TD1711 터치 디스플레이 사용자 안내서 모델 번호 : VS17441 P/N: TD1711
준수 정보 참고: 이 섹션에서는 규정에 관한 선언 및 모든 관련된 요구사항을 설명합니다. 확인된 해당 애플리케이션은 장치에 있는 명판 레이블 및 관련 표시를 참조해야 합니다. FCC 적합성 선언 본 장치는 FCC 규정 제 15 부를 준수합니다. 작동에는 다음 두 가지 조건이 적용됩니다. (1) 본 장치는 유해 간섭을 일으키지 않으며, (2) 본 장치는 원치 않는 작동을 일으킬 수 있는 간섭을 포함하여 수신된 어떠한 간섭도 수용해야 합니다. 본 장치는 FCC 규정 제15부에 따라 테스트 되었으며 B급 디지털 장치에 대한 제한사항을 준수한다는 판정을 받았습니다. 이러한 제한사항은 주거 지역에 설치 시 유해 간섭에 대한 적절한 보호를 제공하기 위해 마련된 것입니다. 본 장치는 무선 주파수 에너지를 생성, 사용 및 방출할 수 있으며, 지침에 따라 설치하고 사용하지 않을 경우 무선 통신에 유해한 간섭을 일으킬 수 있습니다. 그러나 특정 설치 시 간섭이 발생하지 않을 것이라는 보장은 없습니다.
RoHS2 적합성 선언 본 제품은 전기 및 전자 기기 내 특정 유해물질의 사용에 대한 제한에 관한 유럽 의회와 이사회의 2011/65/EU 지침(RoHS2 지침)에 따라 설계 및 제조되었고, 아래와 같이 유럽 기술적합위원회(TAC)가 확정한 최대 농도 값을 준수합니다. 물질 제안된 최대 농도 실제 농도 납 (Pb) 0.1% < 0.1% 수은 (Hg) 0.1% < 0.1% 카드뮴 (Cd) 0.01% < 0.01% 6 가 크롬 (Cr6+) 0.1% < 0.1% 폴리브롬화비페닐 (PBB) 0.1% < 0.1% 폴리브롬화디페닐에테르 (PBDE) 0.1% < 0.1% 위에서 말한 제품의 일부 구성 요소는 아래의 내용과 같이 RoHS2 지침의 부속 문서에 따라 면제됩니다. 면제된 구성 요소의 예는 다음과 같습니다. 1.
주의 사항 및 경고. 1. 장치를 사용하기 전에 이 설명서를 빠짐없이 읽으십시오. 2. 이 설명서를 안전한 곳에 보관하십시오. 3. 모든 주의사항을 유의하고 모든 지침을 따르십시오. 4. LCD 디스플레이에서 45 cm 이상 떨어져 앉으십시오. 5. LCD 디스플레이를 운반할 때는 항상 조심하여 다루십시오. 6. 뒷면 덮개를 제거하지 마십시오. LCD 디스플레이에는 고압이 흐르는 부품이 들어 있습니다. 이 부품을 만지면 중상을 입을 수 도 있습니다. 7. 물 근처에서 이 장치를 사용하지 마십시오. 경고: 화재 또는 전기적인 쇼크의 위험성을 줄이려면, 이 기구를 비 또는 습기에 노출하지 마십시오. 8. LCD 디스플레이를 직사광선이나 다른 열원에 노출하지 마십시오. 빛 반사를 줄이려면 LCD 디스플레이를 직사광선이 비추는 곳을 피하여 놓으십시오. 9. 부드럽고 마른 헝겊으로 닦습니다.청소를 계속해야할 경우 설명서에 있는 “ 디스플레이 청소하기”를 참조하십시오. 10. 화면을 터치하지 마십시오.
20. 제조업체가 지정하거나 장치와 함께 판매한 카트, 스탠드, 삼각대, 브래킷 또는 테이블만을 사용하십시오. 카트를 사용할 경우 카트가 뒤집어져 상해를 입지 않도록 카트/장치를 함께 이동할 때는 조심하십시오. 21. 장기간 사용하지 않을 때는 장치의 플러그를 뽑아 두십시오. 22. 모든 수리는 유자격 수리기사에게 맡기십시오. 전원 코드 또는 플러그가 손상되었거나, 장치 안으로 액체를 쏟거나 물체를 떨어뜨렸거나, 장치가 비나 물에 젖었거나, 정상적으로 작동하지 않거나, 떨어뜨린 경우 수리가 필요합니다. 23. 환경 변화로 인해 화면에 습기가 낄 수 있습니다. 그러나 몇 분이 지나면 사라집니다.
