PS500X/PS501X/PS600X/PS501W/ PS600W DLP Projector User Guide IMPORTANT: Please read this User Guide to obtain important information on installing and using your product in a safe manner, as well as registering your product for future service.
Compliance Information FCC Statement This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. "" "' 13. "; Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this unit near water. Clean with a soft, dry cloth. Do not block any ventilation openings. Install the unit in accordance with the manufacturer’s instructions.
Declaration of RoHS2 Compliance This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below: Substance Proposed Maximum Concentration Actual Concentration Lead (Pb) 0.1% < 0.
Copyright Information Copyright © ViewSonic® Corporation, 2018. All rights reserved. Macintosh and Power Macintosh are registered trademarks of Apple Inc. Microsoft, Windows, Windows NT, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries. ViewSonic, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic Corporation. VESA is a registered trademark of the Video Electronics Standards Association.
Table of contents Important safety instructions .......................2 Controlling the projector through a LAN environment (PS600W/PS600X)....... 36 Using the projector in standby mode. 43 Adjusting the sound ........................... 43 Shutting down the projector .............. 44 Menu operation.................................. 45 Introduction......................5 Projector features ................................. 5 Shipping contents................................. 6 Controls and functions ...
Important safety instructions Your projector is designed and tested to meet the latest standards for safety of information technology equipment. However, to ensure safe use of this product, it is important that you follow the instructions mentioned in this manual and marked on the product. Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Please read this manual before you operate your projector. Save it for future reference. Do not look straight at the projector lens during operation.
13. Do not block the ventilation holes. If the ventilation holes are seriously obstructed, overheating inside the projector may result in a fire. - Do not place this projector on a blanket, bedding or any other soft surface. - Do not cover this projector with a cloth or any other item. - Do not place inflammables near the projector. 14. Always place the projector on a level, horizontal surface during operation.
will perform the secondary role of restraining the projector should its attachment to the mounting bracket become loose.
Introduction Projector features The projector integrates high-performance optical engine projection and a user-friendly design to deliver high reliability and ease of use. Some of the features may not be available on your projector. Actual performance may vary and subject to model specifications. • • • • • • • • • • • • • • • • • Power saving function decreasing the power consumption of the lamp by up to 70% when no input signal can be detected for a set period of time.
Shipping contents 1. Projector 4. 6. Quick Start Guide 5. Remote Control & Batteries Replacement lamp (optional) (Please contact qualified service personnel for changing the lamp) Dust filter (optional) 7. 2. 6 Power Cord 3.
Controls and functions Projector Power indicator light Temperature indicator light Lamp indicator light PS501W/PS501X/PS500X Power indicator light Temperature indicator light Lamp indicator light PS600W/PS600X Vent (heated air exhaust) Focus ring Projection lens IR remote sensor • • Power Toggles the projector between standby mode and Power ON. / / / (Keystone keys) Manually corrects distorted images resulting from an angled projection. • Source Displays the source selection bar.
1 2 3 1 2 3 4 5 6 7 8 9 10 6 7 8 5 10 11 6 7 85 PS600W/PS600X PS501W/PS501X 1 2 PS500X Kensington anti-theft lock slot AC power cord inlet Security bar for anti-theft lock slot Ceiling mount holes Adjuster foot Interactive module mounting 1. 2. 3. 4. 5. 6. AUDIO IN Audio signal input socket. AUDIO OUT Audio signal output socket. HDMI HDMI port. USB 5V/1A Out USB Type A port for power supply. Mini USB Mini USB port.
Remote control PS600W/PS600X PS501W/PS501X/PS500X To use the remote mouse control keys (Page Up, Page Down), see "Using the remote PgUp/PgDn function" on page 11 for details. • On/ Off Toggles the projector between standby mode and Power ON. • VIDEO Selects source from VIDEO or SVIDEO port for display. • COMP Selects source from COMPUTER port for display. • • HDMI Selects source from HDMI port for display. Auto Sync Automatically determines the best picture timings for the displayed image.
