Installation Guide

ManualsBrandsVigo ManualsKitchen ApplianceAll-in-One Undermount Stainless Steel 32 in. 0-Hole Double Bowl Kitchen Sink Set with Stainless Steel Faucet

SINK SPECIFICATIONS

DOUBLE BOWL Undermount

Model VG3221R

MODEL # BOWL SIZE SINK DEPTH EXTERIOR GAUGE

VG3221R

32" x 20 3/4"

15 3/4" x 18 3/4"

13" x 16 1/2"

DIM.

NOMINAL DIMENSIONS

TOP VIEW

FRONT VIEW

20 3/4" [526mm]

16 1/2" [420mm]

13" [330mm]

15 3/4" [400mm]

9" 18 3/4" [475mm]

PACKING LIST

- SINK

- CUT-OUT TEMPLATE

- MOUNTING HARDWARE

9 1/4"

[184mm]





FEATURED MODEL VG3221R

9" & 7" BOWL DEPTH

FEATURES

 18 gauge, stainless steel

 304 Nickel - Bearing Content

 Long-lasting, easy-to-clean, satin finish

 Sound-deadening insulation

 Available in right configuration (big bowl is on the

right) or left configuration (big bowl is on the left)

 Rear drain placement

 50mm radius corners on big bowl

 45mm radius corners on small bowl

32" [813mm]

18 1/2" [470mm]

[235mm]

[229mm]

7 1/4"

[178mm]

Summary of content (6 pages)

PAGE 1
SINK SPECIFICATIONS DOUBLE BOWL Undermount Model VG3221R FEATURED MODEL VG3221R 9" & 7" BOWL DEPTH FEATURES 18 gauge, stainless steel 304 Nickel - Bearing Content Long-lasting, easy-to-clean, satin finish Sound-deadening insulation Available in right configuration (big bowl is on the right) or left configuration (big bowl is on the left) Rear drain placement 50mm radius corners on big bowl 45mm radius corners on small bowl PACKING LIST NOMINAL DIMENSIONS MODEL # BOWL SIZE VG3221R 15 3/4" x 18 3/4" 9"
PAGE 2
Installation instructions Undermount Sinks Before you begin: Please carefully read these instructions. Unpack and inspect the sink carefully. Do not install the sink if it is damaged. Save all original packaging and receipts. Check and follow all local plumbing codes. General Recommendations: Read installation and maintenance instructions, thoroughly before installation.
PAGE 3
Installation Instructions Please carefully read complete instructions before beginning installation. Only a professional stone fabricator is qualified to perform this installation. Note: These instructions are for installation with solid surface, composite material countertops. Vigo recommends professional countertop installers and is not responsible for damage to the countertop or sink during installation. ! Do not cut the sink opening with traditional saw cut method. 1.
PAGE 4
6. Loosely attach mounting brackets to the countertop, parallel to the cutout opening using the supplied mounting screws and nuts. Mounting screws with brass inserts are supplied with the sink, however, countertop material vary and the correct type of fasteners should be recommended by your installer or supplier. 7. Clean sink flange and underside of cutout area of countertop, making sure that the area is smooth and free of grease. MUST use 100% silicone for this installation.
PAGE 5
Care and Maintenance ALWAYS preventative cleaning. affect the appearance of your sink. abrasive such as Comet. up over time with a mild solution of vinegar and water followed by a thorough flushing with water. grain. NOT RECOMMENDED FOR MIRROR FINISH. NEVER develop rust spots in the stainless steel surface. finish of your sink. the finish of your sink. sink. Silver cleaners can also contain acids that will damage the sink surface.
PAGE 6
KITCHEN SINK LIMITED LIFETIME WARRANTY EFFECTIVE JANUARY 1, 2010 end-user for personal household use. For commercial uses, additional limitations apply. VIGO warrants the Product to be free from defects in workmanship and materials under normal use and service for the period commencing from the initial date of purchase by the owner or end-user, contractor, or builder, from VIGO or an authorized VIGO dealer, through the lifetime of the original owner or end-user.