PJD6350/PJD6351LS/PJD6352/ PJD6352LS/PJD6550LW/ PJD6551LWS/PJD6552LW/ PJD6552LWS DLP Projector User Guide IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic Corporation, which is also found on our web site at http:// www.viewsonic.
Thank you for choosing ViewSonic As a world leading provider of visual solutions, ViewSonic is dedicated to exceeding the world’s expectations for technological evolution, innovation, and simplicity. At ViewSonic, we believe that our products have the potential to make a positive impact in the world, and we are confident that the ViewSonic product you have chosen will serve you well.
Compliance Information FCC Compliance Statement This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Substance Proposed Maximum Concentration Actual Concentration Lead (Pb) 0.1% < 0.
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this unit near water. 6. Clean with a soft, dry cloth. 7. Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other devices (including amplifiers) that produce heat. 9.
Copyright Information Copyright © ViewSonic Corporation, 2017. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic and the three birds logo are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association. DPMS and DDC are trademarks of VESA.
Product Registration To fulfill possible future product needs, and to receive additional product information as it becomes available, please visit your region section on ViewSonic’s website to register your product online. The ViewSonic CD also provides an opportunity for you to print the product registration form. Upon completion, please mail or fax to a respective ViewSonic office. To find your registration form, use the directory “:\CD\Registration”.
Table of contents Important safety instructions .......................2 Using the CEC function..................... 38 Using the 3D functions ...................... 38 Controlling the projector through a LAN environment ........................... 39 Using the projector in standby mode. 44 Adjusting the sound ........................... 45 Shutting down the projector .............. 47 Menu operation.................................. 48 Introduction......................4 Projector features ..............
Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product. Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Please read this manual before you operate your projector. Save it for future reference. Do not look straight at the projector lens during operation.
13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire. - Do not place this projector on a blanket, bedding or any other soft surface. - Do not cover this projector with a cloth or any other item. - Do not place inflammables near the projector. 14. Always place the projector on a level, horizontal surface during operation.
Introduction Projector features The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use. The projector offers the following features. • • • • • • • • • • • • • • • • • • • Dynamic mode adjusting the power consumption of the lamp according to the brightness of the image being projected Power saving function decreasing the power consumption of the lamp by up to 70% when no input signal can be detected for a set period of time.
Shipping contents Carefully unpack and verify that you have all of the items shown below. If any of these items are missing, please contact your place of purchase. Standard accessories The supplied accessories will be suitable for your region, and may differ from those illustrated.
Projector exterior view 1. Front/upper side PJD6350/PJD6352 PJD6550Lw/PJD6552Lw 1 2. 3. 4. 5. 6. 6 2 3 7 4 5 8 7. 8. 9. 10. 11. PJD6351Ls/PJD6352Ls PJD6551Lws/PJD6552Lws 1 6 2 3 12. 13. 14. 15. 16. 17. 7 4 5 8 9 Rear/lower side 10 11 12 13 14 15 18. 16 17 18 19 20 21 19. 20. 21. 22. 23. 22 External control panel (See "Projector" on page 7 for details.
Controls and functions Projector PJD6350/PJD6352 PJD6550Lw/PJD6552Lw PJD6351Ls/PJD6352Ls PJD6551Lws/PJD6552Lws 1 2 1 4 3 7 1. 2. 3. 4. 6 4 7 4 Focus ring Adjusts the focus of the projected image. Zoom ring Adjusts the size of the projected image. Menu Turns on the On-Screen Display (OSD) menu. Exit Goes back to previous OSD menu, exits and saves menu settings. / / / (Keystone keys) Manually corrects distorted images resulting from an angled projection. 6.
Remote control 14 15 1 2 3 4 COMP1 COMP2 Auto Sync 4 5 4 6 7 8 9 10 11 12 HDMI Source 4 Enter Menu Exit PgUp PgDn Mouse Pattern Blank Eco Mode Audio Mode Color Mode 13 To use the remote mouse control keys (Page Up, Page Down, , and ), see "Using the remote mouse control" on page 10 for details. 1. 2. Power Toggles the projector between standby mode and Power ON. Source selection keys • COMP1/COMP2 5. 6. 7. Selects D-Sub / Comp. 1 or D-Sub / Comp. 2 source for display. • 3. 4.