• • Displays the Corner Adj. page. • Left/ Right/ Up/ Down Selects the desired menu items and makes • adjustments. • Menu Turns on the On-Screen Display (OSD) menu. • Exit Exits and saves menu settings. • (Presentation Timer) Displays the presentation timer settings menu. Eco Mode Displays the lamp mode selection bar. • (Volume Up) Increases the volume level. • (Volume Down) Decreases the volume level. (Laser) Emits visible laser pointer light for presentation purposes.
If different codes are set on the projector and remote control, there will be no response from the remote control. When that happens, a message will display to remind you to switch the code for the remote control. Using the remote PgUp/PgDn function The capability of operating your computer with the remote control gives you more flexibility when delivering presentations. 1. 2. 3. Set the input signal to a PC signal.
• Dispose of the used batteries according to the manufacturer's instructions and local environment regulations for your region. • Never throw the batteries into a fire. There may be danger of an explosion. • If the batteries are drained or if you will not be using the remote control for an extended period of time, remove the batteries to avoid damage to the remote control from possible battery leakage.
Positioning your projector Choosing a location Your room layout or personal preference will dictate which installation location you select. Take into consideration the size and position of your screen, the location of a suitable power outlet, as well as the location and distance between the projector and the rest of your equipment. Your projector is designed to be installed in one of the following possible installation locations: 1.
Projection dimensions The "screen" mentioned below refers to the projection screen usually consisting of a screen surface and a support structure. Please see "Projector specifications" on page 77 for the native display resolution of this projector.
PS600W/PS501W • 16:10 image on a 16:10 screen (b) (a) (a) (e) (d) (f) (c) (c) (d) (f) (b) (e) • 16:10 image on a 4:3 screen (b) (a) (a) (e) (f) (d) (c) (c) (d) (f) (b) (e) (e): Screen (f): Center of lens 16:10 image on a 16:10 Screen (a) Screen Size [inch (m)] (b) Projection distance [m (inch)] (c) Image height [cm (inch)] (d) Vertical offset [cm (inch)] 16:10 image on a 4:3 Screen (b) Projection distance [m (inch)] (c) Image height [cm (inch)] (d) Vertical offset [cm (inch)]
Connection When connecting a signal source to the projector, be sure to: 1. 2. 3. Turn all equipment off before making any connections. Use the correct signal cables for each source. Ensure the cables are firmly inserted. In the connections shown below, some cables may not be included with the projector (see "Shipping contents" on page 6). They are commercially available from electronics stores. The connection illustrations below are for reference only.
PS500X PS501W/PS501X Connecting a computer or monitor Hi:Jml ® HIGH-DEFINITION MULTIMEDIA INTERFACE Connecting a computer 1. 2. Take the supplied VGA cable and connect one end to the D-Sub output socket of the computer. Connect the other end of the VGA cable to the COMPUTER signal input socket on the projector.
3. If you wish to use the remote mouse control function, take a USB cable and connect the larger end to the USB port of the computer, and smaller end to the Mini USB socket on the projector. See "Using the remote PgUp/PgDn function" on page 11 for details. Many notebooks do not turn on their external video ports when connected to a projector. Usually a key combo like FN + F3 or CRT/LCD key turns the external display on/off.
Composite Video is an analog video and will result in a perfectly acceptable, but less than optimal result from your projector, being the least video quality of the available methods described here. See "Connecting a composite Video source device" on page 19 for how to connect the projector to a composite Video device. Connecting audio You can make use of the projector speaker in your presentations, and also connect separate amplified speakers to the Audio Out socket of the projector.
You need only connect to this device using a composite Video connection if Component Video input is unavailable for use. See "Connecting Video source devices" on page 18 for details. Playing sound through the projector You can make use of the projector speaker in your presentations, and also connect separate amplified speakers to the AUDIO OUT socket of the projector.
Operation Starting up the projector 1. Plug the power cord into the projector and into a wall socket. Turn on the wall socket switch (where fitted). 2. Press Power to start the projector. As soon as the lamp lights up, a "Power On Ring Tone" will be heard. The Power indicator light stays blue when the projector is on. (If necessary) Rotate the focus ring to adjust the image clearness.
