© Sims VIGOR INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE (MODEL VG06051) /\ SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information. Always observe the instructions indicated by these symbols. /A\ WARNING Instructions that, if ignored, could result in death or serious personal injury caused by incorrect handling or installation of the product. These instructions must be observed for safe installation. /\ CAUTION The instructions for the following unit i
HTTP: Aww industriousness. com Packing List 1-866-501-7702 1 Wall mount bracket (1pc) 2 Fixed panel holders (2pc) 3. Rollers (4pc) 4. Big front fixed panel (1pc) 5. Small front fixed panel (1pc) INSTALLATION INSTRUCTIONS FOR SHOWER ENCLOSURE OWNER'S MANUAL PLEASE READ INSTRUCTIONS BEFORE PROCEEDING Side glass panel (1pc) Door (1pc) Comer bracket (2pc) A Handle assembly (1pc) 10. Fixed panel bottom clip (1 pc) 11. Bottom door guide (1 pc) 12. Door threshold (1pc} 13. Left threshold end cup (1pc) 14.
HTTP: Aww industriousness. com 1-886-581-7782 1. WALL MOUNT BRACKET ASSEMBLY 98018 Co 2. FIXED PANEL HOLDER 98026 Gr 8. ROLLERS 4. BIG FRONT FIXED PANEL 98020 9702248 6702260 @; 5. SMALL FRONT FIXED PANEL 97021 6. SIDE GLASS PANEL 97019 7. DOOR 9702048 97020-50 8. CORNER BRACKET 98027 9. HANDLE ASSEMBLY 98021 FIXED PANEL BOTTOM CLIP XA ~T 11. BOTTOM DOOR GUIDE 98020 12. DOOR THRESHOLD 95007-48 95007-80 ES 13. LEFT END CUPS 98008 pe 14. RIGHT END CUPS 98009 = 15. DOOR STOPPER 28024 16.
HTTP: Aww industriousness. com A WARNING 1-866-501-7782 WE STRONGLY RECOMMEND THAT A LICENSED PROFESSIONAL INSTALL THIS SHOWER CABIN AND INCLUDE THE ASSISTANCE OF A SECOND PERSON TO INSTALL THE DOOR UNIT. INSTALLATION OF THE SHOWER DOORS BY AN INEXPERIENCED PERSON MAY RESULT IN GLASS BREAKAGE AND, CONSEQUENTLY, CAUSE PERSONAL INJURY OR DEATH. BEFORE STARTING Compare items on your invoice with what you have received. Carefully review the Packing List on page 2.
HTTP: WWW industriousness. com PREPARATION STEPS TO FOLLOW BEFORE INSTALLATION 1-866-501-7792 1. Remove the plastic layer from the base border (if needed). Do Not remove the plastic layer off the plastic platform of the base. 2. Properly apply silicone to the wall and base joints. © IMPORTANT Verify that the overall size of the shower door opening is appropriate for the shower enclosure. Because of the hole locations on the structural rail, cutting the rail is strongly not advised (see page 3 diagram).
HTTP: Aww industriousness. com 1-866-501-7702 7. Place the side glass panel with the structural rail into desired position. Use the level to correct position assembly. 8. Mark holes on the wall for the side glass support 9. Mark the circumference location for the wall mount bracket 10. Remove the side glass panel (#6) and the structural rail Drill holes into the wall where marked and place plastic anchors (#24) in them. 11. Unscrew plate from the wall mount bracket body using the hex key (FIG 4). 12.
HTTP: Aww industriousness. com 1-866-501-7702 B. INSTALLING THE BIG FRONT FIXED PANEL 1. Screw the fixed pane! bottom clip (#10) to the big front fixed panel Place thin gaskets on each side of the panel. [SEE FIG.6] 2. Place the side seal strip (#18) on the big front fixed panel (#4) from the side of the wall. 3. Place the big front fixed panel on the shower opening. 4. Screw the big front fixed panel to the structural rail (#16) with the fixed panel holders [SEE FIG.6 &FIG.7] 5.
C. INSTALLING THE SMALL FRONT FIXED PANEL 1. Align the small front fixed panel (#5) to the shower opening 2. Unscrew the corner brackets (#8) [SEE FIG.8] 3. Align the comer brackets to their respective positions from inside the shower. Place the comer plates on the outside of the shower. 4. Screw in the corner plates to the comer brackets with the provided screw from inside the shower. D. INSTALLING THE THRESHOLD 1. Seal the end cup bottoms with clear silicone caulk. 2.
HTTP: Aww industriousness. com 1-866-501-7702 E. INSTALLING THE DOOR 1. Screw the top rollers (#3) to the door [SEE FIG.10] 2. Align the door guide (#11) onto the door. 3. Hold the door in the vertical-level position. Mark the location of the bottom door guide on the floor. 4. Remove the door from the structural rail. Mark holes on the floor for the mounting screws. Drill the holes and place plastic anchors (#25) inside them. 5. Screw the door guide to the floor with screws 6.
HTTP: Aww industriousness. com 1-866-501-7702 F. INSTALLING THE HANDLE Unscrew the handle holders from the handle 2. Align the handle to its respective door position with a plastic washer on each side of the door. [SEE FIG.12] 3. Tighten the handle holders from the inside of the shower cabin. G. INSTALLING THE WATER STRIP Place the seal strip to the door and to the glass. [SEE FIG.13] H. APPLYING THE SILICONE 1. Apply silicone caulk along the wall and floor of the shower enclosure interior. [SEE FIG.14] 2.
HTTP: Aww industriousness. com 1-866-501-7702 I. INSTALLING THE HANDLE 1. Install hex screw covers (#26) to the hex screws that mount the hinges and glass supports. CLEANING INSTRUCTIONS FOR THE SHOWER CABIN AND DOOR PANEL A. Use mild liquid household cleaners to keep metal surface bright and clean. Rinse well and dry with a clean cloth. B. Remove dust with a soft, damp cloth. C. Use rubbing alcohol to clean and remove grass, oil, paint, and ink. D. Accidental scratches or stains will rarely show.
HTTP: Aww industriousness. com 1-866-501-7702 VIGOR INDUSTRIES, LLG ("VIGOR) SHOWER ENCLOSURE LIMITED LIFETIME WARRANTY EFFECTIVE JANUARY 1, 2010 VIGOR offers the following limited warranty on each of its Shower Enclosure products* (the “Product”) and the components thereof. This warranty extends only to the original owner or end-user for personal household use. For commercial uses, additional imitations apply.