VIGO INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE (MODEL VG06061) ! SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information. Always observe the instructions indicated by these symbols. ! WARNING Instructions that, if ignored, could result in death or serious personal injury caused by incorrect handling or installation of the product. These instructions must be observed for safe installation.
INSTALLATION INSTRUCTIONS FOR STANDING SHOWER CABIN OWNER'S MANUAL PLEASE READ INSTRUCTIONS BEFORE PROCEEDING Packing List 1. Wall connector (2pc) 2. Structural arm (2pc) 3. Support assembly (2pc) 4. Side glass panel (with hinge slots, 1pc) 5. Side glass panel (without hinge slots, 1pc) 6. Side seal strip (2pc) 7. Glass support (4pc) 8. Hinge (2pc) 9. Bottom rail(3 pc) 10. Door magnetic seal strip (2pc) 11. Bottom corner joint (2pc) 12. Handle assembly (1pc) 13. Door (1pc) 14.
1. WALL CONNECTOR 2. STRUCTURAL ARM 98001 6. SIDE SEAL STRIP 98004 12. DOOR HANDLE ASSEMBLY 21. HEX SCREW COVER 96040 13. DOOR 98039 4. SIDE GLASS PANEL 18. PHILLIPS SCREW 3/4" 98033 22. CLEAR PVC SHIM 23. ALLEN KEY PACK MISC MISC MODEL VG06061 5. SIDE GLASS PANEL 97001-36 97001-38 97001-40 97001-42 9. BOTTOM RAIL - 3pc. 95001-36 95001-38 95001-40 95001-42 14. THROUGH HINGE DOOR SIDE SEAL STRIP 97007-24 97007-25 17. HEX SCREW 1 5/8" 98035 98015 98014 94001 16.
* - GLASS AND HARDWARE - NO SHOWER BASE (FULLY INSTALLED) #4- SIDE GLASS PANEL (97001) #5- SIDE GLASS PANEL (97006) #13- DOOR (97007) MODEL DIM. "A" DIM. "B" DIM. "C" DIM.
! WARNING WE STRONGLY RECOMMEND THAT A LICENSED PROFESSIONAL INSTALL THIS SHOWER CABIN AND INCLUDE THE ASSISTANCE OF A SECOND PERSON TO INSTALL THE DOOR UNIT. INSTALLATION OF THE SHOWER DOORS BY AN INEXPERIENCED PERSON MAY RESULT IN GLASS BREAKAGE AND, CONSEQUENTLY, CAUSE PERSONAL INJURY OR DEATH. BEFORE STARTING Compare items on your invoice with what you have received. Carefully review the Packing List on page 2. If any items are missing contact Vigo Industries at 1-866-591-7792.
PREPARATION STEPS TO FOLLOW BEFORE INSTALLATION 1. Remove the plastic layer from the base border (if needed). Do NOT remove the plastic layer off the plastic platform of the base. 2. Properly apply silicone to the wall and base joints. 3. Make sure to read corresponding base instructions carefully prior to install on the Vigo Brand Shower Door System. Failure to do so can cause water leakage and bodily harm.
STUD FIG.2 FIG.2A THIS EDGE LOOKS INSIDE OF THE SHOWER 9 A B TOP REMOVES TO INSTALL 3/4" SCREW 18 THIS EDGE LOOKS OUTSIDE OF THE SHOWER 11 FIG.3 ALUMINUM COVER INSIDE INSIDE CORNER JOINT CAP OUTSIDE OUTSIDE FIG.
B. 1. 2. 3. HINGE INSTALLATION Clean the glass surface on the side glass panel (#4) where the hinges (#8) are to be installed with rubbing alcohol. Position hinges on the side glass panel. [SEE FIG.4] Place a shim between the glass and the hinge on the bottom. The metal should not rest on the glass. [SEE FIG.4A] Place gaskets on each side of the side glass panel. Screw the hinges to the side glass panel with the hex key (supplied).
