VIGO INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE (MODEL VG06041) ! SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information. Always observe the instructions indicated by these symbols. ! WARNING Instructions that, if ignored, could result in death or serious personal injury caused by incorrect handling or installation of the product. These instructions must be observed for safe installation.
INSTALLATION INSTRUCTIONS FOR SHOWER DOOR OWNER'S MANUAL PLEASE READ INSTRUCTIONS BEFORE PROCEEDING 1 10 Packing List 1. Wall mount bracket (2pc) 2. Fixed panel holders (2pc) 3. Rollers (4pc) 4. Fixed panel (1pc) 5. Door (1pc) 6. Handle assembly (1pc) 7. Fixed panel bottom clip (1 pc) 8. Door bottom guide (1 pc) 9. Door threshold (1pc) 10. Door stopper (2pc) 11. Structural rail (1pc) 12. Door and fixed panel seal strip (2pc) 13. Door seal strip (3pc., 1 of each is extra) 14.
1. WALL MOUNT BRACKET ASSEMBLY 2. FIXED PANEL HOLDER 7. FIXED PANEL BOTTOM CLIP 6. HANDLE ASSEMBLY 98021 8. DOOR BOTTOM GUIDE 98022 5. DOOR 97015-48x74 97015-60x66 97015-60x74 97015-72x74 98020 98019 98018 4. FIXED PANEL 3. ROLLERS 97016-48x74 97016-60x66 97016-60x74 97016-72x74 9. DOOR THRESHOLD 98023 10.DOOR STOPPER 95005-48 95005-60 95005-72 98024 adjustment on bottom, make sure it is set to 10mm or 3/8" 11. STRUCTURAL RAIL 12. DOOR AND FIXED PANEL SEAL STRIP 98025 13.
! WARNING WE STRONGLY RECOMMEND THAT A LICENSED PROFESSIONAL INSTALL THIS STANDING SHOWER CABIN AND INCLUDE THE ASSISTANCE OF A SECOND PERSON TO INSTALL THE DOOR UNIT. INSTALLATION OF THE SHOWER DOORS BY AN INEXPERIENCED PERSON MAY RESULT IN GLASS BREAKAGE AND CONSEQUENTLY, CAUSE PERSONAL INJURY OR DEATH. BEFORE STARTING Compare items on your invoice with what you have received. Carefully review the Packing List on page 2. If any items are missing, please call Vigo Industries at 1-866-591-7792.
IMPORTANT Verify that the overall size of the shower door opening is appropriate for the shower enclosure. Due to individual site variations, exact guidelines for every situation cannot be supplied. The recommended framing and dimensional requirements are shown for a typical application and may vary depending on the site requirements. To prevent damage to the finish, you should protect the shower cabin bottom with a cardboard protector before beginning the installation.
11 DOOR PANEL (#5) INSIDE OF THE SHOWER 10 11 4 12 2 2 10 OUTSIDE OF THE SHOWER VIEW FROM TOP INSIDE OF THE SHOWER 12 4" 12 4 8 7 4 8 OUTSIDE OF THE SHOWER 14 OUTSIDE OF THE SHOWER 7 14 VIEW FROM TOP FIG. 4 FIG.3 B. INSTALLING THE FIXED PANEL 1. Remove the fixed panel (#4) and structural rail (#11) assembly from the shower door opening. Find the center of the marked circumference on the wall. Mark holes on the wall for the mounting screws.
PLATE PLATE HEX SCREW 17 15 BRACKET BODY FIG. 5 18 8 18 16 7 FIG. 6 C. INSTALLING THE DOOR 1. Remove the rollers (#3) from the box, note that these are fully installed. Carefully unthread the cap with a small head allen key. You will see a big hex screw, this is referred to as the roller height adjustment screw. Use the provided allen key to unscrew the adjustment screw and dismantle the roller. Place the screw through door panel top holes and attach the two top rollers onto the door panel (#5).
