Pro8510L/Pro8520WL/Pro8530HDL/ Pro8800WUL DLP Projector User Guide IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service.
Compliance Information FCC Statement This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this unit near water. Clean with a soft, dry cloth. Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, RU RWKHU GHYLFHV LQFOXGLQJ DPSOL¿HUV WKDW SURGXFH KHDW 9.
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Substance Proposed Maximum Concentration Actual Concentration Lead (Pb) 0.1% < 0.
Copyright Information Copyright © ViewSonic® Corporation, 2018. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association.
Table of contents Important safety instructions .......................2 Operating in a high altitude environment ........................................................... 38 Using the CEC function..................... 39 Using the 3D functions ...................... 39 Controlling the projector through a LAN environment ....................................... 40 Using the projector in standby mode ........................................................... 47 Adjusting the sound ........................
Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product. Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Please read this manual before you operate your projector. Save it for future reference. Do not look straight at the projector lens during operation.
13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire. - Do not place this projector on a blanket, bedding or any other soft surface. - Do not cover this projector with a cloth or any other item. - Do not place inflammables near the projector. 14. Always place the projector on a level, horizontal surface during operation.
Introduction Projector features The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use. Some of the features may not be available on your projector. Actual performance may vary and subject to model specifications. • • • • • • • • • • • • • • • • • Power saving function decreasing the power consumption of the lamp by up to 80% when no input signal can be detected for a set period of time.
Controls and functions Projector Lens shift wheel Lamp indicator light Focus and Zoom rings Power indicator light Temperature indicator light • • Power Toggles the projector between standby mode and Power ON. HDMI/MHL port indicator Lights up blue when an HDMI or MHL device is inserted into the inner HDMI/ MHL port. Enter Enacts the selected On-Screen Display (OSD) menu item. • Displays the Corner Adj. page. • Color Mode Selects an available picture setup mode.
Remote control Power HDMI /MHL VIDEO COMP Auto Sync Source Enter Menu Exit Mouse PgUp PgDn Blank Pattern Eco Mode Color Mode Audio Mode To use the remote mouse control keys (Page Up, Page Down, , and ), see "Using the remote mouse control" on page 8 for details. • Power Toggles the projector between standby mode and Power ON. • COMP Selects source from Computer In port for display. • HDMI/MHL Selects source from HDMI/MHL port for display. • VIEDO Selects VIEDO source for display.
• Mouse Switches between the normal and mouse modes. • PgUp, PgDn, , : active after pressing Mouse. An icon appears on the screen to • indicate the activation of the mouse mode. Only available when a PC input signal is selected. • Source Displays the source selection bar. • Laser Emits visible laser pointer light for presentation purposes. • Exit Exits and saves menu settings. • (Right mouse button) Performs the same function as the right mouse button when the mouse mode is activated.
Operating the LASER pointer The Laser Pointer is a presentation aid for professionals. It emits colored light when you press it. The laser beam is visible. It is necessary to press and hold Laser for continuous output. Do not look into the laser light window or shine the laser light beam on yourself or others. See the warning messages on the back of the remote control prior to using it. The laser pointer is not a toy.
• To return to the normal mode, press Mouse again or other keys except for the mouse related multi-function keys. Remote control effective range Refer to the illustration about the location of the InfraRed (IR) remote control sensor(s). The remote control must be held at an angle within 30 degrees perpendicular to the projector's IR remote control sensor(s) to function correctly. The distance between the remote control and the sensor(s) should not exceed 8 meters (~ 26 feet).
Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment. Your projector is designed to be installed in one of the following possible installation locations: 1.
Projection dimensions The "screen" mentioned below refers to the projection screen usually consisting of a screen surface and a support structure. Please see "Projector specifications" on page 83 for the native display resolution of this projector.
4:3 image on a 16:10 Screen (a) Screen Size (b) Projection distance [m (inch)] (c) Image height [inch (cm)] [cm (inch)] min. max. (d) Vertical offset [cm (inch)] min. max. 60 (152) 1.5 (59) 2.4 (94) 81 (32) 6.1 (2.4) 12.1 (4.8) 70 (178) 1.7 (69) 2.8 (110) 94 (37) 7.1 (2.8) 14.1 (5.6) 80 (203) 2.0 (78) 3.2 (126) 108 (42) 8.1 (3.2) 16.2 (6.4) 90 (229) 2.2 (88) 3.6 (141) 121 (48) 9.1 (3.6) 18.2 (7.2) 100 (254) 2.5 (98) 4.0 (157) 135 (53) 10.1 (4.