차례 준수 정보 FCC 적합성 선언................................................................................... i 캐나다 산업성 규정................................................................................. i RoHS2 적합성 선언............................................................................... ii 주의 사항 및 경고..................................................................................iii 저작권 정보 제품 등록............................................................................................. 2 기록 보관........
저작권 정보 Copyright © ViewSonic® Corporation, 2018. 모든 권리는 저작권자의 소유입니다. Macintosh와 Power Macintosh는 Apple lnc의 등록 상표입니다. Microsoft, Windows및 Windows 로고는 미국 및 그 외 국가에서 Microsoft Corporation 의 등록 상표입니다. ViewSonic, 세 마리의 새 로고, OnView, ViewMatch,및 ViewMeter 는 ViewSonic Corporation 의 등록 상표입니다. VESA는 Video Electronics Standards Association의 등록 상표입니다. DPMS, DisplayPort 와 DDC는 VESA의 등록 상표입니다. ENERGY STAR® 는 U.S.Environmental Protection Agency(EPA) 의 등록 상표입니다 .
제품 등록 추가 제품 정보 및 차후 제품 필요에 대비해서 ViewSonic 웹사이트를 방문하여 제품을 온라인으로 등록하십시오. ViewSonic CD에도 제품 등록 양식이 있어 인쇄할 수 있습니다. 완료되면 관련 지역 ViewSonic 사무실로 팩스 또는 우편으로 보내십시오. 등록 양식을 찾으려면 디렉토리 ":\CD\Registration"을 사용하십시오. 제품을 등록하면 차후 고객 서비스가 필요할 때 이용할 수 있습니다. 이 사용설명서를 인쇄하여 "For Your Records(참조용)" 섹션 정보를 기입하십시오. LCD 디스플레이 제품 번호는 디스플레이 뒷면에 있습니다. 추가 정보는 설명서에 있는 "Customer Support(고객 지원)" 섹션을 참조하십시오. 기록 보관 제품 명칭: 모델 번호 : 문서 번호: 제품 번호: 구입 날짜: TD1711 ViewSonic Widescreen LCD Display VS17441 TD1711_UG_JPN Rev.
시작하기 ViewSonic® LCD 디스플레이를 구입해 주셔서 감사합니다. 중요 사항! 나중에 운반할 경우를 대비하여 제품 상자와 모든 포장 내용물들을 보관하십시오. 참고: 사용 설명서에 있는 “Windows”는 Microsoft Windows 운영 체제를 말합니다. 포장 내용물 중요 사항: 모든 포장 내용물을 보관하십시오. • LCD 디스플레이 • 전원 코드 • 오디오케이블 • D-Sub 케이블 • USB 케이블 • 빠른 시작 가이드 참고: 제공된 INF 파일은 Windows운영체제와 호환되며, ICM(lmage Color Matching) 파일은 정교한 화면 색상을 제공합니다. ViewSonic 사는 이 두 파일을 모두 설치할 것을 권장합니다.
빠른 설치 1. 비디오 케이블 연 • • • 2. LCD 디스플레이와 컴퓨터의 전원이모두 꺼져 있는지 확인하십시오. 필요한 경우 후면 패널 덮개를 여십시오. LCD 디스플레이의 비디오 케이블을 컴퓨터에 연결하십시오. 전원 코드 연결(필요한 경우 AC/DC 어댑터도 연결) * RS232 직렬 * RS232 serial포트 port * 3. LCD 디스플레이와 컴퓨터 전원 켜기 LCD 디스플레이의 전원을 켜고, 다시 컴퓨터의 전원을 켜십시오. 이 순서 (LCD 디스플레이를 컴퓨터보다 먼저)는 매우 중요합니다. 4. Windows 사용자: 타이밍 모드 설정(예: 1024 x 768) 해상도 및 화면 주사율 변경에 관한 설명은 그래픽 카드 사용자 안내서를 참조하십시오.설치를 완료했습니다. 5. 새로운 ViewSonic LCD 디스플레이가 주는 즐거움을 느껴보십시오.
하드웨어 설치 A. 받침대 부착 순서 B.