Using the menus The projector is equipped with On-Screen Display (OSD) menus for making various adjustments and settings. The OSD screenshots below are for reference only, and may differ from the actual design. Below is the overview of the OSD menu. Main menu icon Highlight Status Sub-menu Go to the previous page or to exit. Current input signal To use the OSD menus, please select your language first. 1. Press Menu to turn the OSD menu on. 3. Press to highlight Language and press Enter. 2.
Utilizing the password function For security purposes and to help prevent unauthorized use, the projector includes an option for setting up password security. The password can be set through the On-Screen Display (OSD) menu. For details of the OSD menu operation, please refer to "Using the menus" on page 22. You will be inconvenienced if you enable the password function yet forget the password somehow. Do make a note of your password, and keep the note in a safe place for later recall.
Entering the password recall procedure 1. 2. 3. Press and hold Auto Sync on the remote control for 3 seconds. The projector will display a coded number on the screen. Write down the number and turn off your projector. Seek help from the local service center to decode the number. You may be required to provide proof of purchase documentation to verify that you are an authorized user of the projector. The "XXX" shown in the above screenshot are numbers that vary depending on different projector models.
Switching input signal The projector can be connected to multiple devices at the same time. However, it can only display one full screen at a time. Be sure the Quick Auto Search function in the SYSTEM menu is On if you want the projector to automatically search for the signals. You can also manually select the desired signal by pressing one of the source selection keys on the remote control, or cycle through the available input signals. 1. 2. Press Source. A source selection bar is displayed.
Adjusting the projected image Adjusting the projection angle The projector is equipped with an adjuster foot. It changes the image height and vertical projection angle. Screw the adjuster foot to fine tune the angle until the image is positioned where you want it. If the projector is not placed on a flat surface or the screen and the projector are not perpendicular to each other, the projected image becomes trapezoidal. To correct this situation, see "Correcting keystone" on page 26 for details.
2. 3. Press Enter. Press to correct keystoning at the top of the image or press to correct keystoning at the bottom of the image. Press to correct keystoning at the right side of the image. Press to correct keystoning at the left side of the image. Adjusting 4 corners (PS600W/PS600X) You can manually adjusts the shape and size of an image that is unevenly rectangular on all sides. 1. 2. 3. 4. To display the Corner Adj. page, you can do one of the followings: i. Press Enter. ii.
1. 2. 3. Press on the remote control repeatedly to magnify the picture to a desired size. Press the directional arrows ( , , , ) to navigate the picture. To reduce size of the picture, you can press Auto Sync on the remote control to restore the picture to its original size. Or you can press repeatedly. • Using the OSD menu 1. Open the OSD menu and go to the DISPLAY > Zoom menu. 2. Press Enter. The Zoom bar is displayed. 3. Repeat steps 2-3 in the section of Using the remote control above.
The table below demonstrates the effects of the aspect ratio settings on projectors with different native resolutions. Please see "Projector specifications" on page 77 for the native display resolution of your projector. In the pictures below, the black portions are inactive areas and the white portions are active areas. OSD menus can be displayed on those unused black areas. Aspect ratio setting When the native aspect ratio of your projector is...
The picture modes available for different types of signals are listed below. 1. 2. 3. 4. 5. Brightest mode: Maximizes the brightness of the projected image. This mode is suitable for environments where extra-high brightness is required, such as using the projector in well lit rooms. Presentation mode: Is designed for presentations under daylight environment to match PC and notebook coloring. Standard mode: Is designed for normal circumstances under daylight environment.
The higher the value, the more greenish the picture becomes. The lower the value, the more reddish the picture becomes. This function is only available when the input signal is Video, YPbPr or YCbCr. Adjusting Sharpness Go to the IMAGE > Advanced > Sharpness menu and press / . The higher the value, the sharper the picture becomes. The lower the value, the softer the picture becomes. This function is only available when the input signal is Video, YPbPr or YCbCr.
• Red Offset/Green Offset/Blue Offset: Adjusts the brightness levels of Red, Green, and Blue. This function is only available for PC timings from a VGA or HDMI input signal. Color Management Only in permanent installations with controlled lighting levels such as boardrooms, lecture theaters, or home theaters, should color management be considered. Color management provides fine color control adjustment to allow for more accurate color reproduction, should you require it.
