. Aspect Ratio Select how the picture fits on the screen: • Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal or vertical width.
Zoom Using the remote control 1. Press on the remote control to display the Zoom bar. 2. Press 3. Press / to magnify the picture to a desired size. repeatedly to magnify the picture to a desired size. 4. To navigate the picture, press Enter to switch to the paning mode and press the directional arrows ( , , , ) to navigate the picture. 5. To reduce size of the picture, press Enter to switch back to the zoom in/out functionality, and press Auto Sync to restore the picture to its original size.
PICTURE Color Mode There are many factory presets optimized for various types of images. • Brightest: Maximizes the brightness of the projected image. This mode is suitable for environments where extra-high brightness is required. • Dynamic: Is designed for presentations under daylight environment to match PC and notebook coloring. In addition, the projector will optimize the image quality using the dynamic PC function in accordance with the projected contents.
• Enhanced: The range for HDMI output signal is from 0 - 255. • Normal: The range for HDMI output signal is from 16 - 235. Advanced Color The higher the value, the more reddish the picture becomes. The lower the value, the more greenish the picture becomes. Tint Adjusts the red and green color tones of the image. Sharpness Adjusts the image to make it look sharper or softer. Gamma Effect the represent of dark scenery. With greater gamma value, dark scenery will look brighter.
SOURCE Quick Auto Search Automatically scan through all the input source if the function in the OSD menu is On. The function will stop the signal auto scan process and fix the signal source you preferred if you turn Off the Quick Auto Search. 3D Settings This projector features a 3D function which enables you to enjoy the 3D movies, videos, and sporting events in a more realistic way by presenting the depth of the images. You need to wear a pair of 3D glasses to view the 3D images.
The projector lowers the projector power if no input source is detected after 5 minutes to prevent unnecessary waste of lamp life. You can further decide if you would like the projector to turn off automatically after a set period of time. When Disable is selected, the projector power will be reduced to 30% after no signal is detected for 5 minutes. If you select 10 min, 20 min or 30 min, the projecter power will be reduced to 30% after no signal is detected for 5 minutes.
SYSTEM SETTING: BASIC Language Select the language used by the on-screen menu. Projector Position Adjust the picture to match the orientation of the projector: upright or upside-down, in front of or behind the screen. Invert or reverse the image accordingly. Menu Settings Menu Display Time Duration of OSD menu display countly starts (at idle state by second). Menu Position Choose the menu location on the display screen.
SYSTEM SETTING: ADVANCED High Altitude Mode Use this function to allow the fans operates at full speed continuously to achieve proper high altitude cooling of the projector. DCR DCR (Dynamic Contrast Ratio): Enable DCR will further enhance contrast ratio by darkening the black scenes. Disable DCR will resume to normal contrast performance. DCR will impact lamp life and system noise performance. Audio Settings Mute Cuts off the sound temporarily. Audio Volume Adjusts the projector’s volume level.
Remote Control Code See "Remote control code" on page 10 for details. Advanced Security Settings • Change Password: Allows you to set or change the password. • Power on Lock: If you enable this function, you will have to enter the password next time you turn on the projector. See "Securing the projector" on page 20 for details. Panel Key Lock Disables or enables all panel key functions except Power on the projector and keys on the remote control. See "Locking control keys" on page 22 for details.
INFORMATION Current System Status Shows the currect system status. Source Shows the current signal source. Color Mode Shows the selected mode in the Color Mode menu. Resolution Shows the native resolution of the input signal. Color System Shows input system format, NTSC, PAL, SECAM, or RGB. Lamp Hours Displays the number of hours the lamp has been used. Filter Hours Displays the number of hours the filter has been used. Firmware Version Shows firmware version.
Maintenance The projector needs proper maintenance. You should keep the lens clean as dust, dirt or spots will project on the screen and diminish image quality. If any other parts need replacing, contact your dealer or qualified service personnel. When cleaning any part of the projector, always switch off and unplug the projector first. Warning • Never open any of the covers on the projector. Dangerous electrical voltages inside the projector can cause severe injury.
Installing the dust filter (optional accessory) Caution • It is important to clean the dust filter every 100 hours after the dust filter is installed. • Be sure to turn off the projector and unplug it from power source before installing or detaching the filter. • If your projector is ceiling-mounted or is not easily accessible, pay special attention to your personal safety when replacing the dust filter. Installing the dust filter 1. Be sure to turn off the projector and unplug it from power source. 2.