9. 18. Mouse Switches between the normal and mouse modes. PgUp, PgDn, , : active after pressing 19. Mouse. An icon appears on the screen to indicate the activation of the mouse mode. Only available when a PC input signal is selected. 10. (Panel Key Lock) Activates panel key lock. 11. (Presentation Timer) Displays the presentation timer settings menu. 12. (Volume) Displays the volume adjustment bar. Eco Mode Selects a lamp mode. LED indicator 13. 14. 15. 16. 17.
To switch the code for the remote control, press ID set and the number button corresponding to the remote control code set in the projector OSD together for 5 seconds or more. The initial code is set to 1. When the code is switched to 8, the remote control can control every projector. COMP1 COMP2 Auto Sync HDMI Source Enter Menu Exit PgUp If different codes are set on the projector and remote control, there will be no response from the remote control.
Replacing the remote control batteries 1. 2. 3. To open the battery cover, turn the remote control over to view its back, press on the finger grip on the cover and pull it up in the direction of the arrow as illustrated. Remove any existing batteries (if necessary) and install two AAA batteries observing the battery polarities as indicated in the base of the battery compartment. Positive (+) goes to positive and negative (-) goes to negative.
Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment. Your projector is designed to be installed in one of the following 4 possible installation locations: 1.
Projection dimensions The "screen" mentioned below refers to the projection screen usually consisting of a screen surface and a support structure. PJD6350/PJD6352/PJD6351Ls/PJD6352Ls • 4:3 image on a 4:3 screen (a) (b) (e) (a) (f) (d) (c) (c) (d) (f) (e) • (b) 16:9 image on a 4:3 screen (a) (b) (a) (e) (f) (d) (c) (c) (d) (f) (b) (e) (e): Screen (f): Center of lens PJD6350/PJD6352 (a) Screen Size [inch (m)] 4:3 image on a 4:3 Screen (b) Projection distance [m (inch)] min. max.
PJD6351Ls/PJD6352Ls 4:3 image on a 4:3 Screen 16:9 image on a 4:3 Screen (a) Screen Size [inch (m)] (b) Projection distance [m (inch)] (c) Image height [cm (inch)] 30 (0.8) 0.4 (15) 40 40 (1.0) 0.5 (19) 54 50 (1.3) 0.6 (24) 67 (26) 10.1 60 (1.5) 0.74 (29) 81 (32) 12.1 70 (1.8) 0.86 (34) 94 (37) 14.1 (5.6) 0.86 (34) 89 (35) 22.2 (8.8) 80 (2.0) 0.99 (39) 108 (42) 16.2 (6.4) 0.99 (39) 102 (40) 25.4 (10.
PJD6550Lw/PJD6552Lw/PJD6551Lws/PJD6552Lws • 16:10 image on a 16:10 screen (a) (b) (e) (a) (f) (d) (c) (c) (d) (f) (b) (e) • 16:10 image on a 4:3 screen (a) (b) (a) (e) (f) (d) (c) (c) (d) (f) (b) (e) (e): Screen (f): Center of lens PJD6550Lw/PJD6552Lw (a) Screen Size [inch (m)] 16:10 image on a 16:10 Screen (b) Projection distance [m (inch)] min. max. (c) Image (d) Vertical height offset [cm (inch)] [cm (inch)] 16:10 image on a 4:3 Screen (b) Projection distance [m (inch)] min.