When the projector’s native resolution is WXGA (1280 x 800) with a throw ratio of 1.12~1.8 16:10 image on a 16:10 Screen (a) Screen Size (b) Projection distance [m (inch)] (c) Image height [inch (cm)] [cm (inch)] min. max. (d) Vertical offset [cm (inch)] min. max. 60 (152) 1.4 (57) 2.3 (91) 81 (32) 4.0 (1.6) 6.1 70 (178) 1.7 (67) 2.7 (106) 94 (37) 4.7 (1.9) 7.1 (2.4) (2.8) 80 (203) 1.9 (76) 3.1 (122) 108 (42) 5.4 (2.1) 8.1 (3.2) 90 (229) 2.2 (86) 3.
When the projector’s native resolution is WUXGA (1920 x 1200) with a throw ratio of 1.07~1.71 16:10 image on a 16:10 Screen (a) Screen Size (b) Projection distance [m (inch)] (c) Image height [inch (cm)] [cm (inch)] min. max. (d) Vertical offset [cm (inch)] min. max. 60 (152) 1.4 (54) 2.2 (87) 75 (29) 1.9 (0.7) 3.7 70 (178) 1.6 (63) 2.6 (101) 87 (34) 2.2 (0.9) 4.4 (1.5) (1.7) 80 (203) 1.8 (72) 2.9 (116) 100 (39) 2.5 (1.0) 5.0 (2.0) 90 (229) 2.1 (81) 3.
For models with a 16:9 native aspect ratio • 16:9 image on a 16:9 screen (a) (b) (e) (a) (f) (d) (c) (c) (d) (f) (b) (e) • 16:9 image on a 4:3 screen (a) (b) (a) (e) (f) (d) (c) (c) (d) (f) (b) (e) (e): Screen (f): Center of lens When the projector’s native resolution is 1080p (1920 x 1080) with a throw ratio of 1.07~1.71 16:9 image on a 16:9 Screen (a) Screen Size (b) Projection distance [m (inch)] (c) Image height [inch (cm)] [cm (inch)] min. max.
16:9 image on a 4:3 Screen (a) Screen Size (b) Projection distance [m (inch)] (c) Image height [inch (cm)] [cm (inch)] min. max. (d) Vertical offset [cm (inch)] min. max. 60 (152) 1.3 (51) 2.1 (82) 69 (27) 5.1 (2.0) 10.3 (4.1) 70 (178) 1.5 (60) 2.4 (96) 80 (32) 6.0 (2.4) 12.0 (4.7) 80 (203) 1.7 (68) 2.8 (110) 91 (36) 6.9 (2.7) 13.7 (5.4) 90 (229) 2.0 (77) 3.1 (123) 103 (41) 7.7 (3.0) 15.4 (6.1) 100 (254) 2.2 (86) 3.5 (137) 114 (45) 8.6 (3.4) 17.
Connection When connecting a signal source to the projector, be sure to: 1. 2. 3. Turn all equipment off before making any connections. Use the correct signal cables for each source. Ensure the cables are firmly inserted. In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 4). They are commercially available from electronics stores. The connection illustrations below are for reference only.
Audio in Audio cable or Computer (for Component signal) Audio cable A/V device VGA cable Computer Out or Monitor VGA to DVI-A cable S-Video connector Video connector Audio in L/R USB 5V/ 2A Out S-Video cable A/V device Video cable A/V device (for S-Video/Video signal) Audio cable A/V device USB Power Charger (This connector may be inside the projector. Open the cover before using.
(Trigger only) 12V Out Powered screen Microphone MIC Audio Out Speakers Connecting a computer or monitor Connecting a computer 1. 2. 3. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer. Connect the other end of the VGA cable to the COMPUTER IN 1 or COMPUTER IN 2 signal input socket on the projector.