Resetting the filter timer 5. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Filter Settings menu. 6. Press Enter and the Filter Settings page is displayed. 7. Highlight Reset Filter Hours and press Enter. A warning message is displayed asking if you want to reset the filter timer. 8. Highlight Reset and press Enter. The lamp timer will be reset to '0'.
Replacing the lamp As the projector operates over time, the brightness of the projector lamp gradually decreases and the lamp becomes more susceptible to breakage. We recommend replacing the lamp if a warning message is displayed. Do not attempt to replace the lamp yourself. Contact the qualified service personnel for replacement. Note • The lamp is extremely hot right after turning off the projector. If you touch the lamp, you may scald your finger.
1. Turn off the projector. 2. If the projector is installed in a ceiling mount, remove it. 3. Unplug the power cord. 4. Loosen the screw in the side of the lamp cover.1 5. Remove the cover.2 6. Loosen the screws from the lamp module.3 7. Raise the handle and pull out the lamp module slowly and carefully.4 8. Insert the new lamp module into the projector and tighten the screws. 9. Replace the lamp cover and tighten the screw. 10. Turn on the projector.
Specifications Model name Dislay system Resolution Zoom F/No. Focal length Screen size Lamp Input terminal Output terminal Control terminal Speaker Video compatibility Scanning frequency Horizontal frequency Vertical frequency Environment PJD5155L PJD5255L PJD5555LW Single 0.55" DLP panel Single 0.65" DLP panel SVGA (800 x 600 XGA (1024 x WXGA (1280 x 800 pixels) 768 pixels) pixels) 1.1x 1.2x 2.5 - 2.7 2.56 22.08 - 24.28mm 20.99 - 25.
Model name Display system Resolution Zoom F/No. Focal length Screen size Lamp Input terminal Output terminal Control terminal Speaker Video compatibility PJD5350LS PJD5550LWS Single 0.55" DLP panel Single 0.65" DLP panel XGA (1024 x 768 pixels) WXGA (1280 x 800 pixels) Fix 2.8 7.26mm 7.51mm 30” - 300” 210W D-Sub 15-pin x 1, HDMI x 1 D-Sub 15 pin x 1 RS-232 x 1, Mini-B USB x1 (supports firmware upgrade and remote mouse control) 2 watt x 1 NTSC, NTSC 4.
Dimensions PJD5155L/PJD5255L/PJD5555LW 362 mm (W) x 231 mm (D) x 109 mm (H) 362 231 109 PJD5350LS/PJD5550LWS 362 mm (W) x 248 mm (D) x 116 mm (H) 362 248 116 Ceiling mount installation Ceiling mount screws: M4 x 8 (Max.
Appendix LED indicator messages LED Type Power LED Temp LED Lamp LED Power LED Temp LED Lamp LED Power LED Temp LED Lamp LED Power LED Temp LED Lamp LED Power LED Temp LED Lamp LED Power LED Temp LED Lamp LED Power LED Temp LED Lamp LED Color Blue Red Red Blue Red Red Blue Red Red Blue Red Red Blue Red Red Blue Red Red Blue Red Red Status Solid Off Off Flash Off Off Flash Off Off Solid Off Off Solid Off Off Solid Flash Flash Solid Off Flash Power LED Temp LED Lamp LED Blue Red Red Flash Flash Off Powe
Compatibility modes Supported 3D signal for PC input Resolution 640 x 480 720 x 400 800 x 600 1024 x 768 1152 x 864 1280 x 720 1280 x 768 1280 x 800 1280 x 1024 1280 x 960 1360 x 768 1440 x 900 1400 x 1050 1600 x 1200 1680 x 1050 1920 x 1200 640 x 480 @67Hz 832 x 624 @75Hz 1024 x 768 @75Hz 1152 x 870 @75Hz Horizontal frequency (KHz) 59.94 72.809 75 85.008 70.087 60.317 72.188 75 85.061 119.854 60.004 70.069 75.029 84.997 119.989 75 60 120 59.87 59.81 74.934 84.88 119.909 60.02 75.025 85.024 60 85.
Supported timing for Component-YPbPr input Timing Resolution Vertical Frequency (Hz) 480i* 480p* 576i 576p 720/50p 720/60p* 1080/50i 1080/60i 1080/24P 1080/25P 1080/30P 1080/50P 1080/60P 720 x 480 720 x 480 720 x 576 720 x 576 1280 x 720 1280 x 720 1920 x 1080 1920 x 1080 1920 x 1080 1920 x 1080 1920 x 1080 1920 x 1080 1920 x 1080 59.94 59.94 50 50 50 60 50 60 24 25 30 50 60 Horizontal Frequency (kHz) 15.73 31.47 15.63 31.25 37.5 45.00 28.13 33.75 27 28.13 33.75 56.25 67.5 Pixel Frequency (MHz) 13.