터치 기능 제어 3. 터치 기능을 사용하기 전에 , USB 케이블이 연결되었고 , Windows 운영 체제가 시작되었는지 확인하십시오 . 참고: 1. 터치 기능은 USB 케이블을 다시 꽂거나 컴퓨터가 수면 모드에서 다시 시작된경우에 재 작동하는데 약 5 초가 필요합니다 . 2. 터치 스크린은 동시에 최대 열 손가락까지만 감지합니다. 3. 화면을 터치할 때 커서가 정확하게 손가락을 따라가지 않으면 아래 단계에 따라 이를 보정하십시오. (OS: Windows 7, Windows 8, Windows 8.1 및 Windows 10 보정) 1. 제어판을 열고 하드웨어 및 소리를 연 후 태블릿 PC 설정을 엽니다. 2. 보정을 선택합니다. 3. 지시 사항에 따라 화면을 다시 보정합니다. 기울기 각도 조정 1.
보안 잠금장치 사용법 보안 커넥터는 모니터 뒷면에 있습니다. 설치 및 사용에 대한 자세한 내용. 다음은 참고용으로 제시한, 테이블에 잠금장치를 설치하는 예입니다.
벽걸이용 설치(선택 사항) 참고: UL Listed 벽면 설치 브래킷과만 사용 벽걸이 키트 또는 높이 조정판을 구하려면, ViewSonic® 또는 가까운 대리점에 문의하십시오. 기본 설치용 키트와 함께 제공된 설명을 참조하십시오. LCD 디스플레이를 탁상용에서 벽걸이용으로 전환하려면 다음을 따르십시오. 1. 전원 버튼이 꺼졌는지 확인한 후 전원 코드를 뽑으십시오. 2. 수건이나 담요 위에 LCD 디스플레이가 아래로 향하게 놓습니다. 3. 베이스를 제거합니다. (나사를 제거해야할 수도 있습니다.) 4. 디스플레이 후면에 있는 다음과 같은 VESA 장착 인터페이스(a,b,c)를 찾습니다 (디스플레이 장착 인터페이스는 “사양” 페이지 참조). 적절한 길이의 나사를 사용하여 VESA 호환 벽 장착 키드에 장착 브래킷을 부착합니다. a. b. 75mm c. 200mm 100mm 100mm 75mm 100mm 100mm 5.
LCD 디스플레이 사용 타이밍 모드 설정하기 타이밍 모드 설정은 화면 이미지의 품질을 최대화하고 눈의 피로를 최소화하는 데 중요합니다. 타이밍 모드는 해상도(예: 1024 x 768) 및 재생률(또는 수직 주파수, 예: 60 ㎐)로 구성되어 있습니다. 타이밍 모드를 설정한 후OSD컨트롤을 사용하여 화면 이미지를 조정하십시오. 최적의 이미지 품질을 위해 “사양” 페이지에 있는 LCD 디스플레이에 대한 지정된 권장 타이밍 모드를 사용하십시오. 타이밍 모드를 설정하려면: • 해상도 설정 : 시작 메뉴를 통해 “모양 및 개인 설정”에 액세스하여 해상도를 설정합니다. • 화면 주사율 설정 : 설명은 그래픽 카드 사용자 안내서를 참조하십시오. 중요: 그래픽 카드가 대부분의 LCD 디스플레이에 대한 권정 설정인 60Hz 수직 새로 고침 빈도로 설정되어 있는지 확인하십시오. 지원하지 않는 타이밍 모드로 설정하면 이미지가 표시되지 않을 수 있으며 이런 경우 “범위를 벗어남”이라는 메시지가 표시됩니다.
화면 이미지 조정하기 전면 제어 패널의 버튼을 사용하여 화면에 나타난 OSD 제어를 화면에 표시하고 조정합니다. 전원 켜기/끄기 전원 표시등 청색 배경=켜짐 황색=절전 모드 [1] 메인 메뉴를 표시하거나 제어 화면을 종료하고 조정 내용을 저장합니다. [2] 강조 표시된 제어에 대한 제어 화면을 표시합니다. 또한 자동 이미지 조정에 바로 가기 역할을 합니다. ▲/▼ 메뉴 옵션을 스크롤하여 표시된제어를 조정합니다. 밝기/명조 대비 (▼) / 오디오 조절 (▲) . 화면 이미지를 조정하려면 다음과 같이 하십시오: 1. 메인 메뉴가 나타나면 ,[1]버튼을 누르십시오. 참고: 모든 OSD 메뉴와 조정 화면은 약 15초 후에 자동으로 사라집니다. 이 시간간격은 설정 메뉴와 11페이지에 설명된 OSD 시간 초과 제어를 통해 조정할 수 있습니다. 2. 조정할 제어를 강조 표시하려면 , ▲또는▼을 눌러 메인 메뉴를 위 아래로 스크롤 하십시오. 3. 강조 표시된 제어를 선택하려면, 버튼 [2]를 누르십시오.