PJD6551Lws/PJD6552Lws 16:10 image on a 16:10 Screen (a) Screen Size [inch (m)] (b) Projection distance [m (inch)] (c) Image height [cm (inch)] (d) Vertical offset [cm (inch)] 16:10 image on a 4:3 Screen (b) Projection distance [m (inch)] (c) Image height [cm (inch)] (d) Vertical offset [cm (inch)] 30 (0.8) 0.32 (12) 40 (16) 2.0 (0.8) 0.30 (12) 38 (15) 1.9 (0.8) 40 (1.0) 0.42 (17) 54 (21) 2.7 (1.1) 0.40 (16) 51 (20) 2.5 (1.0) 50 (1.3) 0.53 (21) 67 (26) 3.4 (1.3) 0.
Connection When connecting a signal source to the projector, be sure to: 1. 2. 3. Turn all equipment off before making any connections. Use the correct signal cables for each source. Ensure the cables are firmly inserted. In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 5). They are commercially available from electronics stores. The connection illustrations below are for reference only.
Connecting a computer or monitor Connecting a computer 1. 2. 3. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer. Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER IN 2 signal input socket on the projector. If you wish to use the remote mouse control function, take a USB cable and connect the larger end to the USB port of the computer, and smaller end to the MINI USB socket on the projector.
Connecting Video source devices You can connect your projector to various Video source devices that provide any one of the following output sockets: • HDMI • Component Video • S-Video • Video (composite) You need only connect the projector to a Video source device using just one of the above connecting methods, however each provides a different level of video quality.
If you have a separate sound system, you will most likely want to connect the audio output of your Video source device to that sound system, instead of to the mono audio projector. Connecting an HDMI device You should use an HDMI cable when making connection between the projector and HDMI devices. 1. 2. Take an HDMI cable and connect one end to the HDMI output port of the video device. Connect the other end of the cable to the HDMI input port on the projector.
Connecting an S-Video source device Examine your Video source device to determine if it has an unused S-Video output socket available: • • 1. 2. If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. Take an S-Video cable and connect one end to the S-Video output socket of the Video source device. Connect the other end of the S-Video cable to the S-VIDEO socket on the projector.
About the microphone input • • If you wish to use a microphone, connect a 3.5 mini jack cable microphone to the projector. You can use a wireless microphone as long as a wireless module is attached to the projector’s microphone input jack and it works well with the associated devices. To ensure a quality use of the wireless microphone, it is recommended that your microphone conforms to the specifications listed in the table below.
Operation Starting up the projector 1. 2. 3. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). (If available) Remove the lens cap. Press Power to start the projector. As soon as the lamp lights up, a "Power On Ring Tone" will be heard. The Power indicator light stays blue when the projector is on. (If necessary) Rotate the focus ring to adjust the image clearness.
Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. The OSD screenshots below are for reference only, and may differ from the actual design. Below is the overview of the OSD menu. Main menu icon Screen Color Aspect Ratio Keystone Corner Adj. Position Phase H. Size Zoom Highlight Sub-menu Current input signal Off Auto ENTER 16 0 Analog RGB MENU Exit Status Go to the previous page or to exit.
Utilizing the password function For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on page 24. You will be inconvenienced if you enable the password function yet forget the password somehow. Do make a note of your password, and keep the note in a safe place for later recall.
Entering the password recall procedure 1. 2. 3. Press and hold Auto Sync on the remote control for 3 seconds. The projector will display a coded number on the screen. Write down the number and turn off your projector. Seek help from the local service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector. RECALL PASSWORD Please write down the recall code, and contact ViewSonic Customer Center.
Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. Be sure the Quick Auto Search function in the SOURCE menu is On if you want the projector to automatically search for the signals. You can also manually select the desired signal by pressing one of the source selection keys on the remote control, or cycle through the available input signals. 1. 2. Press Source. A source selection bar is displayed.
• 4. Auto: Sets the projector to detect the color space setting of the input signal automatically. Highlight HDMI Range and press / to select a suitable HDMI color range according to the color range setting of the output device connected. • Enhanced: Sets the HDMI color range as 0 - 255. • Normal: Sets the HDMI color range as 15 - 235. • Auto: Sets the projector to detect the HDMI range of the input signal automatically. This function is only available when the HDMI input port is in use.