Troubleshooting Refer to the symptoms and measures listed below before sending the projector for repairs. If the problem persists, contact your local reseller or service center. Please refer to "LED Indicator Messages" as well. Start-up problems If no lights turn on: • Be sure that the power cord is securely connected to the projector and the other end is plugged into an outlet with power. • Press the power button again.
RS-232 command and configuration D-Sub 9 pin 1 2 3 4 5 6 7 8 9 Wire List 1 CD RXD TXD DTR GND DSR RTS CTS RI C1 1 2 3 4 5 6 7 8 9 SHELL Baud Rate Data Length Parity Check Stop Bit Flow Control COLOR Black Brown Red Orange Yellow Green Blue Purple White DW 115200 bps 8 bit None 1 bit None 51 C2 1 3 2 6 5 4 8 7 9 SHELL
Function Status Write Power Read Reset all settings Reset Color Settings Write Splash Screen Read Write Quick Power Off Read Write High Altitude Mode Read Write Lamp Mode Read Write Message Read Write Projector Position Read Write 3D Sync Read Write 3D Sync Invert Read Action cmd Power on Power off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 Power status (on/off) 0x5E Execute 0x06 0x14 0x00
Write Contrast Read Write Brightness Read Write Aspect ratio Read Auto Adjust Write Horizontal position Read Write Vertical position Read Write Color temperature Read Write Blank Read KeystoneVertical KeystoneHorizontal Write Read Write Read Write Color mode Read Contrast decrease Contrast increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x00 0x60 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x02 0x01 0x61 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x02 Contrast ratio 0x61 Brightness decrease 0x06 0x14 0x
Write Primary color R Primary color G Primary color B Primary color C Primary color M Primary color Y Read Primary color status Write Hue decrease Hue increase Read Hue Write Saturation decrease Saturation increase Read Saturation Write Gain decrease Gain increase Read Gain Write Freeze On Freeze Off Read Freeze status Primary Color Hue Saturation Gain Freeze Write Source input Read Write Quick Auto Search Read Write Mute Read Write Volume Read 0x06 0x14 0x00 0x04 0x00 0x34 0x12
English Deutsch Italiano Write Language Svenska Nederlands Polski Suomi Indonesia Read Language Write Reset Lamp usuage hour Read Lamp usuage hour Write RGB YUV Auto Read HDMI Format status Write Enhanced Normal Auto Read HDMI Range status Write Off On Read CEC status Read Read error status Write Brilliant Color 0 Brilliant Color 1 Brilliant Color 2 Brilliant Color 3 Brilliant Color 4 Brilliant Color 5 Brilliant Color 6 Brilliant Color 7 Brilliant Color 8 Brilliant Color 9 Brilliant
Remote Control code Write Read Write Screen Color Read Screen Color status Write Overscan Off Overscan 1 Overscan 2 Overscan 3 Overscan 4 Overscan 5 Read Overscan status Write Menu Exit Top Bottom Left Right Source Enter Auto My Button Over Scan Remote Key code 1 code 2 code 3 code 4 code 5 code 6 code 7 code 8 Remote Control code status Screen color Off Blackboard Greenboard Whiteboard 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x00 0xA0 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x01 0xA1 0x06 0x1
IR control table System Code: 83F4 Format : NEC Power COMP1 COMP2 Auto Sync HDMI Source Enter Menu 3D Exit PgUp PgDn Mouse Pattern Blank ID set 1 2 3 4 5 6 7 Eco Mode 8 Color Mode RCP01051 57
Key Freeze PgDn PgUp Blank Auto sync Up Down Left Right Color Mode Aspect Mute Enter Power ON Magnify Presentation Timer Exit D.
Customer Support For technical support or product service, see the table below or contact your reseller. NOTE: You will need the product serial number. Country/Region Website T= Telephone C = CHAT ONLINE Email Australia New Zealand www.viewsonic.com.au AUS= 1800 880 818 NZ= 0800 008 822 service@au.viewsonic.com Canada www.viewsonic.com T (Toll-Free)= 1-866-463-4775 T (Toll)= 1-424-233-2533 service.ca@viewsonic.com Europe www.viewsoniceurope.com www.viewsoniceurope.
Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
How to get service: 1. For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to Customer Support page). You will need to provide your product's serial number. 2. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product. 3.
Mexico Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components & accessories.
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico: Name, address, of manufacturer and importers: México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004 Hermosillo: Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col. Bugambilias C.