TD1655 顯示器 使用指南 型號 VS18170 P/N:TD1655
感謝您選擇 ViewSonic® 作為領先全球的視覺解決方案供應商,ViewSonic® 致力於超越全球對技術 進化、創新和簡單性的期望。在 ViewSonic®,相信我們的產品有可能對世界 造成正面影響,而我們有信心,您將對您選擇的 ViewSonic® 產品感到滿意。 再次感謝您選擇 ViewSonic®! 2
安全注意事項 開始使用裝置前,請先閱讀以下安全注意事項。 • 請將本使用指南放在安全的地方,以便日後參考。 • 請閱讀所有警告並遵守所有指示。 • 請坐在離裝置至少 18" (45 cm) 處。 • 請在裝置周圍保留至少 4" (10 cm) 的空隙,以確保良好通風。 • 請將裝置放在通風良好的區域。請勿將任何會阻礙散熱的物品放在裝置 上。 • 請勿在靠近水的地方使用裝置。為降低火災或觸電的風險,請勿讓裝置 受潮。 • 請避免讓裝置受陽光直射或暴露在其他持續熱源下。 • 請勿安裝於接近熱源的地方,例如散熱器、暖氣機、火爐或其他可能使 裝置溫度升高至危險水準的裝置(包括擴大機)。 • 請使用柔軟的乾布清潔外殼。如需更多資訊,請參閱第 35 頁「維護」 一節。 • 觸摸螢幕時,油可能會聚集在螢幕上。若要清潔螢幕上的油漬,請參閱 第 35 頁「維護」一節。 • 請勿用尖銳或堅硬的物體觸碰螢幕表面,否則可能會損壞螢幕。 • 移動裝置時,小心別讓裝置掉落或撞到任何東西。 • 請勿將裝置放在不平穩的平面上。裝置可能會傾倒,導致人員受傷或裝置 故障。 • 請勿在裝置或連接線上放置任何重物。 • 如果冒煙、出現異音或異味,請
• 連接至電源插座時,請勿拆除接地插腳。請確保接地插腳不被拆除。 • 請避免讓電源線受到踩踏或擠壓,尤其是插頭以及電源線與設備的 連接處。請確保電源插座位於設備附近,以便使用。 • 僅限使用製造商規定的附件/配件。 • 若使用推車,移動推車/設備組合時請務必小心,以免翻覆導致 人員受傷。 • 如果長時間不使用裝置,請將電源插頭從 AC 插座上拔下。 • 維修作業應交由合格的專業人員執行。裝置有任何損壞時,將需要維修, 例如: ͫ 電源線或插頭損壞 ͫ 液體濺到裝置上或物體掉入裝置中 ͫ 裝置受潮 ͫ 裝置無法正常運作或摔落 • 使用過度恐傷害視力。注意事項內容: ͫ (1)使用30分鐘請休息10分鐘。 ͫ (2) 未滿2歲幼兒不看螢幕,2歲以上每天看螢幕不要超過 1 小時。 • 注意:長時間在高音量下使用入耳式耳機/頭戴式耳機,可能導致聽力 受損/聽力損失。使用入耳式耳機/頭戴式耳機時,請將音量調整至適當 水準,否則可能導致聽力受損。 • 注意:顯示器可能會過熱並關閉!如果裝置自動關閉,請再次開啟顯示 器。重新啟動後,請變更顯示器的解析度和更新率。如需詳細資訊,請參 閱 顯示卡的使用指南。 4
目錄 安全注意事項 ............................................................. 3 介紹 ............................................................................ 7 包裝內容物 ............................................................................................................7 產品概述 ................................................................................................................8 正視圖和左側視圖 ................................................................................................. 8 後視圖和右側視圖 ..
附錄 .......................................................................... 27 規格 ......................................................................................................................27 字彙 ......................................................................................................................29 疑難排解 ..............................................................................................................33 維護 ..............................................................