Fine-tuning the image clarity 1. Adjust the projected image to the size 2. that you need using the zoom ring. If necessary, sharpen the image by rotating the focus ring. PJD6350/PJD6352 PJD6550Lw/PJD6552Lw PJD6351Ls/PJD6352Ls PJD6551Lws/PJD6552Lws PJD6350/PJD6352 PJD6550Lw/PJD6552Lw Correcting keystone Keystoning refers to the situation where the projected image is noticeably wider at either the top or bottom. It occurs when the projector is not perpendicular to the screen.
3. Press the button that represents the corner you wish to adjust and press Enter. 4. Press / to select an adjustment method that suits your need and press Enter. 5. Press / / / to adjust its shape and size. During this process, you can press Menu or Exit to go back to a previous step. A long press for 2 seconds on Enter will reset the settings. Adjusting keystone or aspect ratio will reset the Corner Adj. settings.
1. Auto: Scales an image proportionally to fit the projector's native resolution in its horizontal width. This is suitable for the incoming image which is neither in 4:3 nor 16:9 and you want to make most use of the screen without altering the image's aspect ratio. 16:10 picture 15:9 picture 2. 3. 4. 5. 6. 7. 4:3: Scales an image so that it is displayed in the center of the screen with a 4:3 aspect ratio.
8. Anamorphic: Scales a 2.35:1 aspect image so that it fills the screen. 2.35:1 picture Optimizing the image Selecting a picture mode The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type. To select an operation mode that suits your need, you can follow one of the following steps. • • Press Color Mode repeatedly until your desired mode is selected.
Adjusting Brightness Go to the PICTURE > Brightness menu and press / . The higher the value, the brighter the image. And the lower the setting, the darker the image. Adjust this control so the black areas of the image appear just as black and that detail in the dark areas is visible. -30 50 +80 0 +40 Adjusting Contrast Go to the PICTURE > Contrast menu and press / . The higher the value, the greater the contrast.
Go to the PICTURE > Color Temp. menu and press / . The options available for color temperature* settings vary according to the signal type selected. 1. Cool: With the highest color temperature, Cool makes the image appear the most bluish white than other settings. 2. Neutral: Makes images appear bluish white. 3. Normal: Maintains normal colorings for white. 4. Warm: Makes images appear reddish white.
5. Please refer to the illustration to the right for how the colors relate to each other. For example, if you select Red and set its range at 0, only pure red in the projected picture will be selected. Increasing its range will include red close to yellow and red close to magenta. Press to highlight Saturation and adjust its values to your preference by pressing / . Every adjustment made will reflect to the image immediately.
6. Press to highlight Timer Counting Direction and select your desired counting direction by pressing / . Selection Count Up Count Down 7. 8. 9. Description Increases from 0 to the preset time. Decreases from the preset time to 0. Press to highlight Sound Reminder and decide if you want to activate sound reminder by pressing / . If you select On, a double beep sound will be heard at the last 30 seconds of counting down/up, and a triple beep sound will be produced when the timer is up.
Keys on the remote control are still functional when panel key lock is enabled. If you press Power to turn off the projector without disabling panel key lock, the projector will still be in locked status the next time it is turned on. Creating your own startup screen In addition to selecting the projector preset startup screen from among Black, Blue, or ViewSonic screen, you can make your own startup screen that is a picture projected from your computer or video source.
Using the CEC function This projector supports CEC (Consumer Electronics Control) function for synchronized power on/off operation via HDMI connection. That is, if a device that also supports CEC function is connected to the HDMI input of the projector, when the projector’s power is turned off, the power of the connected device will also be turned off automatically. When the power of the connected device is turned on, the projector’s power will be turned on automatically. To turn on the CEC function: 1. 2.
Controlling the projector through a LAN environment The projector supports Crestron® software. With correct settings for the LAN Control Settings menu, you can manage the projector from a computer using a web browser when the computer and the projector are properly connected to the same local area network. (An example of connection) Configuring the LAN Control Settings If you are in a DHCP environment: 1. 2. 3. 4. 5. 6.