The COMPUTER OUT output only works when COMPUTER IN 1 connection is made to the projector in the standby mode. To use this connection method, turn on the Active VGA Out function under the SOURCE > Standby Settings menu.
Connecting an HDMI device You should use an HDMI cable when making connection between the projector and HDMI devices. 1. 2. Take an HDMI cable and connect one end to the HDMI output port of the video device. Connect the other end of the cable to the HDMI input port on the projector. In the unlikely event that you connect the projector to a DVD player via the projector’s HDMI input and the projected picture displays wrong colors, please change the color space to YUV.
Connecting a composite Video source device Examine your Video source device to determine if it has a set of unused composite Video output sockets available: • • 1. 2. If so, you can continue with this procedure. If not, you will need to reassess which method you can use to connect to the device. Take a Video cable and connect one end to the composite Video output socket of the Video source device. Connect the other end of the Video cable to the VIDEO socket on the projector.
The greater volume you require, the greater distance you need to be away from the speaker to prevent the noise. Using the cable management cover This cable management cover helps you to conceal and organize the cables connected to the back of the projector. It is especially useful when the projector is ceiling-mounted or wallmounted. 1. 2. 3. Make sure that all the cables are properly connected to the projector. Attach the cable management cover to the back of the projector.
Operation Starting up the projector 1. 2. 3. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). (If available) Remove the lens cap. Press Power to start the projector. As soon as the lamp lights up, a "Power On Ring Tone" will be heard. The Power indicator light stays blue when the projector is on. (If necessary) Rotate the focus ring to adjust the image clearness.
Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. The OSD screenshots below are for reference only, and may differ from the actual design. Below is the overview of the OSD menu. Main menu icon Highlight Status Sub-menu Go to the previous page or to exit. Current input signal To use the OSD menus, please select your language first. 1. Press Menu to turn the OSD menu on. 3. Press to highlight Language and press Enter. 2.
Utilizing the password function For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on page 25. You will be inconvenienced if you enable the password function yet forget the password somehow. Do make a note of your password, and keep the note in a safe place for later recall.
Entering the password recall procedure 1. 2. 3. Press and hold Auto Sync on the remote control for 3 seconds. The projector will display a coded number on the screen. Write down the number and turn off your projector. Seek help from the local service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector. The "XXX" shown in the above screenshot are numbers that vary depending on different projector models.
Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. Be sure the Quick Auto Search function in the SYSTEM menu is On if you want the projector to automatically search for the signals. You can also manually select the desired signal by pressing one of the source selection keys on the remote control, or cycle through the available input signals. 1. 2. Press Source. A source selection bar is displayed.
Adjusting the projected image Adjusting the projection angle The projector is equipped with 2 adjuster foot. It changes the image height and vertical projection angle. Press the quick-release buttons and lift the front of the projector. Once the image is positioned where you want it, release the quickrelease buttons to lock the foot in position.
Correcting keystone Keystoning refers to the situation where the projected image becomes a trapezoid due to angled projection. To correct this, besides adjusting the height of the projector, you will need to manually correct it following one of these steps. • Using the remote control 1. Press / / / to display the Keystone correction page. 2. Press to correct keystoning at the top of Press / Press / the image. Press to correct keystoning at the bottom of the image.
3. 4. Press / to select an adjustment method that suits your need and press Enter. As indicated on the screen ( / for a 45degree angle adjustment and / / / for a 90-degree angle adjustment), press / / / to adjust its shape and size. You can press Menu or Exit to go back to a previous step. A long press for 2 seconds on Enter will reset the settings on the corner that you chose. Indicates the corner that you selected. Adjusting keystone will reset the Corner Adj. settings. After the Corner Adj.
Selecting the aspect ratio The 'aspect ratio' is the ratio of the image width to the image height. With the advent of digital signal processing, digital display devices like this projector can dynamically stretch and scale the image output to a different aspect than that of the image input signal. To change the projected image ratio (no matter what aspect the source is): 1. 2. 3. Open the OSD menu and go to the DISPLAY > Aspect Ratio menu. Press Enter.