介紹 包裝內容物 • • • • • • • • • 可攜式觸控顯示器 變壓器 USB Type C 線 USB Type C 至 Type A 線 Mini-HDMI 至 HDMI 線 護套 清潔布 被動式觸控筆 快速啟用指南 備註: 包裝中隨附的電源變壓器和視訊線可能因國家而異。如需更多 資訊,請聯絡當地經銷商。 7
產品概述 正視圖和左側視圖 Type C Type C HDMI 後視圖和右側視圖 支架 電源 LED Joy Key (搖桿鍵) I/O 連接埠 Type C Type C HDMI 1 1 USB Type C 2 Mini HDMI 2 3 3 音訊輸出 備註: 欲深入瞭解 Middle(中) (l)//// 按鍵及其功能,請參閱 第 18 頁的「快速鍵」。 8
初始設置 安裝護套 使用護套和支架 備註: 請務必將裝置放在平穩的表面上。否則可能導致裝置掉落、並損壞 裝置及/或導致人員受傷。 9
建立連接 連接至電源 可用以下任一配置為顯示器供電: • Type C 連接 (功率輸出必須大於 10W) • Type A 連接 (功率輸出必須大於 10W) • 電源變壓器 100-240 Vac 50/60 Hz 備註: 如需更多資訊,請參閱第 13 頁的「供電」。 10
連接外部裝置和觸控連接 您的外部裝置可透過任一下列配置連接: • Type C 連接 將 Type C 線從外部裝置,連接到螢幕的 Type C 連接埠。 或 (功率輸出必須大於 10W) • Mini HDMI 連接 1. 將迷你 HDMI 線從外部裝置連接到顯示器的迷你 HDMI 連接埠。 2.
觸控功能控制 使用觸控功能時,請注意: • 若拔下 USB 線,然後再插入,或電腦從睡眠模式恢復,觸控功能約 需 5 秒鐘的時間才會恢復。 • 觸控螢幕最多僅可偵測到 10 隻手指。 • 若 Windows 游標未在您觸摸螢幕時準確追隨您的手指移動,請進行 以下行動: 1. 開啟: Control Panel(控制台) > Hardware and Sound(硬體和 音效) > Tablet PC Settings(平板電腦設定) 2. 選擇 Calibration(校正)。 3.
供電 為筆記型電腦或手機供電 如果將隨附的電源變壓器連接至顯示器,則顯示器可以為連接的筆記型電腦或 手機充電。 備註: 供電輸出:DC 5V/9V/12V/15V/20V/ 最大 3A。 100-240 Vac 50/60 Hz 電源偵測 本產品將偵測電源裝置是變壓器、筆記型電腦或手機。 • 如果電源是變壓器或筆記型電腦,則預設亮度值為 100。 • 如果電源是手機,則預設亮度值為 15。 • 使用手機為顯示器供電時,預設亮度為 15。 備註: 由於手機的功率輸出有限,請勿調高亮度,否則可能導致顯示器 閃爍或關閉。 13
供電 - 其他資訊 由於 TD1655 的設計,請注意: • 第一個連接的裝置將是主要輸入訊號。 • Type C 連接埠將外部裝置辨識為電源變壓器時,只會分配電力。不會顯示 輸入訊號。 • 只有在其中一個 Type C 連接埠被辨識為電源變壓器時,另一個連接埠才能 提供雙向電力。 如果先將筆記型電腦連接至 TD1655 Type C port,TD1655 另一個Type C port 再 連接手機,則不會為手機的電池充電,因為兩個 Type C 連接埠都不會將連線 辨識為連接至電源變壓器。 備註: 若要顯示手機畫面,必須拔下連接至筆記型電腦的 Type C 線。 如果先將手機連接至 TD1655 Type C port,TD1655 另一個 Type C port 再連接筆 記型電腦,則會為手機的電池充電,因為其中一個 Type C 連接埠被辨識為連 接至電源變壓器。 備註: 若要顯示筆記型電腦畫面,必須拔下連接至手機的 Type C 線。 因 TD1655設計的緣故,請勿同時接兩台筆記型電腦或一台筆記型電腦與桌上 型電腦。這會導致電源分配衝突,因而造成螢幕閃爍或筆記型電腦強制關機。 備註: • 若筆記
使用顯示器 調整視角 傾斜角度調整 透過隨附的支架將顯示器向後傾斜至所需視角(20˚ 至 60˚)。 eC Typ eC Typ I HDM 備註: 調整時,請用一隻手牢牢支撐顯示器,同時用另一隻手向後傾斜 底座。 15
開啟/關閉裝置 1. 以任一可用配置連接至電源。如需更多資訊,請參閱第 10 頁。 2. 按 Middle(中)(l) 按鈕開啟顯示器。 3.
