Owner manual

ManualsBrandsVigo ManualsFor HomeVG0905K1

DIMENSIONS

MODEL # VANITY VANITY VANITY

WIDTH HEIGHT DEPTH

VG09005K1 44" 18 5/8" 22"

FLOOR

44"

18 5/8"

FLOOR

22"

VANITY SPECIFICATIONS

VANITY COMPONENTS

Model VG09005K1

MODEL VG09005K1

FEATURES











PACKING LIST

Vanity Assembly













Sink



TOLL FREE: (866) 591 - 7792

E-Mail: techmail@vigoindustries.com

www.vigoindustries.com

For warranty purposes contact our toll free number:

Summary of content (7 pages)

PAGE 1
VANITY SPECIFICATIONS VANITY COMPONENTS Model VG09005K1 MODEL VG09005K1 FEATURES PACKING LIST Vanity Assembly Sink DIMENSIONS MODEL # VG09005K1 VANITY WIDTH 44" VANITY HEIGHT 18 5/8" VANITY DEPTH 22" For warranty purposes contact our toll free number: TOLL FREE: (866) 591 - 7792 E-Mail: techmail@vigoindustries.com 44" 22" 18 5/8" www.vigoindustries.
PAGE 2
DIMENSIONS 44" ADJUSTABLE 8 5/8" 18 5/8" 17 1/4" 43 3/4" 19 5/8" 32 3/8" FLOOR FRONT VIEW 22" OPENING FOR THE DRAIN & WATER SUPPLY 13 1/2" 12 3/4" ADJUSTABLE 4 1/2" HOLES FOR THE MOUNTING SCREWS 21 5/8" 30" to center of clip +/- 1/8" FLOOR FLOOR BACK VIEW SIDE VIEW MODEL VG09005K1 THE MEASUREMENTS IN INCHES ARE ROUNDED TO THE NEAREST 1/8" 2
PAGE 3
13 1/2" Open space for Rough-In Plumbing 12 3/4" ADJUSTABLE 4 1/2" ROUGHING-IN 30" to center of clip +/- 1/8" Should be at the same height as the center of the 2"x6" Backing Material FLOOR BACK VIEW NOTE: Vigo reserves the right to change or alter their products or warranty. Vigo recommends using the physical attributes and dimensions of the actual product and not the installation instructions when preparing the site for your roughing-in.
PAGE 4
PREPARE SITE NOTE: This is the recommended installation for wall mount and freestanding vanities. NOTE: To properly secure the vanity, the center of the required 2x6 backing material must be the correct height from the floor. This will be your desired height. OPTION A FRONT-NOTCH ADJUSTABLE BASED OFF DESIRED HEIGHT Measure and mark your desired height up from the floor. Make sure to remove the distance of the top of the vanity without the sink to the center on the 2 mounting vanity brackets, 4 1/2".
PAGE 5
PACKAGE CONTENTS ASSEMBLY VANITY COVER (WOOD) 1PC. HANDLE WITH (2) SHORT SCREWS 1. Once the product has been unpacked your first step will be to assemble the unit. Select the vanity location and measure distance between hanging units. Mark holes on the wall for the wall brackets and two mounting screws. Remove brackets, drill holes, stick anchors and screw the brackets to the wall. This should be drilled into your 2"x6" backing material. VANITY BRACKETS (2PC.
PAGE 6
OPTIONAL: STEP 2 OF INSTALLATION INSTRUCTIONS When installing your faucet it is highly recommended to remove the top drawer. This will allow you to have access to the hollow pin and supply lines of the faucet in order for you to complete your installation. Vigo brand vanities have two typical styles for the drawer assembly. Vigo offers multiple methods for removal of the drawers. Below are the typical methods to remove the top drawer. UNSCREW OPTION A 1 Pull the drawer out.
PAGE 7
VANITY COMPONENTS LIMITED WARRANTY EFFECTIVE JANUARY 1, 2010 original owner or end-user for personal household use. For commercial uses, additional limitations apply. VIGO warrants the Product to be free from defects in workmanship and materials under normal use and service for a period of five (5) years from the initial date of purchase by the owner or end-user, contractor, or builder, from VIGO or an authorized VIGO dealer.