If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server settings will display 0.0.0.0. Make sure the cables are properly connected and perform the procedures above again. If you wish to connect to the projector in its standby mode, be sure you have selected Static IP and obtained the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server information when the projector is on.
4. If your projector is connected to a network which supports Simple Mail Transfer Protocol (SMTP), you can configure it to alert you via email on significant events. 5. The Crestron (e-Control) page displays the Crestron e-Control user interface. See "About Crestron e-Control®" on page 42 for details.
/ > < $ % + \ ' " are prohibited. About Crestron e-Control® 1. The Crestron e-Control® page provides a variety of virtual keys to control the projector or adjust the projected pictures. i ii i You can press / to reveal more buttons. i i. These buttons function the same as the ones on the OSD menus or remote control. See "2. PICTURE menu" on page 52 and "Projector" on page 7 for details. ii. To switch between input signals, click on your desired signal.
ii. You can name the projector, keep track of its location and the person in charge of it. iii. You can adjust the LAN Control Settings. iv. Once set, access to the remote network operation on this projector has been password-protected. v. Once set, access to the tools page has been password-protected. To prevent errors, only input the English alphabet and digits on the tools page. After making the adjustments, press the Send button and the data will be saved for the projector. vi.
3. The info page displays the information and status of this projector. Press Exit to go back to the remote network operation page. 4. After pressing the button “Contact IT Help”, the HELP DESK window will appear in the upper right corner of the screen. You will be able to deliver messages to RoomView™ software administrators/users who connect to the same local area network. For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
Active VGA Out Selecting On outputs a VGA signal when the COMPUTER IN 1 and COMPUTER OUT sockets are correctly connected to devices. The projector outputs the signal received only from COMPUTER IN 1. Active Audio Out Selecting On outputs an audio signal when the AUDIO IN 1 socket is correctly connected to a proper device. LAN Control Selecting On allows the projector to provide the network function when it is in standby mode. See "Controlling the projector through a LAN environment" on page 39 for details.
Adjusting the Audio In 2 setting 1. 2. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Audio Settings > Audio In 2 menu. Press / to decide the audio input source for the AUDIO IN 2/MIC port. This will affect the connection method for different devices, and where the sound is from. • When Audio is selected: Device COMPUTER IN 1 COMPUTER IN 2 Video/S-Video AUDIO IN 1 AUDIO IN 2 AUDIO IN 2 The projector can play AUDIO IN 1 the sound from...
Shutting down the projector 1. Press Power and a confirmation message is displayed prompting you. If you don't respond in a few seconds, the message will disappear. 2. 3. Press Power a second time. Once the cooling process finishes, a "Power Off Ring Tone" will be heard. Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time. To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 46 for details.
Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible.
Main menu Sub-menu Quick Auto Search 3D Settings 3. SOURCE 3D Sync 3D Sync Invert Active VGA Out Standby Active Audio Out Settings LAN Control Computer Auto Power On CEC Direct Power On Power Saving Auto Power Off Sleep Timer Smart Restart Quick Power Off 4.
Main menu Sub-menu Pattern Message Options Off/1/2/3 On/Off Timer Period 4. Timer Display SYSTEM Advanced Timer Position SETTING: Presentation Timer Timer Counting BASIC Direction Sound Reminder Start Counting/Off High Altitude Mode On/Off DCR On/Off Standard/Speech/ Audio Mode Entertainment Mute On/Off Audio Volume Audio Settings Audio In 2 Audio/Microphone Microphone Volume Power On/Off Ring On/Off Tone 5.
Description of each menu Function Description See "Using Screen Color" on page 32 for details. Screen Color This function is only available when a PC input signal is selected. Aspect Ratio See "Selecting the aspect ratio" on page 30 for details. Keystone See "Correcting keystone" on page 29 for details. Corner Adj. See "Adjusting 4 corners" on page 29 for details. 1. DISPLAY menu Position Displays the position adjustment page. To move the projected image, use the directional arrow keys.