快速選單 按 /// 鍵啟動快速選單。 ViewMode Contrast/Brightness Input Select Main Menu Exit 備註: 依照畫面上顯示的按鍵指南選擇選項或進行調整。 功能表 ViewMode (影像調校) 說明 選擇預設色彩設定。 Contrast/Brightness 調整對比或亮度。 (對比/亮度) Input Select (輸入選取) 選擇輸入來源。 Main Menu (主功能表) 進入螢幕顯示 (OSD) 選單。 Exit(退出) 退出快速選單。 17
快速鍵 螢幕顯示 (OSD) 選單關閉時,您可以使用控制面板按鍵快速存取特殊功能。 按鍵 t 說明 按住此鍵可鎖定/解鎖 OSD 選單。 畫面上出現選單時,繼續按住該鍵 5 秒可鎖定/解鎖 OSD 選單。 OSD Lock/Unlock Locking OSD 1 Press and hold for 10s to lock OSD 如果 OSD 選單鎖定,畫面上會出現以下訊息: OSD Lock/Unlock OSD Locked 18
按鍵 u 說明 按住此鍵可鎖定/解鎖 Power(電源)按鈕。 畫面上出現選單時,繼續按住該鍵 5 秒可鎖定/解鎖 Power (電源)按鈕。 Power Lock/Unlock Locking Power Button 3 Press and hold for 10s to lock power 如果 Power(電源)按鈕鎖定,畫面上會出現以下訊息: Power Lock/Unlock Power Button Locked p 按住此鍵 5 秒鐘,可顯示/隱藏裝置開啟時的啟動畫面。 Boot Up Screen On/Off Off Press to turn on 19
按鍵 q 說明 按住此鍵 5 秒鐘以開啟 DDC/CI 和 DDC/2B。 DDCCI/DDC2B Off Press to turn on 20
配置設定 一般操作 1. 按 Middle(中)(l) 鍵顯示螢幕顯示 (OSD) 選單。 Input Select Audio Adjust ViewMode Color Adjust Manual Image Adjust Setup Menu Type C HDMI 1920 x 1080 @ 60Hz 75% 2.
3. 按 或 鍵選擇所需的選單。然後按 Middle(中)(l) 鍵進入子功能表。 Input Select Audio Adjust ViewMode Color Adjust Contrast/Brightness sRGB Color Temperature Bluish Color Space Cool Color Range Native Manual Image Adjust Setup Menu Warm User Color 1920 x 1080 @ 60Hz 75% 4.