• Using the remote control (if available) 1. Press on the remote control and press repeatedly or / to select a Timer Period. Press Enter or wait for 3 seconds to activate the timer. To display the Presentation Timer page, select Advanced. Using the OSD menu Go to the BASIC > Presentation Timer menu. Press Enter to display the Presentation Timer page. Highlight Timer Period and decide the time period by pressing / .
Hiding the image In order to draw the audience's full attention to the presenter, you can press Blank on the projector or remote control to hide the screen image. Press any key on the projector or remote control to restore the image. The word 'BLANK' appears at the lower right corner of the screen while the image is hidden. You can set the blank time in the BASIC > Blank Timer menu to let the projector return the image automatically after a period of time when there is no action taken on the blank screen.
If you use this projector under other extreme conditions excluding the above, it may display auto shut-down symptoms, which is designed to protect your projector from over-heating. In cases like this, you should switch to High Altitude Mode to solve these symptoms. However, this is not to state that this projector can operate under any and all harsh or extreme conditions.
Controlling the projector through a LAN environment (PS600W/PS600X) The projector supports Crestron® software. With correct settings for the LAN Control Settings menu, you can manage the projector from a computer using a web browser when the computer and the projector are properly connected to the same local area network. IN (An example of connection) Configuring the LAN Control Settings If you are in a DHCP environment: 1. 2. 3. 4. 5.
5. 6. 7. Press / to move the cursor and the press / to enter the value. You can also use the numeric buttons on the remote control to enter the value. To save the settings, press Enter. If you do not want to save the settings, press Exit. Press to highlight Apply and press Enter. If the RJ45 cables are not properly connected, the Projector IP Address, Subnet Mask, Default Gateway, and DNS Server settings will display 0.0.0.0.
controllers of AMX connected to the same network. For the Details of AMX Device Discovery, visit the AMX web site at http://www.amx.com/. 4. If your projector is connected to a network which supports Simple Mail Transfer Protocol (SMTP), you can configure it to alert you via email on significant events. 5. The Crestron (e-Control) page displays the Crestron e-Control user interface. See "About Crestron e-Control®" on page 40 for details.
Please pay attention to the limitation of input length (including space and other punctuation keys) in the list blow: Category Item Network Input Length Maximum Number of Characters DHCP/Manual (N/A) IP Address XXX.XXX.XXX.XXX Subnet Mask XXX.XXX.XXX.XXX Gateway XXX.XXX.XXX.XXX DNS Server XXX.XXX.XXX.XXX AMX device discovery (N/A) Network Settings Password SNMP Email Setting SMTP Setting Email Alert Alert Condition / > < $ % + \ ' " are prohibited.
About Crestron e-Control® 1. The Crestron e-Control® page provides a variety of virtual keys to control the projector or adjust the projected pictures. i ii i You can press / to reveal more buttons. i i. These buttons function the same as the ones on the OSD menus or remote control. See "2. IMAGE menu" on page 50 and "Projector" on page 7 for details. ii. To switch between input signals, click on your desired signal.
iii. You can adjust the LAN Control Settings. iv. Once set, access to the remote network operation on this projector has been password-protected. v. Once set, access to the tools page has been password-protected. To prevent errors, only input the English alphabet and digits on the tools page. After making the adjustments, press the Send button and the data will be saved for the projector. vi. Press Exit to go back to the remote network operation page.
3. The info page displays the information and status of this projector. Press Exit to go back to the remote network operation page. 4. After pressing the button “Contact IT Help”, the HELP DESK window will appear in the upper right corner of the screen. You will be able to deliver messages to RoomView™ software administrators/users who connect to the same local area network. For more information, visit http://www.crestron.com & www.crestron.com/getroomview.
Using the projector in standby mode Some of the projector functions are available in standby mode (plugged in but not turned on). To use these functions, be sure the cable connections are correctly made. For the connection methods, see the Connection chapter. Active VGA Out Selecting On in the POWER MANAGEMENT > Standby Settings > Active VGA Out outputs a VGA signal when the Computer 1 and Monitor Out sockets are correctly connected to devices. The projector outputs the signal received only from Computer 1.