16:9 Not available 16:10 Not available Panorama Not available Not available 2.35:1 Anamorphic Not available Optimizing the image Selecting a picture mode The projector is preset with several predefined picture modes so that you can choose one to suit your operating environment and input signal picture type. To select an operation mode that suits your need, you can follow one of the following steps.
DICOM SIM mode is only for training or reference. It not used for actual diagnosis. DICOM represents for the Digital Imaging and Communications in Medicine. This is a standard created by the American College of Radiology and the National Electrical Manufacturers Association. This standard specifies the method of digital image data to be transferred from one system to another.
Adjusting Sharpness Go to the IMAGE > Advanced > Sharpness menu and press / . The higher the value, the sharper the picture becomes. The lower the value, the softer the picture becomes. This function is only available when the input signal is S-Video, Video, YPbPr (digital) or YCbCr (digital). Adjusting Brilliant Color Go to the IMAGE > Advanced > Brilliant Color menu and press / .
Color Management Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. Color management provides fine color control adjustment to allow for more accurate color reproduction, should you require it. If you have purchased a test disc which contains various color test patterns and can be used to test the color presentation on monitors, TVs, projectors, etc.
2. Press Enter or wait for 3 seconds to activate the timer. 3. To display the Presentation Timer page, select Advanced. • Using the OSD menu 1. Go to the BASIC > Presentation Timer menu. 2. Press Enter to display the Presentation Timer page. 3. Highlight Timer Period and decide the time period by pressing / . The length of time can be set from 1 to 5 minutes in 1-minute increments and 5 to 240 minutes in 5minute increments.
You can set the blank time in the BASIC > Blank Timer menu to let the projector return the image automatically after a period of time when there is no action taken on the blank screen. Once Blank is pressed, the projector enters Eco mode automatically. CAUTION Do not block the projection lens from projecting as this could cause the blocking object to become heated and deformed or even cause a fire.
Do not use the High Altitude Mode if your altitude is between 0 m and 1500 m and temperature is between 5°C and 35°C. The projector will be over cooled, if you turn the mode on under such a condition. To activate the High Altitude Mode: 1. Open the OSD menu and go to the SYSTEM > High Altitude Mode menu. 2. Press Enter and press / to select On. A confirmation message is displayed. 3. Highlight Yes and press Enter.
5. Press to select a 3D Sync setting and then press Enter to confirm. When the 3D Sync function is on: • The brightness level of the projected image will decrease. • The Color Mode cannot be adjusted. • The Zoom function can only magnify the pictures to limited sizes. If you discover the inversion of the 3D image depth, set the 3D Sync Invert function to “Invert” to correct the problem. Controlling the projector through a LAN environment The projector supports Crestron® software.
2. 3. 4. 5. 6. 7. Highlight LAN Control Settings and press / to select Static IP. Contact your ITS administrator for information on the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server settings. Press to select the item you want to modify and press Enter. Press / to move the cursor and the press / to enter the value. To save the settings, press Enter. If you do not want to save the settings, press Exit. Press to highlight Apply and press Enter.
controllers of AMX connected to the same network. For the Details of AMX Device Discovery, visit the AMX web site at http://www.amx.com/. 4. If your projector is connected to a network which supports Simple Mail Transfer Protocol (SMTP), you can configure it to alert you via email on significant events. 5. The Crestron (e-Control) page displays the Crestron e-Control user interface. See "About Crestron e-Control®" on page 44 for details.
Please pay attention to the limitation of input length (including space and other punctuation keys) in the list blow: Category Item Network Input Length Maximum Number of Characters DHCP/Manual (N/A) IP Address XXX.XXX.XXX.XXX Subnet Mask XXX.XXX.XXX.XXX Gateway XXX.XXX.XXX.XXX DNS Server XXX.XXX.XXX.XXX AMX device discovery (N/A) Network Settings Password SNMP Email Setting SMTP Setting Email Alert Alert Condition / > < $ % + \ ' " are prohibited.
