VZ-CMP SERIES 19.5", 21.5" and 24" PROFESSIONAL LED CCTV MONITOR USER MANUAL Please read this manual thoroughly before use, and keep it handy for future reference.
CONTENTS Safety Instruction ....................................................................................................................................................................................... 3 1. Mark Indication & Substance ....................................................................................................................................................... 4 2. Warning .................................................................................................
SAFETY INSTRUCTION Important Safety Instruction 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. 17. Read all warnings. Follow all instructions to ensure longevity of monitor. Do not place the monitor near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers,stoves, or other heat generating devices.
SAFETY INSTRUCTION Important Safety Instruction Mark Indication and Substance CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol is intended to alert the user to the presence of uninsulated & dangerous voltage within the monitor’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
SAFETY INSTRUCTION Important Safety Instruction Caution • • • • • • • • • • • • • If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. Make sure to unplug the power cord before cleaning the monitor. Make sure to leave a gap between monitor and wall. Do not drop the monitor when moving it. Place your monitor in a location with low humidity and a minimum dust.
FCC RF INTERFERENCE STATEMENT Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
INSTALLATION Installation Tools The following tools may be required depending on your installation. Electronic Stud Finder Pencil Protective Eye-wear Level Phillips Screwdriver Assembly Components - provided Your ViewZ monitor is shipped with all proper installation hardware and components. If there are parts missing and/or damaged, please stop the installation and contact ViewZ USA at (888)-998-4399. 19.5", 21.5" and 23.
CONNECT EXTERNAL EQUIPMENTS Interface Input Ports The following image is the description of interface input ports of BNC Monitor q 1. 2. 3. 4. 5. 6. 8 w e r t y DC 12V IN HDMI IN VGA IN BNC (Composite) IN BNC (Composite) OUT Audio IN / OUT Visit the ViewZ USA website at https://www.viewzusa.
REMOTE FUNCTION Remote Controller 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Power Picture Freeze Up Left Menu Right Down Mute Input VGA Input Select YPbPr Input Select - Not Activate HDMI Input Select AV Input Select S-Video Input Select - Not Activate DVI Input Select - Not Activate q w e r t y u i o a s d f g h j Display image, sound and custom settings can be adjusted in OSD (On Screen Display) menu by Remote Controller. To adjust monitor setting value : 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
CONTROL AND FUNCTION On Monitor, Button Control y q 1. Source Select an input source 2. Menu 3. Enter the sub-menu, save the adjustment of submenu or exit the OSD / Select a menu on OSD 4. Left & Right ◄ (VOL) ► Change the value on selected menu 5. Up & Down ▲ ▼ Switch a menu on OSD w e r t 6. Power Monitor power on / off 7.
CONTROL AND FUNCTION Select Input Source AV1 AV2 VGA HDMI Press 'SOURCE' button on monitor or 'INPUT' button on remote controller Press▲ ▼ buttons to change input source Volume 22 Press◄ / ► buttons to adjust volume Detect Source Signal Message If you connect any input source, then monitor will display current input source resolution and frequency. User Manual Visit the ViewZ USA website at https://www.viewzusa.
CONTROL AND FUNCTION Picture PICTURE Contrast Brightness Tint Color Sharpness Color Tempera..
CONTROL AND FUNCTION OSD SYSTEM OSD Language OSD Duration Blue Screen Restore Defau.. English 10Sec On ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION OSD LANGUAGE Set the language of the OSD menu VALUE English, Deutsch, French Spanish, Italian OSD DURATION Set the OSD display time BLUE SCREEN Set the standby mode screen as blue or black (default) color RESTORE DEFAULT Reset the monitor settings to the factory default User Manual Visit the ViewZ USA website at https://www.viewzusa.
CONTROL AND FUNCTION Function FUNCTION Noise Reduction Auto Adjust Prevent Burni.. Middle On ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION NOISE REDUCTION1) Reduce noise of the display image AUTO ADJUST Fit the image size automatically 1) PREVENT BURNING VALUE LOW / MIDDLE / HIGH / DEFAULT / OFF Set periodic image retention ON / OFF 1) Only available in VGA input 14 Visit the ViewZ USA website at https://www.viewzusa.
CONTROL AND FUNCTION Sound SOUND Treble Bass Balance Sound Mode Auto Volume 0 Standard Off 50 50 ▲/▼ MOVE ◄/► SELECT(ADJUST) MENU RETURN FUNCTION VALUE BASS Adjust the bass level 0 ~ 100 TREBLE Adjust the treble level 0 ~ 100 BALANCE Adjust the balance SOUND MODE Select one of the presets AUTO VOLUME1) Set the automatic volume control -50 ~ +50 USER / SPORTS / MOVIE / MUSIC / STANDARD ON / OFF 1) Available in Composite ( video ) / HDMI input User Manual Visit the ViewZ USA website at h
MOUNTING GUIDE Wall Mounting (Optional) VZ-CMP monitors are suitable for VESA wall mount (not included in the delivery). M4 x L10 screws 1. VZ-19CMP, VZ-22CMP, VZ-24CMP : VESA WALL MOUNT 75mm x 75m Attention! VZ-CMP : You must use 4 * M4 x L10 screws to assemble this monitor and the wall mount bracket. WARNING ! If user uses screws longer than M4 x L10 mm, it may cause damage to the unit. Please use bolt of correct size and length as instructed.
SPECIFICATION Model No. VZ-19CMP VZ-22CMP VZ-24CMP Size & Type 19.5" 21.5" 24" Panel Type 19.5'' LED Backlit Monitor 21.5'' LED Backlit Monitor 24'' LED Backlit Monitor Pixel Pitch 0.2767 (H) x 0.2767(V) mm 0.2482 (H) x 0.2482(V) mm 0.2767 (H) x 0.2767 (V) mm Brightness 250 cd/m² 250 cd/m² 300 cd/m² LCD Contrast Ratio 1000 : 1(Typ.) Viewing Angle R/L : 85°/ 85° U/D : 80°/ 80° Display Color 16.
TROUBLESHOOTING GUIDE - Check the following before calling for service. - If the same problems continue after checking, contact the reseller you purchased the monitor from.
TERMS OF WARRANTY / RMA - The warranty period for this monitor is 3 years. The warranty will be voided for the scenarios listed below. - You can also download the manual and information of VIEWZ web site: VIEWZUSA.
NOTE 20 Visit the ViewZ USA website at https://www.viewzusa.
WARRANTY ViewZ USA LIMITED 3 YEAR WARRANTY What and Who is Covered by this Limited Warranty and for How Long ViewZ USA warrants this product to be free from defects in material and workmanship for 3 YEAR of the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What ViewZ USA Will Do At the sole option of ViewZ USA, ViewZ USA will repair or replace any product or product part that is defective.
