User Manual

ManualsBrandsVigo ManualsFor HomeVG09018K

DIMENSIONS

VANITY SPECIFICATIONS

VANITY COMPONENTS

Model VG09018K

MODEL # VANITY VANITY VANITY

WIDTH HEIGHT DEPTH

VG09018K 30 1/2" 19 3/8" 20"

MODEL VG09018K

FEATURES











PACKING LIST

Vanity Assembly













Mirror





Sink



FLOOR

19 3/8"

30 1/2"

FLOOR

20"

TOLL FREE: (866) 591 - 7792

E-Mail: techmail@vigoindustries.com

www.vigoindustries.com

For warranty purposes contact our toll free number:

21 5/8"

29 1/2"

Summary of content (7 pages)

PAGE 1
VANITY SPECIFICATIONS VANITY COMPONENTS Model VG09018K MODEL VG09018K FEATURES PACKING LIST Vanity Assembly Mirror Sink DIMENSIONS MODEL # VG09018K VANITY WIDTH 30 1/2" VANITY HEIGHT 19 3/8" 29 1/2" VANITY DEPTH 20" 1" TOLL FREE: (866) 591 - 7792 21 5/8" For warranty purposes contact our toll free number: E-Mail: techmail@vigoindustries.com 20" 30 1/2" 19 3/8" www.vigoindustries.
PAGE 2
DIMENSIONS 21 5/8" 29 1/2" 1" 19 3/8" 30 1/2" FLOOR 20" 13 3/8" FRONT VIEW 29 3/4" 3 1/8" 5 5/8" 15" 3 1/8" 7 5/8" 25 5/8" +/- 1/8" 7 3/8" ADJUSTABLE 20 1/4" FLOOR ADJUSTABLE BACK VIEW FLOOR SIDE VIEW MODEL VG09018K THE MEASUREMENTS IN INCHES ARE ROUNDED TO THE NEAREST 1/8" 2
PAGE 3
ROUGHING-IN 25 5/8" +/- 1/8" 3 1/8" 5 5/8" 7 3/8" Open space for Rough-In Plumbing ADJUSTABLE Should be at the same height as the center of the 2"x6" Backing Material 3 1/8" 7 5/8" 20 1/4" FLOOR ADJUSTABLE BACK VIEW NOTE: Vigo reserves the right to change or alter their products or warranty. Vigo recommends using the physical attributes and dimensions of the actual product and not the installation instructions when preparing the site for your roughing-in.
PAGE 4
PREPARE SITE NOTE: This is the recommended installation for wall mount and freestanding vanities. NOTE: To properly secure the vanity, the center of the required 2x6 backing material must be the correct height from the floor. This will be your desired height.. OPTION A FRONT-NOTCH ADJUSTABLE BASED OFF DESIRED HEIGHT Measure and mark your desired height up from the floor. Make sure to remove the distance of the top of the vanity without the sink to the center on the 2 mounting vanity brackets, 7 5/8".
PAGE 5
PACKAGE CONTENTS ASSEMBLY COVER 4PC. VANITY SCREW 4PC. MIRROR 1. Select the vanity location and mark holes on the wall for mounting screws. Remove the vanity, drill holes, stick anchors. Place washers to the screws and screw unit to the wall. This should be drilled into your 2"x6" backing material. Place covers to the screws. Plastic anchor Washer Screw SCREW (2PC.) VANITY BRACKETS -2PC. SCREW - 6PC. PLASTIC ANCHOR - 10PC. WASHER 4PC. WALL SCREW LOCATION Cover PLASTIC ANCHOR (2PC.
PAGE 6
OPTIONAL: STEP 2 OF INSTALLATION INSTRUCTIONS When installing your faucet it is highly recommended to remove the top drawer. This will allow you to have access to the hollow pin and supply lines of the faucet in order for you to complete your installation. Vigo brand vanities have two typical styles for the drawer assembly. Vigo offers multiple methods for removal of the drawers. Below are the typical methods to remove the top drawer. UNSCREW OPTION A 1 Pull the drawer out.
PAGE 7
VANITY COMPONENTS LIMITED WARRANTY EFFECTIVE JANUARY 1, 2010 original owner or end-user for personal household use. For commercial uses, additional limitations apply. VIGO warrants the Product to be free from defects in workmanship and materials under normal use and service for a period of five (5) years from the initial date of purchase by the owner or end-user, contractor, or builder, from VIGO or an authorized VIGO dealer.