About Crestron e-Control® 1. The Crestron e-Control® page provides a variety of virtual keys to control the projector or adjust the projected pictures. i ii i You can press / to reveal more buttons. i i. These buttons function the same as the ones on the OSD menus or remote control. See "2. IMAGE menu" on page 55 and "Projector" on page 7 for details. ii. To switch between input signals, click on your desired signal.
iii. You can adjust the LAN Control Settings. iv. Once set, access to the remote network operation on this projector has been password-protected. v. Once set, access to the tools page has been password-protected. To prevent errors, only input the English alphabet and digits on the tools page. After making the adjustments, press the Send button and the data will be saved for the projector. vi. Press Exit to go back to the remote network operation page.
3. The info page displays the information and status of this projector. Press Exit to go back to the remote network operation page. 4. After pressing the button “Contact IT Help”, the HELP DESK window will appear in the upper right corner of the screen. You will be able to deliver messages to RoomView™ software administrators/users who connect to the same local area network. For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
PJLink™, SNMP, AMX and Xpanel formats supported This projector is PJLink™, SNMP V.1, AMX or Xpanel V1.10 compliant. For details, please follow its user guide or website respectively to control and manage projectors. Using the projector in standby mode Some of the projector functions are available in standby mode (plugged in but not turned on). To use these functions, be sure the cable connections are correctly made. For the connection methods, see the Connection chapter.
Adjusting the Audio In 2 setting 1. 2. Open the OSD menu and go to the BASIC > Audio Settings > Audio In 2 menu. Press / to decide the audio input source for the AUDIO IN 2/MIC port. This will affect the connection method for different devices, and where the sound is from. • When Audio is selected: Device COMPUTER IN 1 COMPUTER IN 2 Video/S-Video AUDIO IN 1 AUDIO IN 2 AUDIO IN 2 The projector can play AUDIO IN 1 the sound from...
Shutting down the projector 1. Press Power and a confirmation message is displayed prompting you. If you don't respond in a few seconds, the message will disappear. 2. 3. Press Power a second time. Once the cooling process finishes, a "Power Off Ring Tone" will be heard. Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time. To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 48 for details.
Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible. Main menu Sub-menu Options Screen Color Off/Blackboard/Greenboard/Whiteboard Auto/4:3/16:9/16:10/Panorama/2.35:1/ Anamorphic Aspect Ratio Keystone 1. DISPLAY Corner Adj. Position Phase H.
Main menu Sub-menu Computer Auto Power On CEC Direct Power On Auto Power Off Smart Energy 3. POWER MANAGEMENT MHL Settings Standby Settings Sleep Timer Power Saving Power Out MHL Reset Active VGA Out Active Audio Out Audio Mode Mute Audio Volume Audio Settings Audio In 2 Microphone Volume Power On/Off Ring Tone Timer Period Timer Display 4.
Main menu 4. BASIC Sub-menu My Button 3D Settings HDMI Settings 5. ADVANCED LAN Control Settings Lamp Settings Filter Settings DCR Closed Caption Reset Settings Options Auto/Projection (Projector Position)/Menu Position/Color Temp.
Main menu Sub-menu Options Multi-language OSD selection Front Table/Rear Table/ Projector Position Rear Ceiling/Front Ceiling 5 sec/10 sec/15 sec/20 Menu Display Time sec/25 sec/30 sec Menu Settings Center/Top-Left/Top6. SYSTEM Menu Position Right/Bottom-Left/ Bottom-Right High Altitude Mode On/Off Quick Auto Search Off/On Change Password Security Settings Power On Lock Off/On Panel Key Lock Off/On Remote Control Code 1/2/3/4/5/6/7/8 • Source • Color Mode • Resolution 7.
Description of each menu Function Description Screen Color See "Using Screen Color" on page 34 for details. Aspect Ratio See "Selecting the aspect ratio" on page 32 for details. Keystone See "Correcting keystone" on page 30 for details. Corner Adj. 1. DISPLAY menu Position See "Adjusting 4 corners" on page 30 for details. Displays the position adjustment page. To move the projected image, use the directional arrow keys.
Function Description Color Mode See "Selecting a picture mode" on page 33 for details. Brightness See "Adjusting Brightness" on page 34 for details. Contrast See "Adjusting Contrast" on page 34 for details. Color Temp. 2. IMAGE menu See "Selecting a Color Temperature" on page 35 and "Setting a preferred color temperature" on page 35 for details. Color See "Adjusting Color" on page 34 for details. Tint See "Adjusting Tint" on page 34 for details.