Function Description Color See "Adjusting Color" on page 33 for details. Tint See "Adjusting Tint" on page 33 for details. 2. PICTURE menu The function is only available when Video or S-Video input with NTSC system is selected. Advanced Sharpness See "Adjusting Sharpness" on page 33 for details. Gamma See "Selecting a gamma setting" on page 33 for details. Brilliant Color See "Adjusting Brilliant Color" on page 33 for details. Noise Reduction See "Reducing image noise" on page 33 for details.
Function Auto Power Off 3. SOURCE menu Smart Restart Description Power Saving See "Setting Power Saving" on page 59 for details. Sleep Timer See "Setting Sleep Timer" on page 59 for details. Selecting Enable enables you to restart the projector immediately within 120 seconds after turning it off. After 120 seconds, if the projector is not turned on again, it will directly enter the standby mode. It takes some time to initiate this function.
Function 4. SYSTEM SETTING: BASIC menu Splash Screen Screen Capture My Button Description Allows you to select which logo screen will be displayed during projector start-up. See "Creating your own startup screen" on page 37 for details. Sets a hotkey on remote control. Pattern The projector can display several test patterns. It helps you adjust the image size and focus and check that the projected image is free from distortion.
Function Description Selects a preferred closed captioning mode when the selected input signal carries closed captions. • 5. SYSTEM SETTING: ADVANCED menu Closed Caption Captions: An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked as "CC" in TV listings). This function is only available when a Composite video or S-Video input signal is selected and its system format is NTSC.
Function Description Source Shows the current signal source. Color Mode Shows the selected mode in the PICTURE menu. Resolution Shows the native resolution of the input signal. 6. INFORMATION menu Color System Shows input system format. Lamp Hours Current System Displays the number of hours the lamp has been used. Status Filter Hours Displays the number of hours the filter has been used. IP Address Shows the IP address of your projector. MAC Address Shows the MAC Address of your projector.
Maintenance Care of the projector You need to keep the lens and/or filter (optional accessory) clean on a regular basis. Never remove any parts of the projector. Contact your dealer when any part of the projector needs replacing. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface. • • Use a canister of compressed air to remove dust. If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface.
• If your projector is ceiling-mounted or is not easily accessible, pay special attention to your personal safety when replacing the dust filter. Installing the dust filter 1. 2. Be sure to turn off the projector and unplug it from power source. As the arrows shown to the right, fit the filter by aligning and inserting it into the projector slots. Make sure it clicks into place. For first time installation: 3. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Filter Settings menu. 4.
Lamp information Getting to know the lamp hour When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. To obtain the lamp hour information: 1. Open the OSD menu and go to the SYSTEM SETTING: ADVANCED > Lamp Settings menu. 2. Press Enter and the Lamp Settings page is displayed. 3. You will see the Lamp Hours information on the menu. 4. To leave the menu, press Exit. You can also get the lamp hour information on the INFORMATION menu.
Timing of replacing the lamp When the Lamp indicator light lights up red or a message appears suggesting it is time to replace the lamp, please install a new lamp or consult your dealer. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode. CAUTION The Lamp indicator light and Temperature indicator light will light up if the lamp becomes too hot. Turn the power off and let the projector cool for 45 minutes.
Replacing the lamp Turn the power off and disconnect the projector from the power outlet. Please contact qualified service personnel for changing the lamp.
Indicators Light Status & Description Power events Blue Flashing Off Off Stand-by mode Blue Off Off Blue Off Off Powering up Normal operation Blue Flashing Off Off Normal power-down cooling (3 sec) Red Off Off Downloading Lamp events Blue Flashing Off Red First Lamp-Lit error cooling (60 sec) Off Off Red Blue Off Red Lamp error in normal operation (30 sec) CW start fail (30 sec) Thermal events Off Red Off Off Red Red Off Red Blue Off Red Purple Red Red Red Red
Troubleshooting The projector does not turn on. Cause Remedy There is no power from the power cord. Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on. Attempting to turn the projector on again during the cooling process. Wait until the cooling down process has completed. No picture Cause Remedy The video source is not turned on or connected correctly.