Shutting down the projector 1. Press Power or Off and a confirmation message is displayed prompting you. If you don't respond in a few seconds, the message will disappear. 2. 3. Press Power or Off a second time. Once the cooling process finishes, a "Power Off Ring Tone" will be heard. Disconnect the power cord from the wall socket if the projector will not be used in an extended period of time. • To turn off the ring tone, see "Turning off the Power On/Off Ring Tone" on page 43 for details.
Menu operation Menu system Please note that the on-screen display (OSD) menus vary according to the signal type selected. The menu items are available when the projector detects at least one valid signal. If there is no equipment connected to the projector or no signal detected, limited menu items are accessible. Main menu Sub-menu Options Screen Color 1. DISPLAY 2.
Main menu Sub-menu Signal Auto Power On CEC Direct Power On Auto Power Off Smart Energy 3. POWER MANAGEMENT Standby Settings Sleep Timer Power Saving Active VGA Out Active Audio Out Smart Restart Quick Power Off Mute Audio Volume Audio Settings Power On/Off Ring Tone Timer Period Timer Display 4.
Main menu Sub-menu 3D Settings HDMI Settings 5. ADVANCED LAN Control Settings (PS600W/ PS600X) 3D Sync 3D Sync Invert HDMI Format HDMI Range LAN Settings Projector IP Address Subnet Mask Default Gateway DNS Server Standby LAN control Apply Lamp Mode Lamp Settings Filter Settings Reset Lamp Hours Lamp Hours Filter Mode Reset Filter Hours Filter Hours DCR 6.
Main menu • • • • 7.
Description of each menu Function Description Screen Color See "Using Screen Color" on page 30 for details. Aspect Ratio See "Selecting the aspect ratio" on page 28 for details. Keystone See "Correcting keystone" on page 26 for details. Corner Adj. Position See "Adjusting 4 corners (PS600W/PS600X)" on page 27 for details. Displays the position adjustment page. To move the projected image, use the directional arrow keys.
Function Description Color Mode See "Selecting a picture mode" on page 29 for details. Brightness See "Adjusting Brightness" on page 30 for details. Contrast See "Adjusting Contrast" on page 30 for details. Color Temp. 2. IMAGE menu See "Selecting a Color Temperature" on page 31 and "Setting a preferred color temperature" on page 31 for details. Color See "Adjusting Color" on page 30 for details. Tint See "Adjusting Tint" on page 30 for details.
Function Auto Power On Description Signal Selecting VGA/HDMI allows the projector to turn on automatically once the VGA/HDMI signal is fed through the VGA/HDMI cable. You can also select All and the projector will turn on automatically upon receiving either a VGA or HDMI signal. CEC See "Using the CEC function" on page 35 for details. Direct Power On Selecting On allows the projector to turn on automatically once the power is fed through the power cord.
Function Description 4. BASIC menu Audio Settings See "Adjusting the sound" on page 43 for details. Presentation Timer See "Setting the presentation timer" on page 32 for details. Pattern The projector can display several test patterns. It helps you adjust the image size and focus and check that the projected image is free from distortion. Blank Timer See "Hiding the image" on page 34 for details.
Function Description Closed Caption Enable Activates the function by selecting On when the selected input signal carries closed captions. • 5. ADVANCED menu Closed Caption Captions: An on-screen display of the dialogue, narration, and sound effects of TV programs and videos that are closed captioned (usually marked as "CC" in TV listings). This function is only available when a Composite video input signal is selected and its system format is NTSC.
Function Description Source Shows the current signal source. Color Mode Shows the selected mode in the IMAGE menu. Resolution Shows the native resolution of the input signal. 7. INFORMATION menu Color System Shows input system format. IP Address (PS600W/PS600X) Shows the IP address of your projector. MAC Address (PS600W/PS600X) Shows the MAC Address of your projector. MAC Address stands for Media Access Control Address, which is a physical layer address used to uniquely identify a network node.
