User guide

ManualsBrandsVigo ManualsFor HomeVG09036K

DIMENSIONS

VANITY SPECIFICATIONS

VANITY COMPONENTS

Model VG09036K

MODEL # VANITY VANITY VANITY

WIDTH HEIGHT DEPTH

VG09036K 24 1/4" 23 5/8" 18 3/8"

MODEL VG09036K

FEATURES











PACKING LIST

Vanity Assembly









Mirror











Sink



23 5/8"

24 1/4"

FLOOR

18 3/8"

TOLL FREE: (866) 591 - 7792

E-Mail: techmail@vigoindustries.com

www.vigoindustries.com

For warranty purposes contact our toll free number:

27 1/2"

15 3/4"

6 1/4"

Summary of content (7 pages)

PAGE 1
VANITY SPECIFICATIONS VANITY COMPONENTS Model VG09036K MODEL VG09036K FEATURES PACKING LIST Vanity Assembly Mirror Sink DIMENSIONS MODEL # VG09036K VANITY WIDTH 24 1/4" VANITY HEIGHT 23 5/8" 6 1/4" 27 1/2" 15 3/4" For warranty purposes contact our toll free number: VANITY DEPTH 18 3/8" TOLL FREE: (866) 591 - 7792 E-Mail: techmail@vigoindustries.com 18 3/8" 24 1/4" 23 5/8" www.vigoindustries.
PAGE 2
DIMENSIONS 5" 12 5/8" 3 5/8" 17 3/4" 20" +/- 1/8" FLOOR BACK VIEW 6 1/4" 27 1/2" 15 3/4" 18 3/8" 24 1/4" 23 5/8" 7 1/8" FLOOR FRONT VIEW SIDE VIEW MODEL VG09036K THE MEASUREMENTS IN INCHES ARE ROUNDED TO THE NEAREST 1/8" 2
PAGE 3
ROUGHING-IN 5" 12 5/8" 3 5/8" ADJUSTABLE Open space for Rough-In Plumbing 17 3/4" 20" +/- 1/8" Should be at the same height as the center of the 2"x6" Backing Material FLOOR BACK VIEW NOTE: Vigo reserves the right to change or alter their products or warranty. Vigo recommends using the physical attributes and dimensions of the actual product and not the installation instructions when preparing the site for your roughing-in.
PAGE 4
PREPARE SITE NOTE: This is the recommended installation for wall mount and freestanding vanities. NOTE: To properly secure the vanity, the center of the required 2x6 backing material must be the correct height from the floor. This will be your desired height. OPTION A FRONT-NOTCH ADJUSTABLE BASED OFF DESIRED HEIGHT Measure and mark your desired height up from the floor. Make sure to remove the distance of the top of the vanity without the sink to the center on the 2 mounting vanity brackets, 5".
PAGE 5
PACKAGE CONTENTS ASSEMBLY SHELF SCREW 2PC. VANITY MIRROR MIRROR BRACKET 1. Once the product has been unpacked your first step will be to assemble the unit. Select the vanity location and measure distance between hanging units. Mark holes on the wall for the wall brackets. Remove brackets, drill holes, sink anchors and screw the brackets to the wall. This should be drilled into your 2"x6" backing material. 1 VANITY BRACKETS -2PC. SCREW 6PC. PLASTIC ANCHOR - 8PC. SCREW 2PC. PLASTIC ANCHOR 2PC.
PAGE 6
OPTIONAL: STEP 2 OF INSTALLATION INSTRUCTIONS When installing your faucet it is highly recommended to remove the top drawer. This will allow you to have access to the hollow pin and supply lines of the faucet in order for you to complete your installation. Vigo brand vanities have two typical styles for the drawer assembly. Vigo offers multiple methods for removal of the drawers. Below are the typical methods to remove the top drawer. UNSCREW OPTION A 1 Pull the drawer out.
PAGE 7
VANITY COMPONENTS LIMITED WARRANTY EFFECTIVE JANUARY 1, 2010 original owner or end-user for personal household use. For commercial uses, additional limitations apply. VIGO warrants the Product to be free from defects in workmanship and materials under normal use and service for a period of five (5) years from the initial date of purchase by the owner or end-user, contractor, or builder, from VIGO or an authorized VIGO dealer.