Function Description Computer Selecting Enable allows the projector to turn on automatically once the VGA signal is fed through the VGA cable. Auto Power On 3. POWER MANAGEMENT menu Smart Energy MHL Settings CEC See "Using the CEC function" on page 39 for details. Direct Power On Selecting On allows the projector to turn on automatically once the power is fed through the power cord. Auto Power Off See "Setting Auto Power Off" on page 61 for details.
Function Description 3D Settings See "Using the 3D functions" on page 39 for details. HDMI Settings See "Changing HDMI input settings" on page 28 for details. LAN Control Settings See "Controlling the projector through a LAN environment" on page 40 for details. Lamp Mode See "Setting Lamp Mode" on page 61 for details. Lamp Settings Filter Settings Reset Lamp Hours Resets the lamp timer after new lamp is installed. For changing the lamp, please contact qualified service personnel. 5.
Function Description Language Sets the language for the On-Screen Display (OSD) menus. See "Using the menus" on page 25 for details. Projector Position See "Choosing a location" on page 10 for details. 6. SYSTEM menu Menu Settings Menu Display Time Sets the length of time the OSD will remain active after your last key press. The range is from 5 to 30 seconds in 5-second increments. Menu Position Sets the On-Screen Display (OSD) menu position.
Maintenance Care of the projector You need to keep the lens and/or filter (optional accessory) clean on a regular basis. Never remove any parts of the projector. Contact your dealer when any part of the projector needs replacing. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface. • • Use a canister of compressed air to remove dust. If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface.
• If your projector is ceiling-mounted or is not easily accessible, pay special attention to your personal safety when replacing the dust filter. Installing the dust filter 1. 2. Be sure to turn off the projector and unplug it from power source. As the arrows shown to the right, fit the filter by aligning and inserting it into the projector slots. Make sure it clicks into place. For first time installation: 3. Open the OSD menu and go to the ADVANCED > Filter Settings menu. 4.
The timer will continue counting the next time you fit the filter back on and set Filter Mode to On. Lamp information Getting to know the lamp hour When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. To obtain the lamp hour information: 1. Open the OSD menu and go to the ADVANCED > Lamp Settings menu. 2. Press Enter and the Lamp Settings page is displayed. 3. You will see the Lamp Hours information on the menu. 4.
1. 2. 3. 4. Open the OSD menu and go to the POWER MANAGEMENT > Smart Energy menu. Press Enter and the Smart Energy page is displayed. Highlight Power Saving and press / . When Enable is selected, the projector lamp will be changed to Eco mode after no signal is detected for 5 minutes. Timing of replacing the lamp Please install a new lamp or consult your dealer when the Lamp indicator light lights up. An old lamp may cause a malfunction in the projector and in some instances the lamp may explode.
3. Remove the lamp cover from the projector. 2 WARNING • Do not turn the power on with the lamp cover removed. • Do not insert your fingers between the lamp and the projector. The sharp edges inside the projector may cause injuries. 4. Loosen the screw that secures the lamp. 5. Lift the handle so that it stands up. Use the handle to slowly pull the lamp out of the projector. 1 2 CAUTION • 1 Pulling it too quickly may cause the lamp to break and scatter broken glass in the projector.
7. Tighten the screw that secures the lamp. CAUTION • Loose screw may cause a bad connection, which could result in malfunction. • Do not over tighten the screw. 8. Ensure the handle is fully laid flat and locked in place. 9. Replace the lamp cover on the projector. 10. Tighten the screws that secure the lamp cover. CAUTION • Loose screw may cause a bad connection, which could result in malfunction. • Do not over tighten the screws.
Indicators Light Status & Description Power events Blue Flashing Off Off Stand-by mode Blue Off Off Blue Off Off Powering up Normal operation Blue Flashing Off Off Normal power-down cooling (3 sec) Downloading Burn in off Red Off Off Blue Blue Blue Lamp events Blue Flashing Off Red First Lamp-Lit error cooling (60 sec) Off Off Red Blue Off Red Lamp error in normal operation (30 sec) CW start fail (30 sec) Thermal events Off Red Off Off Red Red Off Red Blue Off Red
Troubleshooting The projector does not turn on. Cause Remedy There is no power from the power cord. Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on. Attempting to turn the projector on again during the cooling process. Wait until the cooling down process has completed. No picture Cause Remedy The video source is not turned on or connected correctly.