螢幕顯示 (OSD) 選單樹狀結構 主功能表 子功能表 選單選項 Input Select Type C (輸入選取) HDMI Audio Adjust Volume(音量) (自動調整) Mute(靜音) Off(關閉) ViewMode (影像調校) Office (-/+, 0~100) On(開啟) Off(關閉) Web(網路) Text(文字) Movie(電影) MAC Mono(單色模式) FPS 1 Game(遊戲) FPS 2 RTS MOBA Color Adjust Contrast(對比)/ Contrast(對比) (色彩調整) Brightness(亮度) Brightness(亮度) Color Temperature (色溫) (-/+, 0~100) (-/+, 0~100) sRGB Bluish(偏藍色) Cool(冷色調) Native(原生) Warm(暖色調) Red(紅色) (-/+, 0~100) User Color (使用者色彩) Green (綠色) (-/+, 0~100) Blue(藍色) (-/+, 0~100) Col
主功能表 子功能表 選單選項 Manual Image Adjust (手動影像 調整) Sharpness (銳利度) (-/+, 0/25/50/75/100) Dynamic Contrast (動態對比度) (-/+, 0/25/50/75/100) Response Time (反應時間) Standard(標準) Advanced(進階) Ultra Fast(超速) Aspect Ratio (縱橫比) 4:3 Overscan (全畫面) On(開啟) Low Input Lag (低輸入延遲) On(開啟) Blue Light Filter (濾藍光) (-/+, 0~100) Full Screen(全螢幕) Off(關閉) Off(關閉) 24
主功能表 子功能表 選單選項 Setup Menu Language Select (設定選單) (語言選擇) English Français Deutsch Español Italiano Suomi Svenska Русский Türkçe Česká 日本語 한국어 繁體中文 简体中文 Resolution Notice (解析度提示) On(開啟) Off(關閉) Information(資訊) OSD Time Out (OSD逾時) (-/+, 5/15/30/60) OSD Background (選單背景) On(開啟) OSD Pivot (選單旋轉) 0° Power Indicator (電源指示燈) On(開啟) Boot Up Screen (開機畫面) On(開啟) Auto Power Off (自動關機) On(開啟) Off(關閉) 90° Off(關閉) Off(關閉) Off(關閉) 25
主功能表 子功能表 Setup Menu Sleep(睡眠) (設定選單) 選單選項 30 Minutes (30 分鐘) 45 Minutes (45 分鐘) 60 Minutes (60 分鐘) 120 Minutes (120 分鐘) Off(關閉) ECO Mode (ECO 模式) DDC/CI Auto Detect (自動偵測) Standard(標準) Optimize(低節能) Conserve(高節能) On(開啟) Off(關閉) On(開啟) Off(關閉) Memory Recall(記憶還原) 26
附錄 規格 項目 類別 規格 LCD 類型 TFT,主動式矩陣 1920 x 1080 LCD; 0.1792 (H)mm x 0.1792 (V)mm 像素間距 39.6 cm,16”(15.6” 可視範圍) RGB 垂直條紋 抗指紋,6H 硬塗層 TMDS 數位 (100 Ω) HDMI (v. 1.
項目 儲存條件 尺寸 重量 省電模式 類別 規格 溫度 濕度 海拔 實體 (寬 x 高 x 深) 實體 開啟3 關閉 -20° C 至 60° C(-4° F 至 140° F) 5% 至 90%(無冷凝) 40,000 英尺 (12.1 km) 355.5 x 223.4 x 14.7 mm (14.5” x 8.79” x 0.58”) 0.94 kg (2.07 lbs) 7W(標準值) < 0.