메인 메뉴 제어 위로 ▲ 및 아래로 ▼ 버튼을 사용하여 메뉴 항목을 조정하십시오. 참고: LCD OSD에 있는 기본 메뉴를 확인하고 아래 기본 메뉴 설명을 참조하십시오. 기본 메뉴 설명 참고: 이 절에 나열된 주 메뉴 항목은 모든 모델의 주 메뉴 전체를 표시합니다. 사용자 제품에 해당하는 실제 주 메뉴 세부사항은 사용자의 LCD OSD 주 메뉴 항목을 참조하십시오. A Audio Adjust (오디오 조절) 볼륨 조정, 음소거, 또는 한 개 이상의 소스가 있을 경우 입력 신호 사이를 전환합니다. Auto lmage Adjust (자동 이미지 조절) 는 화면 이미지 크기를 자동으로 조정하여 이미지를 중앙에 위치시킵니다. 참고:자동 이미지 조정은 대부분의 일반 비디오 카드와 작동합니다. 이 기능이 LCD 디스플레이에서 작동하지 않는 경우 비디오 재생률을 60 Hz 로 낮추고 해상도를 사전 설정 값으로 설정하십시오. B Brightness (밝기) 화면 이미지 배경의 어두운 정도를 조절합니다.
Input Select (입력 선택) LCD 디스플레이에 하나 이상의 컴퓨터가 연결되었을 때 입력 간에 전환합니다. M Manual Image Adjust (이미지 조정 ) 수동 이미지 조정 메뉴를 표시합니다. 다양한 이미지 품질 조정을 수동으로 설정할 수 있습니다. Memory Recall (메모리 복원) 사용 설명서의 사양에 있는 공장 사전 설정 타이밍 모드로 디스플레이가 작동할 경유 공장 설정으로 다시 전환합니다. 예외: 이 컨트롤은 언어 선택 또는 전원 잠금 설정에서 이루어진 변경 내용에 영향을 미치지 않습니다. S Setup Menu (설정 메뉴) 온스크린 디스플레이(OSD) 설정을 조정합니다. 전원 관리 이 제품은 3 분 동안 신호 입력이 없으면 검은색 화면의 대기 모드/끄지로 전환되어 전력 소비를 줄입니다.
기타 정보 사양 LCD 색상 필터 모니터 표면 TN 타입, a-si TFT 액티브 매트릭스 1280 x 1024 LCD, 0.264 mm 픽셀 피치 미터 단위: 43,2 cm 인치 단위: 17” (가시화면 17”) RGB 수직 띠 유리 표면: 눈부심 방지, 하드 코팅(3H) 터치 타입 1포인트 터치 제스처를 채택한 저항막 방식 기술 입력 신호 비디오 동기화 방식 RGB 아날로그(0.7/1.
1 퓨터 드래픽 카드에서 이 타이밍 모드를 초과하여 설정하지 마십시오; LCD 디스플레이에 영구 손상을 줄 수 컴 있습니다. *유 광 베젤이 있는 디스플레이의 경우 베젤이 주변광과 반짝이는 표면에 나오는 빛을 반사하여 시야를 방해할 수 있기 때문에 사용자는 이를 고려하여 디스플레이를 배치해야 합니다.
LCD 디스플레이 청소 • LCD 디스플레이의 전원이 꺼졌는지 확인하십시오. • 화면이나 케이스에 액체를 직접 뿌리거나 붓지 마십시오. 화면을 청소하려면: 1. 깨끗하고 부드럽고 보풀이 일지 않는 천으로 화면을 닦으십시오. 먼지와 티끌이 제거됩니다. 2. 여전히 더러우면 깨끗하고 부드럽고 보풀이 일지 않는 천에 암모니와나 알코올 성분이 없는 유리 세척제를 약간 적셔 화면을 닦으십시오. 케이스를 청소하려면: 1. 부드럽고 마른 천을 사용하십시오. 2. 여전히 더러우면 깨끗하고 부드럽고 보풀이 일지 않는 천에 암모니아나 알코올 성분이 없는 순한 비마모성 세척제를 약간 적셔 표면을 닦으십시오. 면책조항 • ViewSonic® 은 암모니아 또는 알코올 성분의 세척제를 LCD 디스플레이나 케이스에 사용하는 것을 권장하지 않습니다. 일부 화학 세척제는 LCD 디스플레이의 화면 및/또는 케이스에 손상을 입히는 것으로 알려져 있습니다.