Specifications Dimensions 469.5 mm (W) x 139.8 mm (H) x 316.24 mm (D) (Including extrusions) FOCUS ZOOM 469.5 316.24 139.8 Ceiling mount installation 133.10 8.16 164.10 Ceiling mount screws: M4 x 8 (Max. L = 8 mm) 3.50 286.20 Unit: mm 291.
IR control table Key Format Byte1 Byte2 Byte3 Byte4 PgDn NEC X3 F4 05 FA PgUp NEC X3 F4 06 F9 Blank NEC X3 F4 07 F8 Auto sync NEC X3 F4 08 F7 Up NEC X3 F4 0B F4 Down NEC X3 F4 0C F3 Left NEC X3 F4 0E F1 Right NEC X3 F4 0F F0 Color Mode NEC X3 F4 10 EF Mute NEC X3 F4 14 EB EA Enter NEC X3 F4 15 Power ON NEC X3 F4 17 E8 Presentation Timer NEC X3 F4 27 D8 D7 Exit NEC X3 F4 28 Eco Mode NEC X3 F4 2B D4 Menu NEC X3 F4
Address code Code 1 83F4 Code 2 93F4 Code 3 A3F4 Code 4 B3F4 Code 5 C3F4 Code 6 D3F4 Code 7 E3F4 Code 8 F3F4 RS232 command table Pin Description Pin 1 NC 2 Description RX 3 TX 4 NC 5 GND 6 NC 7 RTSZ 8 CTSZ 9 NC RS-232 protocol Baud Rate 115200 bps (default) Data Length 8 bit Parity Check None Stop Bit 1 bit Flow Control None 69
Message Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x00 0x84 Message On 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x27 0x01 0x85 Write Message Read Message status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x27 0x85 Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F Rear Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60 Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61 Write Projector Position Read pro
Write Aspect ratio Read Auto Adjust Aspect ratio Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62 Aspect ratio 4:3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64 Aspect ratio 16:9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65 Aspect ratio 16:10 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66 Aspect ratio Anamorphic 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x05 0x67 Aspect ratio 2.
Blank on 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x01 0x68 Blank off 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x09 0x00 0x67 Write Blank Read Blank status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x09 0x68 Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68 Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69 Keystone status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A 0x69 Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x00 0x8E Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x11
Saturation decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x00 0x70 Saturation increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x12 0x01 0x71 Saturation 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x12 0x71 Write Saturation Read Gain decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71 Gain increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72 Write Gain Read Gain 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13 0x72 Freeze on 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60 Free
Increase Volume 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x01 0x00 0x61 Decrease Volume 0x06 0x14 0x00 0x04 0x00 0x34 0x14 0x02 0x00 0x62 Write Volume Read Volume 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x14 0x03 0x64 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05
Write Reset Lamp usage hour 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x01 0x00 0x62 Read Lamp usage hour 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x15 0x01 0x63 Lamp Time Write HDMI Format Read Write HDMI Range Read RGB 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x00 0x85 YUV 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x01 0x86 Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x02 0x87 HDMI Format status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x28 0x86 Enhanced 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29
Write Brilliant Color Read Brilliant Color 0 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x00 0x6D Brilliant Color 1 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x01 0x6E Brilliant Color 2 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x02 0x6F Brilliant Color 3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x03 0x70 Brilliant Color 4 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x04 0x71 Brilliant Color 5 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x05 0x72 Brilliant Color 6 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0F 0x06