字彙 本節說明 LCD 顯示器機型使用的標準術語。依字母順序列出所有術語。 備註: 某些術語可能不適用於您的顯示器。 A Advanced DCR(進階 DCR) 先進的 DCR 技術會自動偵測影像訊號,並以智慧型的方式控制背光 亮度與色彩,藉以改進功能,使黑暗場景中的黑色更深邃,並使明亮 環境中的白色更明亮。 Audio Adjust(自動調整) 調整音量、將聲音靜音,或是在您有一個以上來源時,於輸入間進行 切換。 Auto Detect(自動偵測) 如果目前的輸入來源沒有訊號,顯示器會自動切換至下一個輸入選項。 此功能在部分機型上預設為停用。 Auto Image Adjust(自動影像調整) 自動調整大小、置中以及微調視訊訊號,消除波紋與失真。 B Blue Light Filter(濾藍光) 調整可阻隔高能藍光的濾光片,帶來更舒適的觀看體驗。 Brightness(亮度) 調整螢幕影像的背景黑階。 29
C Color Adjust(色彩調整) 提供數種色彩調整模式,有助調整色彩設定,以符合使用者的需求。 Color Space(色彩空間) 允許使用者選擇要使用哪種色彩空間,作為顯示器色彩輸出 (RGB, YUV)。 Color Temperature(色溫) 允許使用者選取特定的色溫設定,進一步自訂專屬的觀看體驗。 面板預設 面板原始狀態 sRGB 用於 Windows 系統的標準色彩空間。 Bluish (偏藍色) 將色溫設為 9,300K。 Cool (冷色調) 將色溫設為 7,500K。 Native (原生) 預設色溫。建議用於一般用途。 Warm (暖色調) 將色溫設為 5,000K。 Contrast(對比) 調整影像背景(黑階)與前景(白階)之間的差異。 I Information(資訊) 顯示來自電腦顯示卡的時序模式(視訊訊號輸入)、LCD 型號、序號, 以及 ViewSonic® 網站網址。請參閱顯示卡的使用指南,瞭解如何變更 解析度及更新率(垂直頻率)。 備註: 例如,VESA 1024 x 768 @ 60Hz 表示解析度為 1024 x 768, 更新率
M Manual Image Adjust(手動影像調整) 顯示「Manual Image Adjust」(手動影像調整)選單。您可以手動設定 各種影像品質調整。 Memory Recall(記憶還原) 顯示器以本手冊「規格」中列出的出廠預設時序模式運作時,恢復 調整前的出廠設定。 備註: • (例外)此控制不影響在「Language Select」(語言選擇)或 「Power Lock」(電源鎖定)設定中所做的變更。 • 記憶還原是預設的出貨顯示器配置與設定。記憶還原是產品 符合 ENERGY STAR® 資格的設定。若對預設出貨顯示器配置與 設定做任何改變,都會變更耗電量,且可能會使耗電量超過 ENERGY STAR® 資格所需的限制(若適用)。 ENERGY STAR® 是美國環境保護局 (EPA) 核發的省電 指導方針。ENERGY STAR® 是美國環保署與美國 能源部門的合作計畫,有住於透過節能產品與 實務節省金錢並保護環境。 O Overscan(全畫面) 請參考顯示器螢幕上的裁切影像。顯示器的設定會放大電影內容, 讓您看不到電影的最外緣。 31
R Recall(回復模式設定) 重設 ViewMode 顯示器設定。 Resolution Notice(解析度提示) 提示會通知使用者,目前的觀看解析度不是正確的原生解析度。設定 顯示器解析度時,顯示器設定視窗中會出現此提示。 Response Time(反應時間) 調整反應時間,創造沒有條紋、模糊或殘影的流暢影像。低反應時間 非常適合大多數圖形密集的遊戲,並能在觀賞運動賽事或動作片時, 提供令人驚艷的視覺品質。 S Setup Menu(設定選單) 調整螢幕顯示 (OSD) 選單設定。多數這些設定都能啟動畫面顯示通知, 讓使用者不必重新開啟選單。 Sharpness(銳利度) 調整顯示器的畫質。 V ViewMode(影像調校) ViewSonic 獨特的 ViewMode(影像調校)功能提供「Game」(遊戲)、 「Movie」(影片)、「Web」(網頁瀏覽)、「Text」(文字)、 「MAC」與「Mono」(單色模式)預設。這些預設經過特別設計, 可為各種螢幕應用提供最佳的觀看體驗。 32
