Quick Guide

®
®
module and antenna
How to install WLAN
Step 1
Step 2
Step 3
Step 4
Step 3
Preparation before the installation setup
Step 5
Step 2 Step 4
8
InstalltheWLANUSBmodule(EMIO-1533-00A1)andsecureit
InserttheWLANportconnectorintotheantenna
Gentlyconnecttheminicoaxialcableofthe
AttachtheWLANboardtoboardcabletotheWLANUSBmodule.
ThefrontsidepanelofVZ-PRO-MINIhasfour
Ifusinganetwork,connecttheEthernetcableto
AttachtheEthernetcablefromLANportofthe
PlugtheaudiocableintotheLine-outjackon
PlugthepowercableintotheDC-Injackon
PlugtheVideoWallMinipowercordintoan
mustbedone,allcomponentsandnetworkare
powerofVZ-PRO-MINI.
portnumbersonVideoWallMini(e.g.videowall
TheVZ-PRO-MINIhasaHDMI-INportwhichcansupportexternal
digital/videosourcessuchasNotebookPC,DVDplayerandetc.
Formoreinformation,pleasecontractoursalesrepresentative.
Formoreinformationon
thisandotherViewZ
products,pleasevisit
www.viewzusa.com
Removethe3G/3.5Gantennaholecoverfromtherightsidepanel
1.ReadfirstthisQuickSetupDiagram
2.ThisQuickSetupDiagramisonlyintendedto
5.VZ-PRO-MINIisalittlebitheavy.Avoid
3.Ensurethatallitems,peripherals,cables
4.MakesurethepowercordofVZ-PRO-MINI
6.Donotplacethesystemonunstable
7.Ifyouareunfamiliarwiththeinstallation
sectionbeforetakinganyaction.
beusedasareferenceguideforsettingup
droppingthesystemaccidentally,handle
andtoolsneededarepresentbefore
isunpluggedbeforetheinstallationsetup.
surfacesorwalls.
processconsultqualifiedpersonnel.
usingtheVZ-PRO-MINIsystem.Itisnot
ittightlydirectlyonitsbodychassisand
startingtheinstallationsetup.
requiredorintendedtobeastep
bystepprocedureforthesetup.
avoidholdingitonanyexternalI/Oconnectors.
Gentlyconnecttheminicoaxialcableofthe3G/3.5Gport
ofthechassis. connectortotheminiRFconnectoronthe3G/3.5Gmodule.
Oncethe3G/3.5Gmodulehasbeenfullyinserted,pushdownthe Insertthe3G/3.5Gportconnectorintotheantennaholefromthe
withtwoscrews.ThenremovetheantennaWLANholecover
holefromtheinsideofthechassis.Insertthe
WLANportconnectortotheminiRF
Thenattachtheotherendofthecabletothe“JUSB2_3”pin
HDMIports(HDMI1~HDMI4).ConnecttheHDMI
theLANportonVideoWallMini.Thenconnectthe
controlServertotheLANportonHub/Router.
VZ-PRO-MINI.
VZ-PRO-MINI.
electricaloutlet.Makesureallotherconnections
properlysetupandreadybeforeturningonthe
displaynumber1and2mustbeconnectedtoHDMI
Copyright©VIEWZUSA.Allrightsreserved.
fromtherightsideI/Opanelofthechassis.
washer,fastenitwiththenutandinstallthe
connectorontheWLANUSBmodule.
headerofthemainboard.
cablesofvideowalldisplaystoitsdesignatedHDMI
otherendofthecabletotheHub/Router.
1andHDMI2portsrespectively).
externalantenna.
moduleuntilthescrewholealignswiththestandoffhole.Then insideofthechassis.Insertthewasherandfastenitwiththenut
securethemodulewithscrews. theninstalltheexternalantenna.
Quick Setup Diagram
Connecting the video wall display
Connecting to the network via cable wire
Connecting the control server
Connecting the speaker
Plug in the power adapter
ViewZUSA
177W.OrangethorpeAve.,Placena,CA92870
Tel.714.996.1177,Fax.714.996.1138
Specicaonsubjecttochangewithoutnoce.
[e-mail]
q
w
e
r
t