INSIDE OF THE SHOWER OUTSIDE OF THE SHOWER 5 5 3 3 5 VIEW FROM TOP 12 FIG. 7 ROLLER HEIGHT ADJUSTMENT SCREW FIG. 9 FIG. 8 5 5 4 9 8 FIG. 10 D. INSTALLING THE THRESHOLD IMPORTANT IN CASE THE THRESHOLD IS CUT TOO SHORT, USE THE THRESHOLD EXTENSION CLIP (#14) TO EXTEND THE THRESHOLD ACCORDINGLY. 1. 2. 3. Place the threshold (#9) to the bottom door guide (#8).
8 9 8 7 8 FIG. 11 E. INSTALLING THE HANDLE 1. 2. Unscrew the handle holders from the handle assembly (#6). Place the handle to the position on the door. Place plastic washers (supplied) on each side of the door. [SEE FIG.12] Tighten the handle nuts from inside the shower. 3. 5 FIG. 12 6 F. INSTALLING THE WATER SEAL STRIP 1. 2. Place the seal strip (#13) to the door and to the fixed panel, respectively. [SEE FIG.
5 5 13 This end must look inside the shower 4 13 FIG. 13 G. APPLYING THE SILICONE 1. Apply clear silicone caulking along the wall and floor of the shower enclosure interior. [SEE FIG.14] Apply clear silicone caulking along the fixed panel and threshold of the shower enclosure interior. 2. FIG.
MODEL VG06041 11
! IMPORTANT - WAIT 24 HOURS BEFORE USING SHOWER - DO NOT ALLOW WATER TO DIRECTLY HIT DOOR SEAL STRIPS. CLEANING INSTRUCTIONS FOR THE SHOWER CABIN AND DOOR PANEL A. B. C. D. Use mild liquid household cleaners to keep metal surface bright and clean. Rinse well and dry with a clean cloth. Remove dust with a soft, damp cloth. Use rubbing alcohol to clean and remove grease, oil, paint, and ink. Accidental scratches or stains will rarely show.
IMPORTANT ROLLER ADJUSTMENTS TO ACCOMMODATE OUT OF SQUARE OPENINGS NOTE: There is a 3/8" adjustment in the roller to use in the case that your walls are not plumb and level. Using an allen key, you will be able to adjust the roller to accommodate for the variance. 1. 2. 3. 4. 5. Loosen the hex screw to allow for movement. Then place the allen key in the small hex hole as shown and roll it to the right or left to make the adjustment. [See Fig.1] Fig. 1A displays the 3 different positions.
ROLLER (3) The small hex hole on on the roller will be facing up on this roller. The small hex hole on on the roller will be center right on this roller. ROLLER (3) A B WALL WALL STRAIGHT WALLS WALL DIRECTION STRAIGHT WALL ROLLER "A" SMALL HEX HOLE DIRECTION ROLLER "B" SMALL HEX HOLE DIRECTION UP FIG.
The small hex hole on on the roller will be facing up on this roller. The small hex hole on on this roller will be adjusted to meet the gap. ROLLER (3) ROLLER (3) A B TILTS IN AT TOP (EXAGGERATED FOR PURPOSE OF DEPICTION) WALL OUT OF PLUMB WALL TOP ANGLED WALL WALL DIRECTION TOP ANGLED ROLLER "A" SMALL HEX HOLE DIRECTION ROLLER "B" SMALL HEX HOLE DIRECTION UP ADJUST AS NEEDED FIG.
The small hex hole on on this roller will be adjusted to meet the gap. The small hex hole on on the roller will be facing up on this roller. ROLLER (3) ROLLER (3) A B WALL OUT OF PLUMB WALL TILTS IN AT BOTTOM (EXAGGERATED FOR PURPOSE OF DEPICTION) BOTTOM ANGLED WALL WALL DIRECTION ROLLER "A" SMALL HEX HOLE DIRECTION ROLLER "B" SMALL HEX HOLE DIRECTION BOTTOM ANGLED ADJUST AS NEEDED UP FIG.
SHOWER ENCLOSURE LIMITED LIFETIME WARRANTY EFFECTIVE JANUARY 1, 2010 only to the original owner or end-user for personal household use. For commercial uses, additional limitations apply.