Maintenance Care of the projector You need to keep the lens and/or filter (optional accessory) clean on a regular basis. Never remove any parts of the projector. Contact your dealer when any part of the projector needs replacing. Cleaning the lens Clean the lens whenever you notice dirt or dust on the surface. • • Use a canister of compressed air to remove dust. If there is dirt or smears, use lens-cleaning paper or moisten a soft cloth with lens cleaner and gently wipe the lens surface.
• If your projector is ceiling-mounted or is not easily accessible, pay special attention to your personal safety when replacing the dust filter. Installing the dust filter 1. 2. 3. Be sure to turn off the projector and unplug it from power source. As the arrows shown to the right, fit the filter by aligning and inserting it into the projector slots. Tighten the screw the secures the dust filter. 2 1 3 For first time installation: 4. Open the OSD menu and go to the ADVANCED > Filter Settings menu. 5.
CAUTION Remember to set Filter Mode to Off in the ADVANCED > Filter Settings menu when using the projector with the dust filter removed. Setting Filter Mode to Off does not reset the filter timer. The timer will continue counting the next time you fit the filter back on and set Filter Mode to On. Lamp information Getting to know the lamp hour When the projector is in operation, the duration (in hours) of lamp usage is automatically calculated by the built-in timer. To obtain the lamp hour information: 1.
Setting Sleep Timer This function allows the projector to turn off automatically after a set period of time to prevent unnecessary waste of lamp life. 1. Open the OSD menu and go to the POWER MANAGEMENT > Smart Energy menu. 2. Press Enter and the Smart Energy page is displayed. 3. Highlight Sleep Timer and press / . 4. If the preset time lengths are not suitable for your presentation, select Disable. The projector will not automatically shut down in a certain time period.
Indicators Light Status & Description Power events Blue Flashing Off Off Stand-by mode Blue Off Off Blue Off Off Powering up Normal operation Blue Flashing Off Off Normal power-down cooling (3 sec) Downloading Burn in off Red Off Off Blue Blue Blue Lamp events Blue Flashing Off Red First Lamp-Lit error cooling (60 sec) Off Off Red Blue Off Red Lamp error in normal operation (30 sec) CW start fail (30 sec) Thermal events Off Red Off Off Red Red Off Red Blue Off Red
Troubleshooting The projector does not turn on. Cause Remedy There is no power from the power cord. Plug the power cord into the AC inlet on the projector, and plug the power cord into the power outlet. If the power outlet has a switch, make sure that it is switched on. Attempting to turn the projector on again during the cooling process. Wait until the cooling down process has completed. No picture Cause Remedy The video source is not turned on or connected correctly.
Specifications Dimensions 293 mm (W) x 115 mm (H) x 220 mm (D) (Excluding extrusions) 293 220 115 61 90 Unit: mm Ceiling mount installation 199 61 Ceiling mount screws: M4 x 8 (Max.
IR control table Key Format Byte1 Byte2 Byte3 Byte4 PgDn (Page Down) NEC X3 F4 05 FA PgUp (Page Up) NEC X3 F4 06 F9 Blank NEC X3 F4 07 F8 Auto Sync NEC X3 F4 08 F7 Up NEC X3 F4 0B F4 Down NEC X3 F4 0C F3 Left NEC X3 F4 0E F1 Right NEC X3 F4 0F F0 Color Mode NEC X3 F4 10 EF Enter NEC X3 F4 15 EA Exit NEC X3 F4 28 D7 Eco Mode NEC X3 F4 2B D4 Menu NEC X3 F4 30 CF Source NEC X3 F4 40 BF Pattern NEC X3 F4 55 AA HDMI/H
Address code Code 1 83F4 Code 2 93F4 Code 3 A3F4 Code 4 B3F4 Code 5 C3F4 Code 6 D3F4 Code 7 E3F4 Code 8 F3F4 RS232 command table Pin Description Pin 1 NC 2 Description RX 3 TX 4 NC 5 GND 6 NC 7 RTSZ 8 CTSZ 9 NC RS-232 protocol Baud Rate 115200 bps (default) Data Length 8 bit Parity Check None Stop Bit 1 bit Flow Control None 63
Function Status Action cmd Turn on 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x00 0x00 0x5D Turn off 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x01 0x00 0x5E Write Power Read Power status (on/off) 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x00 0x5E Reset all settings Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x02 0x00 0x5F Reset Color Settings Execute 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x2A 0x00 0x87 Write Splash Screen Read Splash Screen Blue 0x06 0x14 0x00 0x04 0x00 0x34 0x
Front Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x00 0x5E Rear Table 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x01 0x5F Rear Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x02 0x60 Front Ceiling 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x00 0x03 0x61 Write Projector Position Read projector position status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x00 0x5F OFF 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x00 0x7E Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x20 0x01 0x7F Frame Sequential 0x06 0x1
Write Aspect ratio Read Auto Adjust Aspect ratio Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x00 0x62 Aspect ratio 4:3 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x02 0x64 Aspect ratio 16:9 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x03 0x65 Aspect ratio 16:10 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x04 0x66 Aspect ratio Anamorphic 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x04 0x05 0x67 Aspect ratio 2.
Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x00 0x68 Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0A 0x01 0x69 Keystone status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x0A 0x69 Decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x00 0x8E Increase 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x31 0x01 0x8F Keystone status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x31 0x8F Brightest 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x00 0x69 Movie 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x0B 0x01 0x6A Ph
Gain decrease 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x00 0x71 Gain increase 0x06 0x14 0x00 0x04 0x00 0x34 0x12 0x13 0x01 0x72 Write Gain Read Gain 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x12 0x13 0x72 Freeze on 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x01 0x60 Freeze off 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x00 0x00 0x5F Write Freeze Read Source input Write Read Freeze status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x13 0x00 0x60 Input source VGA 0x06 0x14 0x00 0x04 0x00 0x34 0x13 0x01 0
0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x00 0x61 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x01 0x62 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x02 0x63 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x03 0x64 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x04 0x65 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x05 0x66 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x06 0x67 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x07 0x68 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x08 0x69 0x06 0x14 0x00 0x04 0x00 0x34 0x15 0x00 0x09 0x6A 0x06 0x14 0x
Write HDMI Format Read Write HDMI Range Read RGB 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x00 0x85 YUV 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x01 0x86 Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x28 0x02 0x87 HDMI Format status 0x07 0x14 0x00 0x05 0x00 0x34 0x00 0x00 0x11 0x28 0x86 Enhanced 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x00 0x86 Normal 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x01 0x87 Auto 0x06 0x14 0x00 0x04 0x00 0x34 0x11 0x29 0x02 0x88 HDMI Range status 0x07 0x14 0x00 0x05 0x00
code 1 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x00 0xA0 code 2 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x01 0xA1 code 3 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x02 0xA2 code 4 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x03 0xA3 code 5 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x04 0xA4 code 6 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x05 0xA5 code 7 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x06 0xA6 code 8 0x06 0x14 0x00 0x04 0x00 0x34 0x0C 0x48 0x07 0xA7 Remote Control code status 0x07 0x14 0x
Remote Key Write Menu 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0F 0x61 Exit 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x13 0x65 Up 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0B 0x5D Down 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0C 0x5E Left 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0D 0x5F Right 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x0E 0x60 Source 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x04 0x56 Enter 0x02 0x14 0x00 0x04 0x00 0x34 0x02 0x04 0x15 0x67 Auto 0x02 0x14 0x00 0x04 0x00 0x34
Timing chart Analog RGB Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) VGA 640 x 480 4:3 60/72/75/85 SVGA 800 x 600 4:3 60/72/75/85 1024 x 768 4:3 60/70/75/85 1152 x 864 4:3 75 1280 x 768 15:9 60 1280 x 800 16:10 60/75/85 1360 x 768 16:9 60 Quad-VGA 1280 x 960 4:3 60/85 SXGA 1280 x 1024 5:4 60 WXGA 1366 x 768 16:9 59.
HDMI Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) VGA 640 x 480 4:3 60 SVGA 800 x 600 4:3 60 XGA 1024 x 768 4:3 60 1280 x 768 15:9 60 1280 x 800 16:10 60 1360 x 768 16:9 60 Quad-VGA 1280 x 960 4:3 60 SXGA 1280 x 1024 5:4 60 WXGA 1366 x 768 16:9 59.
