Owner manual

ManualsBrandsVigo ManualsFor HomeVG09017K1

DIMENSIONS

FLOOR

34"

19 5/8"

FLOOR

18"

VANITY SPECIFICATIONS

VANITY COMPONENTS

Model VG09017K1

MODEL # VANITY VANITY VANITY

WIDTH HEIGHT DEPTH

VG09017K1 19 5/8" 34" 18"

MODEL VG09017K1

FEATURES









PACKING LIST

Vanity Assembly











Sink



TOLL FREE: (866) 591 - 7792

E-Mail: techmail@vigoindustries.com

www.vigoindustries.com

For warranty purposes contact our toll free number:

Summary of content (7 pages)

PAGE 1
VANITY SPECIFICATIONS VANITY COMPONENTS Model VG09017K1 MODEL VG09017K1 FEATURES PACKING LIST Vanity Assembly Sink DIMENSIONS MODEL # VANITY WIDTH 19 5/8" VG09017K1 VANITY HEIGHT 34" VANITY DEPTH 18" For warranty purposes contact our toll free number: TOLL FREE: (866) 591 - 7792 E-Mail: techmail@vigoindustries.com 18" 19 5/8" 34" www.vigoindustries.
PAGE 2
19 1/2" DIMENSIONS 29 1/2" TOP VIEW WITH DOORS OPEN 34" 19 5/8" FLOOR 18" FRONT VIEW 16 3/4" 9 3/4" 17" 5 1/8" 25" 8" 4 1/2" 2 3/4" 11 1/4" FLOOR FLOOR SIDE VIEW BACK VIEW MODEL VG09017K1 THE MEASUREMENTS IN INCHES ARE ROUNDED TO THE NEAREST 1/8" 2
PAGE 3
ROUGHING-IN 2 3/4" 11 1/4" 17" 5 1/8" 25" Should be at the same height as the center of the 2"x6" Backing Material 9 3/4" 8" 4 1/2" Open space for Rough-In Plumbing FLOOR BACK VIEW NOTE: Vigo reserves the right to change or alter their products or warranty. Vigo recommends using the physical attributes and dimensions of the actual product and not the installation instructions when preparing the site for your roughing-in.
PAGE 4
PREPARE SITE NOTE: This is the recommended installation for wall mount and freestanding vanities. NOTE: To properly secure the vanity, the center of the required 2x6 backing material must be the correct height from the floor. This will be your desired height. OPTION A FRONT-NOTCH ADJUSTABLE BASED OFF DESIRED HEIGHT Measure and mark your desired height up from the floor. Make sure to remove the distance of the top of the vanity without the sink to the center on the 2 mounting vanity brackets, 4 1/2".
PAGE 5
PACKAGE CONTENTS CAP - 2PC. VANITY PLASTIC ANCHOR - 2PC. COVER (WOOD) 1PC. ASSEMBLY WASHER 2PC. MIRROR SCREW 2PC. PLASTIC ANCHOR MIRROR BRACKET 1. Select the vanity location and mark holes on the wall for mounting screws. Remove the vanity, drill holes, stick anchors. Place washers to the screws and screw unit to the wall. This should be drilled into your 2"x6" backing material. Place covers to the screws.
PAGE 6
OPTIONAL: STEP 2 OF INSTALLATION INSTRUCTIONS When installing your faucet it is highly recommended to remove the top drawer. This will allow you to have access to the hollow pin and supply lines of the faucet in order for you to complete your installation. Vigo brand vanities have two typical styles for the drawer assembly. Vigo offers multiple methods for removal of the drawers. Below are the typical methods to remove the top drawer. UNSCREW OPTION A 1 Pull the drawer out.
PAGE 7
VANITY COMPONENTS LIMITED WARRANTY EFFECTIVE JANUARY 1, 2010 original owner or end-user for personal household use. For commercial uses, additional limitations apply. VIGO warrants the Product to be free from defects in workmanship and materials under normal use and service for a period of five (5) years from the initial date of purchase by the owner or end-user, contractor, or builder, from VIGO or an authorized VIGO dealer.