C. 1. 2. 3. 4. 5. 6. 7. 8. 9. INSTALLING SIDE GLASS PANEL (PART #4) Arrange glass to the preferred configuration. (see diagram on page 5) These instructions are for a right side door opening configuration. Select the door opening location on the shower cabin. Install the side seal strip (#6) to the wall side of the hinged side glass panel (#4). [SEE FIG.
D. 1. 2. 3. 4. INSTALLING THE WATER SEAL STRIP TO DOOR PANEL Clean the door glass panel (#13) edge where the door side seal strip (#14) is to be installed with rubbing alcohol. [SEE FIG.7] Verify that the soft flange of the seal strip faces toward the inside of the shower cabin before seal strip installation. Install the seal strip according to the diagram. See Note: A. Leave the extra top of the seal strip that is overlapping the glass and cut at finish of install. NOTES: 1.
E. 1. 2. 3. 4. 5. 6. 7. ! WARNING DOOR PANEL INSTALLATION REQUIRES TWO OR MORE PEOPLE TO ASSIST INSTALLING THE DOOR Make sure you have the door right side up. The distance at the top is slightly larger than the distance at the bottom. [SEE FIG.8] Clean the door (#13) glass surfaces where the hinges (#8) are to be installed with rubbing alcohol. Place magnetic seal strip (#10) to the panel. The magnetic side should be facing the inside and the clear side be facing the outside.
F. 1. 2. 3. 4. 5. 6. INSTALLING SIDE GLASS PANEL (PART #5) Install the side seal strip (#6) to the wall side of the side glass panel (#5). Install the magnetic side seal strip (#10) to the door side. The magnetic side should be facing the outside and the clear side be facing the inside. Be sure to place the seal strip (#6) 10mm from the bottom of the glass. [SEE FIG.9] Installing the magnetic seal strip prior to locating the place for the glass support allows for proper seal.
G. 1. 2. 3. 4. 5. 6. 7. INSTALLING THE SIDE & FRONT PANEL SUPPORT Install the support assembly (#3) onto the side glass panel (#4) approximately two-thirds away from the wall. Use hex key to tighten to screws. [SEE FIG.11] Install the support assembly to the structural arm (#2) and wall connector (#1). Make sure it's level. Mark the holes on the wall for the mounting screws for the wall connector. Remove the support assembly. Drill holes into respective marks and put plastic anchors (#19) in them.
H. 1. 2. 3. 4. INSTALLING PRE-CUT BOTTOM DOOR SEAL STRIP Clean the door glass panel (#13) edge where the door bottom side seal strip (#15) is to be installed with rubbing alcohol. [SEE FIG.12] Verify that the soft flange of the seal strip faces toward the inside of the shower cabin before seal strip installation. Install the seal strip according to the diagram. NOTE: If the seal strip is not flat or twisted, use hot water and a hair dryer to apply minimal heat and press the seal strip back into position.
13 10 13 FIG.13 15 10 15 FIG.13A J. 1. HANDLE INSTALLATION Assemble the door handles (#12) to the door (#13). [SEE FIG.14] 13 12 FIG.14 K. INSTALLING HEX SCREW COVERS 1. Install hex screw covers (#21) to the hex screws that mount the hinges, wall connectors, and glass supports.
MODEL VG06061
CLEANING INSTRUCTIONS FOR THE SHOWER CABIN AND DOOR PANEL A. B. C. D. Use mild liquid household cleaners to keep metal surface bright and clean. Rinse well and dry with a clean cloth. Remove dust with a soft, damp cloth. Use rubbing alcohol to clean and remove grease, oil, paint, and ink. Accidental scratches or stains will rarely show. If they do show, they can be easily removed with a liquid automobile polish.
SHOWER ENCLOSURE LIMITED LIFETIME WARRANTY EFFECTIVE JANUARY 1, 2010 only to the original owner or end-user for personal household use. For commercial uses, additional limitations apply.