疑難排解 本節說明使用顯示器時,可能會遇到的常見問題。 問題 可能解決方法 無電源 • 確定已按 Power(電源)按鈕開啟顯示器。 • 確定電源線已正確、穩固地連接至顯示器和電 源插座。 • 將另一個電氣裝置插入電源插座,以確認插座 是否供電。 電源開啟,但螢幕上 未出現影像 • 確定將顯示器連接至電腦的視訊線,已正確、 穩固地連接。 • 調整亮度和對比設定。 • 確定已選擇正確的輸入來源。 色彩錯誤或異常 • 如果缺少任何色彩(紅色、綠色或藍色), 請檢查視訊線是否已正確、穩固地連接。連接 線接頭的接腳鬆脫或斷裂,可能導致不當連 接。 • 將顯示器連接至另一部電腦。 • 如果您的顯示卡較舊,請聯絡 ViewSonic® 取得 非 DDC 轉接器。 螢幕影像太亮或太暗 • 透過 OSD 選單調整亮度和對比設定。 • 將顯示器重設為出廠設定。 螢幕影像切入和切出 • 確定已選擇正確的輸入來源。 • 檢查視訊線接頭是否有彎曲或斷裂的接腳。 • 確定將顯示器連接至電腦的視訊線,已正確、 穩固地連接。 螢幕影像模糊 • 將解析度調整成正確的長寬比。 • 將顯示器重設為出廠設定。 33
問題 可能解決方法 畫面未正確置中 • 透過 OSD 選單調整水平和垂直控制。 • 檢查長寬比。 • 將顯示器重設為出廠設定。 畫面偏黃色 • 確定「Blue Light Filter」(濾藍光)已關閉。 螢幕尚未出現 OSD 選單/無法存取 OSD 控制 • 檢查 OSD 選單是否鎖定。如果是,則按住 3 和 5 鍵 10 秒。 • 關閉顯示器,拔下電源線再插回,然後開啟 顯示器。 • 將顯示器重設為出廠設定。 控制面板按鍵無效 • 一次只按一顆按鍵。 • 重新啟動電腦。 OSD 中有某些選單 無法選擇 • 調整 ViewMode 或輸入來源。 • 將顯示器重設為出廠設定。 無音訊輸出 • 如果使用入耳式耳機/頭戴式耳機,請連接迷 你立體聲插孔。 • 確定音量未靜音也未設為 0。 • 檢查 Audio Input(音訊輸入)設定。 顯示器無法調整 • 確保顯示器附近沒有障礙物且有足夠的間距。 • 如需更多資訊,請參閱第15頁「調整視角」。 連接至顯示器的 USB 裝置無法運作 • 確定 USB 線已正確連接。 • 嘗試換成其他 USB 連接埠(如適用)。 • 某些 USB
維護 一般注意事項 • 確定顯示器已關閉且電源線已從電源插座上拔下。 • 切勿將任何液體直接噴灑、或倒在螢幕或外殼上。 • 小心操作顯示器,因為深色顯示器如果磨損,痕跡可能會比淺色顯示器 更明顯。 清潔螢幕 • 用乾淨、柔軟的無棉絮布擦拭螢幕。如此可去除灰塵及其他微粒。 • 如果螢幕還是不乾淨,請用乾淨、柔軟的無棉絮布沾取少量不含氨、 不含酒精的玻璃清潔劑;然後擦拭螢幕。 清潔外殼 • 使用軟的乾布。 • 如果外殼還是不乾淨,請用乾淨、柔軟的無棉絮布沾取少量不含氨、 不含酒精的中性非研磨清潔劑,然後擦拭表面。 免責聲明 • ViewSonic® 不建議在顯示器螢幕或外殼上,使用任何含氨或酒精的清潔 劑。 已知某些化學清潔劑會損壞顯示器的螢幕及/或外殼。 • ViewSonic® 對使用任何含氨或酒精的清潔劑所造成的損壞,概不負責。 35