문제 해결 전원이 안 들어올 때 • 전원 버튼 (또는 스위치)이 켜진 상태인지 확인하십시오. • A/C 전원 코드가 LCD 디스플레이에 올바르게 연결되었는지 확인하십시오. • 다른 전기 장치 (예: 라디오)를 전원 콘센트에 꽂아서 콘센트의 전압이 적절하게 공급되는지 확인해 보십시오. 전원이 켜졌으나 화면 이미지가 나오지 않을 때 • LCD 디스플레이와 함께 제공된 비디오 케이블이 컴퓨터의 뒷면에 있는 비디오 출력 포트에 연결되었는지 확인하십시오. 만일 비디오 케이블의 다른 한쪽 끝이 LCD디스플레이에 고정 부착된 상태가 아니라면, LCD 디스플레이와 연결된 부분이끼워졌는지 확인하십시오. • 밝기와 대비를 조정하십시오. 이상하거나 비정상적인 색상이 나올 때 • 빨간색, 녹색 또는 파란색 중에서 어느 색이든 나오지 않는다면, 비디오 케이블이 제대로 연결되었는지 확인하십시오. 케이블 커넥터 안의 핀이 없거나 부러졌다면 제대로 연결이 되지 않습니다. • LCD 디스플레이를 다른 컴퓨터에 연결해보십시오.
고객 지원 기술적인 지원이나 제품 서비스를 원하시면, 아래의 표를 참조하거나 해당 대리점에 문의하십시오. 주의 : 제품 번호가 필요합니다. 국가 / 지역 웹사이트 전화 전자메일 한국 ap.viewsonic.com/kr/ 080 333 2131 service@kr.viewsonic.
제한 보증 ViewSonic® LCD 디스플레이 보증 내용 ViewSonic은 제품 보증 기간 동안 자사 제품에 대해 소재나 제조기술에 결함이 없음을 보증합니다. 제품 보증 기간 동안 제품의 소재나 제조기술의 결함이 입증되면 ViewSonic은 자유 재량으로 해당 제품을 수리하거나 유사 제품으로 교환해드립니다. 교환 제품 또는 부품에는 재생또는 중고 부품이 포함될 수 있습니다. 보증 유효 기간 ViewSonic LCD 디스플레이는 광원을 포함하여 모든 부품에 대해 구입 국가에 따라 최초 구입일로부터 1 ~ 3 년을 보장합니다. 보증 대상 이 보증은 해당 제품의 첫 구입자에 대해서만 유효합니다. 보증 제외 대상 1. 일련 번호가 훼손, 변경 또는 제거된 제품. 2. 다음 원인으로 인해 발생한 손상, 기능 저하 또는 고장: a. 사고, 오용, 부주의, 화재, 수해, 번개 또는 기타 자연 재해, 승인되지 않은 제품 개조 또는 제품에 포함된 설명서 미준수. b. 운반시 발생한 제품 손상. c.
손해 제외 대상 ViewSonic의 책임은 제품의 수리 또는 교환 비용으로 제한됩니다. ViewSonic 은 다음에 대해 책임을 지지 않습니다. 1. 제품 결함으로 인한 다른 재산상의 손해, 사용의 불편함에 근거한 손해, 제품 가용성 손실, 시간 손실, 이익 손실, 사업 기회 손실, 신용 손실, 사업 관계 저촉 또는 기타 상업상의 손실(이와 같은 손해 가능성에 대해 충고한 경우에도 그러함). 2. 부수적이든 결과적이든 또는 다른 경우이든 기타 모든 손해. 3. 제3자에 의한 고객에 대한 손해 배상 요구. 4. ViewSonic 에서 승인하지 않은 사람에 의한 수리 또는 수리 시도. 주법의 효력 이 보증은 귀하에게 특정한 법적 권리를 부여하며 귀하에게는 주에 따라 다른 권리가 있을 수도 있습니다. 일부 주에서는 묵시적 보증에 대한 제한 및/또는 부수적 또는 결과적 손해에 대한 제외사항을 허용하지 않습니다. 따라서 위의 제한 및 제외사항은 귀하에게 적용되지 않을수도 있습니다.