Specifications Projector specifications • All specifications are subject to change without notice. • Not all models can be purchased in your region.
Output terminal RGB output Audio signal output Speaker D-Sub 15-pin (female) x 1 Audio jack x 1 10 watt x 1 Control terminal RS-232 serial control LAN USB serial control IR receiver 9 pin x 1 RJ45 x 1 Type mini B x 1 (Front) Environmental Requirements Operating temperature Operating relative humidity Operating altitude 0°C–40°C at sea level 10%–90% (without condensation) • • 0–1499 m at 5°C–35°C 1500–3000 m at 5°C–25°C (with High Altitude Mode on) 65
Dimensions 315.24 mm (W) x 97.7 mm (H) x 227.93 mm (D) (Excluding extrusions) 227.93 315.24 97.7 Ceiling mount installation 27.13 60.87 63.62 Ceiling mount screws: M4 x 8 (Max. L = 8 mm) 13.00 1.45 198.
Timing chart Analog RGB Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) VGA 640 x 480 4:3 60/72/75/85 SVGA 800 x 600 4:3 60/72/75/85 1024 x 768 4:3 60/70/75/85 1152 x 864 4:3 75 1280 x 768 15:9 60 1280 x 800 16:10 60/75/85 1360 x 768 16:9 60 Quad-VGA 1280 x 960 4:3 60/85 SXGA 1280 x 1024 5:4 60 SXGA+ 1400 x 1050 4:3 60 WXGA+ 1440 x 900 16:10 60 UXGA 1600 x 1200 4:3 60 WSXGA+ 1680 x 1050 16:10 60 HD 1280 x 720 16:9 60 MAC 13" 640 x 480 4:3 67
HDMI Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) VGA 640 x 480 4:3 60 SVGA 800 x 600 4:3 60 XGA 1024 x 768 4:3 60 1280 x 768 15:9 60 1280 x 800 16:10 60 1360 x 768 16:9 60 Quad-VGA 1280 x 960 4:3 60 SXGA 1280 x 1024 5:4 60 SXGA+ 1400 x 1050 4:3 60 WXGA+ 1440 x 900 16:10 60 WSXGA+ 1680 x 1050 16:10 60 HDTV (1080p) 1920 x 1080 16:9 50 / 60 HDTV (1080i) 1920 x 1080 16:9 50 / 60 HDTV (720p) 1280 x 720 16:9 50 / 60 SDTV (480p) 720 x 480 4:3 /
3D (HDMI signal included) Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) SVGA 800 x 600 4:3 60* / 120** XGA 1024 x 768 4:3 60* / 120** HD 1280 x 720 16:9 60* / 120** WXGA 1280 x 800 16:9 60* / 120** Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) SDTV (480i)*** 720 x 480 4:3 / 16:9 60 for Video Signal * 60Hz signals are supported for Side-by-Side, Top-Bottom, and Frame Sequential formats. ** 120 Hz signals are supported for Frame Sequential format only.
Component video Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) HDTV (1080p) 1920 x 1080 16:9 50 / 60 HDTV (1080i) 1920 x 1080 16:9 50 / 60 HDTV (720p) 1280 x 720 16:9 50 / 60 SDTV (480p) 720 x 480 4:3 / 16:9 60 SDTV (576p) 720 x 576 4:3 / 16:9 50 SDTV (480i) 720 x 480 4:3 / 16:9 60 SDTV (576i) 720 x 576 4:3 / 16:9 50 Composite video Signal Aspect Ratio Refresh Rate (Hz) NTSC 4:3 60 PAL 4:3 50 PAL60 4:3 60 SECAM 4:3 50 70
Copyright information Copyright Copyright 2014. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation.