法規和服務資訊 法規符合性資訊 本節說明關於法規的所有相關要求和聲明。確認的對應應用應參考裝置上的 銘牌標籤和相關標記。 FCC 符合性聲明 本設備符合 FCC 規則第 15 部分的規定。操作時有以下兩種情況:(1) 本裝置 不會造成有害的干擾,以及 (2) 本裝置必須接受任何接收到的干擾,包括造成 操作不良的干擾。本設備已通過測試並符合 FCC 規則第 15 部分有關 B 級數位 裝置的規定。 這些限制旨在提供合理的保護,以防在一般住宅環境中造成有害干擾。本設備 會產生、使用和發射無線電頻率能量,因此若沒有依照指示安裝及使用,可能 會對無線電通訊產生有害的干擾。然而,並不保證在特定安裝方式下不會產生 干擾。在住宅區中運作本設備亦可能造成有害干擾,在這種情況下,使用者 會被要求採用以下一種或多種方法改善干擾的情形。 • • • • 重新調整或放置接收天線。 增加設備與無線接收設備的距離。 將本設備連接到與接收器不同的電源插座上。 請向經銷商或具有經驗的無線電/ 電視技術人員請求幫助。 警告:進行任何本手冊未明確核准的變更或修改可能使您沒有權利操作 本產品。 加拿大工業部聲明 CAN ICES-3 (
以下資訊僅適用於歐盟成員國: 右側所示的符號符合《廢電子電機設備指令 2012/19/EU (WEEE)》之 規定。此符號表示不得將設備視為未分類都市廢棄物棄置,而是必須 依照當地法律使用回收和收集系統。 台灣 RoHS 符合性聲明 依檢驗標準 CNS15663 之規定將限用物質含有情況標示於表列商品之本體、包 裝、標貼、或說明書。以下表格列出了產品中可能包含的有害物質的名稱和含 量。 限用物質及其化學符號 單元 鉛 (Pb) 汞 (Hg) 鎘 (Cd) 六價鉻 多溴聯苯 (Cr+6) (PBB) 多溴二苯醚 (PBDE) 支架/外殼 ○ ○ ○ ○ ○ ○ 印刷電路板 (PCBA)* – ○ ○ ○ ○ ○ 玻璃面板 – ○ ○ ○ ○ ○ 電纜/電線/連接器 – ○ ○ ○ ○ ○ 電源設備/外接電源 供應器 – ○ ○ ○ ○ ○ 備考1.〝超出0.1 wt%〞及〝超出0.01 wt%〞係指限用物質之百分比含量超出 百分比含量基準值。 備考2.〝○〞係指該項限用物質之百分比含量未超出百分比含量基準值。 備考3.
產品壽命結束時的產品棄置 ViewSonic® 尊重環境,致力於綠色工作和生活。感謝您參與 Smarter, Greener Computing。請造訪 ViewSonic® 網站深入瞭解。 美國和加拿大: http://www.viewsonic.com/company/green/recycle-program/ 歐洲: http://www.viewsoniceurope.com/eu/support/call-desk/ 台灣: https://recycle.epa.gov.
版權聲明 Copyright© ViewSonic® Corporation, 2020。保留所有權利。 Macintosh 和 Power Macintosh 是 Apple Inc.
客戶服務 關於技術支援或產品服務,請參照下表或洽詢經銷商。 備註: 需要產品序號。 國家/地區 網站 國家/地區 網站 亞太地區和非洲 Australia www.viewsonic.com/au/ Bangladesh www.viewsonic.com/bd/ 中国 (China) www.viewsonic.com.cn 香港 (繁體中文) www.viewsonic.com/hk/ Hong Kong (English) www.viewsonic.com/hk-en/ India www.viewsonic.com/in/ Indonesia www.viewsonic.com/id/ Israel www.viewsonic.com/il/ 日本 (Japan) www.viewsonic.com/jp/ Korea www.viewsonic.com/kr/ Malaysia www.viewsonic.com/my/ Middle East www.viewsonic.com/me/ Myanmar www.viewsonic.