Write Screen Color Read Screen color Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x00 0x8F Blackboard 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x01 0x90 Greenboard 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x02 0x91 Whiteboard 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x32 0x03 0x92 Screen Color status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x32 0x90 Overscan Off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x00 0x90 Overscan 1 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x33 0x01 0x91 Overscan 2 0x06 0x14 0
Timing chart Analog RGB Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) VGA 640 x 480 4:3 60/72/75/85 SVGA 800 x 600 4:3 60/72/75/85 1024 x 768 4:3 60/70/75/85 1152 x 864 4:3 75 1280 x 768 15:9 60 1280 x 800 16:10 60/75/85 1360 x 768 16:9 60 Quad-VGA 1280 x 960 4:3 60/85 SXGA 1280 x 1024 5:4 60 SXGA+ 1400 x 1050 4:3 60 WXGA+ 1440 x 900 16:10 60 UXGA 1600 x 1200 4:3 60 WSXGA+ 1680 x 1050 16:10 60 HD 1280 x 720 16:9 60 MAC 13" 640 x 480 4:3 67
HDMI Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) VGA 640 x 480 4:3 60 SVGA 800 x 600 4:3 60 XGA 1024 x 768 4:3 60 1280 x 768 15:9 60 1280 x 800 16:10 60 1360 x 768 16:9 60 Quad-VGA 1280 x 960 4:3 60 SXGA 1280 x 1024 5:4 60 SXGA+ 1400 x 1050 4:3 60 WXGA+ 1440 x 900 16:10 60 WSXGA+ 1680 x 1050 16:10 60 HDTV (1080p) 1920 x 1080 16:9 50 / 60 HDTV (1080i) 1920 x 1080 16:9 50 / 60 HDTV (720p) 1280 x 720 16:9 50 / 60 SDTV (480p) 720 x 480 4:3 /
3D (HDMI signal included) Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) SVGA 800 x 600 4:3 60* / 120** XGA 1024 x 768 4:3 60* / 120** HD 1280 x 720 16:9 60* / 120** WXGA 1280 x 800 16:9 60* / 120** Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) SDTV (480i)*** 720 x 480 4:3 / 16:9 60 for Video Signal * 60Hz signals are supported for Side-by-Side, Top-Bottom, and Frame Sequential formats. ** 120 Hz signals are supported for Frame Sequential format only.
Component video Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) HDTV (1080p) 1920 x 1080 16:9 50 / 60 HDTV (1080i) 1920 x 1080 16:9 50 / 60 HDTV (720p) 1280 x 720 16:9 50 / 60 SDTV (480p) 720 x 480 4:3 / 16:9 60 SDTV (576p) 720 x 576 4:3 / 16:9 50 SDTV (480i) 720 x 480 4:3 / 16:9 60 SDTV (576i) 720 x 576 4:3 / 16:9 50 Composite video Signal Aspect Ratio Refresh Rate (Hz) NTSC 4:3 60 PAL 4:3 50 PAL60 4:3 60 SECAM 4:3 50 82
Projector specifications All specifications are subject to change without notice. Not all models can be purchased in your region. Model name Pro8510L Pro8520WL Pro8530HDL Pro8800WUL Product Specification Resolution Throw ratio Display system Lamp Type 0.55” XGA 0.65” WXGA 0.65” 1080p 0.67” WUXGA (1024 x 768) (1280 x 800) (1920 x 1080) (1920 x 1200) 1.41~2.25 1.12~1.8 1.07~1.
Environmental Requirements Operating Temperature Operating Altitude 0°C–40°C at sea level 0–1499 m at 5°C–35°C 1500–3000 m at 5°C–25°C (with High Altitude Mode on) Operating Relative Humidity 10%–90% (without condensation) 84
Copyright information Copyright Copyright 2016. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation.
Customer Support For technical support or product service, see the table below or contact your reseller. Note : You will need the product serial number. Website T= Telephone C = CHAT ONLINE Email www.viewsonic.com.au AUS= 1800 880 818 NZ= 0800 008 822 service@au.viewsonic.com Canada www.viewsonic.com T= 1-866-463-4775 service.ca@viewsonic.com Europe www.viewsoniceurope.com www.viewsoniceurope.com/uk/support/call-desk/ Country/Region Australia New Zealand Hong Kong www.hk.viewsonic.
Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
How to get service: 1. For information about receiving service under warranty, contact ViewSonic Customer Support (please refer to “Customer Support” page). You will need to provide your product’s serial number. 2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product. 3.
Mexico Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components & accessories.
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico: Name, address, of manufacturer and importers: México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004 Hermosillo: Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col. Bugambilias C.