VZ-UNBS SERIES 49" and 55" PROFESSIONAL LED CCTV VIDEO WALL MONITOR USER MANUAL Please read this manual thoroughly before use, and keep it handy for future reference.
CONTENTS Safety Instruction ....................................................................................................................................................................................... 3 1. Mark Indication & Substance ....................................................................................................................................................... 4 2. Warning & Caution ........................................................................................
SAFETY INSTRUCTIONS Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. 16. Read all warnings. Follow all instructions to ensure longevity of monitor. Do not place the monitor near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other heat generating devices.
SAFETY INSTRUCTIONS Important Safety Instructions Mark Indication and Substance CAUTION : TO REDUCE THE RISK OF ELECTRICAL SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol is intended to alert the user to the presence of uninsulated & dangerous voltage within the monitor’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
SAFETY INSTRUCTIONS Important Safety Instructions Caution • • • • • • • • • • • • • If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. Make sure to unplug the power cord before cleaning the monitor. Make sure to leave a gap between monitor and wall. Do not drop the monitor when moving it. Place your monitor in a location with low humidity and minimal dust.
FCC RF INTERFERENCE STATEMENT Note This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.
INSTALLATION Installation Tools The following tools may be required or recommended. Stud Finder & Pencil Protective Eye-wear Level Ladder Phillips & Flathead Screwdriver Automatic Screwdriver Phillips & Flathead Screwdriver Bit Assembly Components - provided Your ViewZ monitor is shipped with all proper installation hardware and components. If there are parts missing and/or damaged, please stop the installation and contact ViewZ USA at (888)-998-4399.
FEATURES Features • • • • • • • • • • • • • • • • • Creates a seamless display effect in multi-screen splicing Supports m rows and n columns (1 ≤ m ≤ 15, 1 ≤ n ≤ 15) in splicing and 15 x15 at most Remote control of RS232 serial port: each unit supports one RS232 input and loop-out Integrated multi-channel video signal type - HDMI, DVI, VGA, DP, video daisy-chained by HDMI up to 15x15.
CONNECT EXTERNAL EQUIPMENTS Interface Input Ports The following image is the description of interface input ports w q er t y 1. 2. 3. 4. 5. 6. u u oa AUDIO OUT USB - For upgrading SW RS232 (RJ-45) IN - Serial Control / IR Receiver RS232 (RJ-45) OUT - A - Serial Control RS232 (RJ-45) OUT - B - Serial Control VGA IN 7. 8. 9. 10. 11. 12.
REMOTE FUNCTION Remote Controller 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. 13. 14. 15. POWER ON Number Key- For entering ID #s ID(0) - To setup the ID ARROW - OSD Control ENTER - To confirm current OSD value VGA - To select the VGA input source DVI - To select the DVI input source HDMI - To select the HDMI input source No Function - VIDEO/PLAY/PAUSE/STOP/REV./FWD/ PREV./NEXT.
DAISY CHAIN CONFIGURATION Video Wall Wiring Configurations - Daisy Chain If user wants to use external HDMI input source to be displayed on multiple units, the connection diagram of the video wall is as shown in the following figure (*Note - HDMI is the only source that daisy-chaining supports q w Cat 5 Cable HDMI Cable e r IR Receiver If you have multiple HDMI input sources, use a matrix to switch sources.
CONTROL AND FUNCTION Select Input Source Press 'SOURCE' button on monitor or on remote controller. Press ▲ / ▼ button to change input source and then press ENTER button to select input source on remote controller. If you connect any input source, monitor will display current input source resolution and frequency. 12 Visit the ViewZ USA website at https://www.viewzusa.