有限保固 ViewSonic® 顯示器 保固範圍: ViewSonic® 保證其產品在保固期內,無材料和做工瑕疵。如果產品在保固期內 經證明有材料或做工瑕疵,ViewSonic® 將自行斟酌修復產品或以同型產品 替換,此為唯一補救辦法。替換產品或零件可能包含重新製造或整修的零件或 組件。維修或替換裝置或零件視客戶的原始有限保固剩下的時間而定,保固期 不延長。ViewSonic® 不對產品隨附或客戶安裝的任何第三方軟體、安裝任何 未經授權的硬體零件或元件(例如投影機燈泡)提供擔保。(請參閱:「不在 保固範圍內的事項」一節)。 有效保固期限: 視所在國家而定,ViewSonic® 顯示器保固期為 1 到 3 年,適用於包括光源在內 的所有零件、以及自第一消費者購買日起的所有人力。 保固範圍: 此保固僅對第一購買者有效。 不在保固範圍內的事項: • 任何序號被損毀、塗改或擦除的產品。 • 由於以下原因造成的產品損壞、損傷或故障: ͫ 意外事故、操作失當、疏忽、火災、水災、閃電或其他自然災害、未經 授權的產品修改或未遵循產品提供的說明而造成的損壞。 ͫ 被未經 ViewSonic® 授權的任何個人修復或嘗試修復過。
• • • • • • • 產品以外的原因,例如電源波動或故障。 使用不符合 ViewSonic 規格的供應品或零件。 擁有者未依照使用指南所述執行定期產品維護。 與產品缺陷無關的其他原因所致。 長時間顯示的靜態(非移動)影像造成的損壞(又稱為影像烙印)。 軟體-產品隨附或客戶安裝的任何第三方軟體。 硬體/配件/零件/元件-安裝任何未經授權的硬體、配件、消耗品或 元件(例如投影機燈泡)。 • 透過產品使用指南所述的不當清潔,損壞或濫用顯示器表面上的塗層。 • 拆卸、安裝和設定服務費用,包括產品的壁掛式安裝。 如何獲得服務: • 欲瞭解如何在保固期內獲得服務,請聯繫 ViewSonic® 客戶支援(請參閱 「客戶服務」頁)。您必須提供產品序號。 • 若要獲得保固服務,您必須提供:(a) 標有日期的原始購買單據、(b) 您的 姓名、(c) 您的住址、(d) 問題說明、(e) 產品序號。 • 以預付運費的方式,將產品裝在原包裝箱內送到或運至 ViewSonic® 授權 服務中心或 ViewSonic®。 • 如需其他資訊或離您最近的 ViewSonic® 服務中心名稱,請聯繫 ViewSonic® 。 損失免責條
ViewSonic 將不負責承擔: ViewSonic 的責任僅限於負擔產品的維修或更換成本。ViewSonic® 對以下情況 概不負責: • 由於本產品缺陷導致的任何財產損失、由於本產品使用不便導致的損失、 使用本產品導致的損失、時間損失、利潤損失、商業機會損失、商譽損 失、 業務關係損失、其他商業損失,即便已被提醒會造成這樣的損失也不負 責。 • 任何其他損失,不論是意外的、繼發性的或其他損失。 • 任何他方對客戶提出的索賠。 • 被未經 ViewSonic® 授權的任何個人修復或嘗試修復過。 美國州法的效力: 此保固為您提供特定的法律權利,您也有可能因為所在州的不同而享有其他 權利。某些州不允許隱含保固限制、及/或不允許意外或繼發性損失免責, 所以上述限制和免責條款可能不適用於您。 美國、加拿大以外地區之銷售: 如需在美國和加拿大以外地區銷售的 ViewSonic® 產品保固資訊和服務, 請聯繫 ViewSonic® 或當地 ViewSonic® 經銷商。 本產品在中國大陸(香港、澳門、台灣除外)的保固期,受維修保證卡的條款 與細則約束。 歐洲和俄羅斯使用者如需完整的保固資訊,請至: http://ww
Process Color C0 M91 Y72 K24 Process Color C0 M0 Y0 K100 Process Color C0 M91 Y72 K24 Spot Color Pantone Black C Spot Color Pantone 187 C