Appendix IR control table Key Format Byte1 Byte2 Byte3 Byte4 PgDn NEC X3 F4 05 FA PgUp NEC X3 F4 06 F9 Blank NEC X3 F4 07 F8 Auto sync NEC X3 F4 08 F7 Up NEC X3 F4 0B F4 Down NEC X3 F4 0C F3 Left NEC X3 F4 0E F1 Right NEC X3 F4 0F F0 Color Mode NEC X3 F4 10 EF Mute NEC X3 F4 14 EB EA Enter NEC X3 F4 15 Power ON NEC X3 F4 17 E8 Presentation Timer NEC X3 F4 27 D8 Exit NEC X3 F4 28 D7 D.
Address code Code 1 83F4 Code 2 93F4 Code 3 A3F4 Code 4 B3F4 Code 5 C3F4 Code 6 D3F4 Code 7 E3F4 Code 8 F3F4 RS232 command table Pin Description Pin 1 NC 2 Description RX 3 TX 4 NC 5 GND 6 NC 7 RTSZ 8 CTSZ 9 NC RS-232 protocol Baud Rate 115200 bps (default) Data Length 8 bit Parity Check None Stop Bit 1 bit Flow Control None 73
Function Statu s Action cmd Turn on 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D Turn off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E Write Power Read Power status (on/off) 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 0x5E Reset all settings Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F Reset Color Settings Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2A 0x00 0x87 Write Splash Screen Read Splash Screen Black 0x06 0x14 0x00 0x04 0x00 0x34
Message Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x00 0x84 Message On 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x01 0x85 Write Message Read Message status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x27 0x85 Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F Rear Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60 Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61 Write Projector Position Read pro
Aspect ratio Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62 Aspect ratio 4:3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64 Aspect ratio 16:9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65 Aspect ratio 16:10 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66 Aspect ratio Anamorphic 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x05 0x67 Aspect ratio Wide 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x06 0x68 Aspect ratio 2.
Blank on 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 0x68 Blank off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x00 0x67 Write Blank Read Blank status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09 0x68 Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68 Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69 Keystone status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A 0x69 Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x00 0x8E Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x11
Saturation decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x00 0x70 Saturation increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x01 0x71 Saturation 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x12 0x71 Write Saturation Read Gain decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71 Gain increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72 Write Gain Read Gain 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13 0x72 Freeze on 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60 Free
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A 0x06 0x14 0x
Write HDMI Format Read Write HDMI Range Read RGB 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x00 0x85 YUV 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x01 0x86 Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x02 0x87 HDMI Format status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x28 0x86 Enhanced 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x00 0x86 Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x01 0x87 Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x02 0x88 HDMI Range status 0x07 0x14 0x00 0x05 0x00
code 1 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x00 0xA0 code 2 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x01 0xA1 code 3 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x02 0xA2 code 4 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x03 0xA3 code 5 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x04 0xA4 code 6 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x05 0xA5 code 7 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x06 0xA6 code 8 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x07 0xA7 Write Remote Control code Read Write S
Remote Key Menu 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0F 0x61 Exit 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x13 0x65 Up 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0B 0x5D Down 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0C 0x5E Left 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0D 0x5F Right 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0E 0x60 Source 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x04 0x56 Enter 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x15 0x67 Auto 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0
Customer Support For technical support or product service, see the table below or contact your reseller. NOTE: You will need the product serial number. Country/Region Website T= Telephone C = CHAT ONLINE Email Australia New Zealand www.viewsonic.com.au AUS= 1800 880 818 NZ= 0800 008 822 service@au.viewsonic.com Canada www.viewsonic.com T= 1-866-463-4775 service.ca@viewsonic.com Europe www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/ Hong Kong www.hk.viewsonic.
Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
How to get service: 1. For information about receiving service under warranty, contact ViewSonic Customer Support (Please refer to Customer Support page). You will need to provide your product's serial number. 2. To obtain warranty service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product. 3.
Mexico Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components & accessories.
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico: Name, address, of manufacturer and importers: México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004 Hermosillo: Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col. Bugambilias C.