CONTROL AND FUNCTION Image ▲/▼ MOVE ◄/►ADJUST ENTER SELECT MENU RETURN PICTURE MODE DYNAMIC Reduce contrast and sharpness USER 1 & 2 Applies user selected values - brightness, contrast, VALUE sharpness, tint and color BRIGHTNESS Adjust the brightness 0 ~ 100 CONTRAST Adjusts the difference between the 0 ~ 100 lightest and darkest parts of the image SHARPNESS Adjusts projected image sharpness 0 ~ 100 TINT Adjusts the image color balance of red 0 ~ 100 and green COLOR Adjust the color valu
CONTROL AND FUNCTION Image ▲/▼ MOVE ◄/►ADJUST ENTER SELECT MENU RETURN FUNCTION VALUE H-POSITION 1) Adjust the horizontal picture position 1 ~ 100 V-POSITION Adjust the vertical picture position 1 ~ 100 ClOCK 1) Adjust the number of horizontal picture elements 1 ~ 100 PHASE Adjust the vertical noise of screen image 1 ~ 100 1) 1) AUTO ADJUST Adjust the screen automatically Press ENTER button on remote controller to set auto adjust for screen 1) Only available in VGA input 14 Visit the
CONTROL AND FUNCTION Image ▲/▼ MOVE ◄/►ADJUST ENTER SELECT MENU RETURN FUNCTION VALUE H_Addr: 1 ~ 15, V_Addr: 1 ~ 15 Soft ID Monitor's physical location 1) Wall H Addr The horizontal starting number of video wall monitors 12) Wall V Addr The vertical starting number of video wall monitors 12) Wall H End3) The horizontal location value of video wall monitors 1 ~ 15 Wall V End4) The vertical location value of video wall monitors 1 ~ 15 Video Wall Set Switch selected/entire monitors as one o
CONTROL AND FUNCTION Image - Video Wall Setup for HDCP ▲/▼ MOVE ◄/►ADJUST ENTER SELECT MENU RETURN FUNCTION Generate ID Creates the logical identification code (Identifier) IR Control Sees the horizontal and vertical address of selected monitor Close OSD Close ID OSD window Identifier The logical identification code created by 'Generate ID' Soft ID The Physical location address of video wall system monitors VALUE Variable Variable H_Addr:1 ~ 15, V_Addr:1 ~ 15 1) Press the 'ID (0)' button on th
CONTROL AND FUNCTION Setup Update Firmware Software Restore Default ▲/▼ MOVE ◄/►ADJUST ENTER SELECT MENU RETURN FUNCTION MENU LANGUAGE Set the language of the OSD menu VALUE English/Spanish/French/ Portuguese RESTORE DEFAULT SOFTWARE UPDATE EDID SWITCH 1) Reset the monitor settings to the factory default YES/NO Update the monitor firmware by default YES/NO Change EDID version for HDCP Input 1.4/ 2.0 EDID 1.4 1) You can use USB drive to upgrade firmware of monitor.
MOUNTING GUIDE Wall Mounting (Optional) VZ-UNBS monitors are suitable for universal wall mount (not included). Minimum 4 * M6 x L12 screws for VZ-49UNBS / 55UNBS 1. VZ-49UNBS & VZ-55UNBS : Universal WALL MOUNT 600 x (100 x 4) mm WARNING ! If user uses screws bigger and longer than M6 x L12 mm for VZ-49UNBS & VZ-55UNBS it may cause damage to the unit. Please use bolt of correct size and length as instructed. Mounting Safety ! At least two people are recommended to safely install the mount and monitor.
RS232 (RJ-45) PIN ASSIGNMENT PIN MAP The following image is the description of RJ-45 PIN MAP GND RXD RS232 (DP9) RJ45 RXD (Received Data) 3 2 GND (Groud) 5 5 If your video wall system requires an unified control by the central control (do not use provided video wall screen control software), please use the provided RJ-45(RS-232) cables to configure the sytem. If necessary, you can make your own RJ-45(RS-232) cables based on the above pin map. If you have further questions, please contact ViewZ.
SPECIFICATION LCD Model No. VZ-49UNBS VZ-55UNBS Size & Type 49" 55" Panel Type 49'' LED Backlit Monitor 55'' LED Backlit Monitor Pixel Pitch (mm) 0.55926 (H) x 0.55926 (V) mm 0.630 (H) x 0.630 (V) mm Brightness 450 cd/m² 500 cd/m² Contrast Ratio 5000 : 1 5000 : 1 Viewing Angle 178° / 178° Display Color 16.7 Million Colors Response Time < 8ms (Gray to Gray) < 8ms (Gray to Gray) Resolution Active Display Area 1920 (H) x 1080 (V) 1073.8 (H) x 604.0 (V) mm 1209.6 (H) x 680.
TROUBLESHOOTING GUIDE - Check the following before calling for service. - If the same problems continue after checking, contact the reseller you purchased the monitor from. At start We recommend that you test with different input sources when you have trouble with the current input source. If symptom persists, follow the instructions below. After following the instructions below, please contact us at 1-888-99-VIEWZ.
TERMS OF WARRANTY / RMA - The warranty period for this monitor is 3 years. The warranty will be voided for the scenarios listed below. - You can also download the manual and information on VIEWZ web site: VIEWZUSA.COM When power feed to the monitor exceeds capacity and causes damage. Accident, Abuse, Misuse, Neglect, Fire, Water/liquids, Lightning or any act of nature. Cases of Non-Warranty Coverage Damaged by dropping, throwing and hitting the monitor.
NOTE User Manual Visit the ViewZ USA website at https://www.viewzusa.
WARRANTY ViewZ USA LIMITED 3 YEAR WARRANTY What and Who is Covered by this Limited Warranty and for How Long ViewZ USA warrants this product to be free from defects in material and workmanship for 3 years to the original owner of this product. The limited warranty is valid only for the original purchaser of the product. What ViewZ USA Will Do At their sole discretion, ViewZ USA will repair or replace any product or product part that is defective.