3D (HDMI signal included) Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) SVGA 800 x 600 4:3 60* / 120** XGA 1024 x 768 4:3 60* / 120** HD 1280 x 720 16:9 50* / 60* / 120** WXGA 1280 x 800 16:9 60* / 120** Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) SDTV (480i)*** 720 x 480 4:3 / 16:9 60 for Video Signal * 50Hz and 60Hz signals are supported for Side-by-Side, Top-Bottom, and Frame Sequential formats.
Component video Signal Resolution (dots) Aspect Ratio Refresh Rate (Hz) HDTV (1080p) 1920 x 1080 16:9 50 / 60 HDTV (1080i) 1920 x 1080 16:9 50 / 60 HDTV (720p) 1280 x 720 16:9 50 / 60 SDTV (480p) 720 x 480 4:3 / 16:9 60 SDTV (576p) 720 x 576 4:3 / 16:9 50 SDTV (480i) 720 x 480 4:3 / 16:9 60 SDTV (576i) 720 x 576 4:3 / 16:9 50 Composite video Signal Aspect Ratio Refresh Rate (Hz) NTSC 4:3 60 PAL 4:3 50 PAL60 4:3 60 SECAM 4:3 50 76
Projector specifications All specifications are subject to change without notice. Not all models can be purchased in your region. Model name PS600X PS600W PS501W PS501X PS500X Product Specification Resolution Throw ratio Display system Lamp Type 0.55” XGA (1024 x 768) 0.61 190 W (RLC108) 0.65” WXGA (1280 x 800) 0.49 1-CHIP DMD 0.55” XGA (1024 x 768) 0.61 200 W (RLC-109) 190 W (RLC-108) Input connector RGB-in Component input S-Video Composite input Audio-in RCA R&L Mini USB HDMI (1.
Operating Altitude 0–1499 m at 5°C–35°C 1500–3000 m at 5°C–25°C (with High Altitude Mode on) Operating Relative Humidity 10%–90% (without condensation) 78
Copyright information Copyright Copyright © 2017. All rights reserved. No part of this publication may be reproduced, transmitted, transcribed, stored in a retrieval system or translated into any language or computer language, in any form or by any means, electronic, mechanical, magnetic, optical, chemical, manual or otherwise, without the prior written permission of ViewSonic Corporation.
Customer Support For technical support or product service, see the table below or contact your reseller. Note : You will need the product serial number. Website T= Telephone C = CHAT ONLINE Email Australia/New Zealand www.viewsonic.com.au AUS= 1800-880-818 NZ= 0800-008-822" service@au.viewsonic.com Canada www.viewsonic.com T= 1-866-463-4775 service.ca@viewsonic.com Europe www.viewsoniceurope.com www.viewsoniceurope.com/eu/support/call-desk/ Hong Kong www.hk.viewsonic.
Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components.
How to get service: 1. For information about receiving service under warranty, contact ViewSonic Customer Support (please refer to “Customer Support” page). You will need to provide your product’s serial number. 2. To obtain warranted service, you will be required to provide (a) the original dated sales slip, (b) your name, (c) your address, (d) a description of the problem, and (e) the serial number of the product. 3.
Mexico Limited Warranty ViewSonic® Projector What the warranty covers: ViewSonic warrants its products to be free from defects in material and workmanship, under normal use, during the warranty period. If a product proves to be defective in material or workmanship during the warranty period, ViewSonic will, at its sole option, repair or replace the product with a like product. Replacement product or parts may include remanufactured or refurbished parts or components & accessories.
Contact Information for Sales & Authorized Service (Centro Autorizado de Servicio) within Mexico: Name, address, of manufacturer and importers: México, Av. de la Palma #8 Piso 2 Despacho 203, Corporativo Interpalmas, Col. San Fernando Huixquilucan, Estado de México Tel: (55) 3605-1099 http://www.viewsonic.com/la/soporte/index.htm NÚMERO GRATIS DE ASISTENCIA TÉCNICA PARA TODO MÉXICO: 001.866.823.2004 Hermosillo: Distribuciones y Servicios Computacionales SA de CV. Calle Juarez 284 local 2 Col. Bugambilias C.
