VIGO INDUSTRIES INSTALLATION GUIDE FOR SHOWER ENCLOSURE (MODEL VG06063) ! SAFETY PRECAUTIONS This Installation Guide uses the following symbols to indicate important information. Always observe the instructions indicated by these symbols. ! WARNING Instructions that, if ignored, could result in death or serious personal injury caused by incorrect handling or installation of the product. These instructions must be observed for safe installation.
MODEL VG06063 GEMINI INSTALLATION INSTRUCTIONS FOR SHOWER ENCLOSURE PLEASE READ INSTRUCTIONS BEFORE PROCEEDING 1 Parts List 1. Wall connector (2pc) 2. Structural arm (2pc) 3. Support assembly (2pc) 4. Side glass panel with hinge slots (2pc) 5. Side seal strip (2pc) 6. Glass support (4pc) 7. Hinge (4pc) 8. Bottom rail (3 pc) 9. Door magnetic seal strip (2pc) 10. Bottom corner joint (2 pc) 11. Handle assembly (2 sets) 12. Door (2 pc) 13. Door side seal strip (2pc + 1pc is extra) 14.
2. STRUCTURAL ARM 1. WALL CONNECTOR 7. HINGE ASSEMBLY 6. GLASS SUPPORT 98004 11. DOOR HANDLE ASSEMBLY 95001-42 95001-47 DOOR 96002 96001 10.CORNER JOINT 94001 14. DOOR BOTTOM SEAL STRIP 13. THROUGH HINGE DOOR SIDE SEAL STRIP 97002-12 98014 9. MAGNETIC SEAL STRIP 8. BOTTOM RAIL 98015 12. 97001-42 97001-47 98003 98002-42 98002-47 5. SIDE SEAL STRIP 4. SIDE PANEL 3. SUPPORT ASSEMBLY 98001 96004 15. HEX SCREW 1 1/8" 96035 96003 16. HEX SCREW 1 5/8" 17.
! WARNING WE STRONGLY RECOMMEND THAT A LICENSED PROFESSIONAL INSTALL THIS SHOWER ENCLOSURE AND INCLUDE THE ASSISTANCE OF A SECOND PERSON TO INSTALL THE DOOR UNIT. INSTALLATION OF THE SHOWER DOORS BY AN INEXPERIENCED PERSON MAY RESULT IN GLASS BREAKAGE AND, CONSEQUENTLY, CAUSE PERSONAL INJURY OR DEATH. - Handle fragile items with care to prevent personal injury or material damage. - The glass panels are tempered and cannot be cut. Never attempt to do so.
PREPARATION STEPS TO FOLLOW BEFORE INSTALLATION 1. Remove the plastic layer from the base border (if needed). Do NOT remove the plastic layer off the plastic platform of the base. 2. Properly apply silicone to the wall and base joints. 3. Make sure to read corresponding base instructions carefully prior to install on the Vigo Brand Shower Door System. Failure to do so can cause water leakage and bodily harm.
INSTALLATION STEPS A. 1. INSTALLING THE BOTTOM RAIL Remove the aluminum cover from the front piece of the bottom rail by sliding it out. A1 ALUMINUM COVER INSIDE OUTSIDE 2. Remove top of the corner joint. Slide the bottom corner joint (2 pieces) (#10) onto the bottom rail (3 pieces) (#8). A2 THIS EDGE LOOKS INSIDE OF THE SHOWER TOP REMOVES TO INSTALL 3/4" SCREW 8 10 THIS EDGE LOOKS OUTSIDE OF THE SHOWER 3. Align the bottom rail and corner joint to the desired position on the shower base.
4. Seal the bottom rail with clear silicone caulk and center its sides to the base. A4 B A 8 5. Clip the aluminum cover to the front piece of the bottom rail making sure the lower side faces the inside of the shower. Silicone the underneath portion of the corner joint caps and put them on the corner joints.
B. 1. INSTALLING SIDE GLASS PANEL Install the side seal strip (#5) to the wall side of the side glass panel (#4). Make sure to leave a 3/8" gap at the bottom. B1 5 5 3/8" [10mm] 4 4 WALL SIDE MAKE SURE TO LEAVE A GAP OF 3/8" [10MM] FROM THE BOTTOM OF THE GLASS 2. Screw in the glass support (#6) to the side glass panel using the hex key (supplied) making sure to slide it back as far as possible from the glass before you tighten. The part that connects to the wall should face in.
3. Place the side glass panel into the bottom rail (#8). Use the level to position the side glass panel correctly. Make sure the seal strip is against the wall. Mark holes on the wall for the mounting screws. B3 8 4. Remove the side glass panel. Drill holes into respective marks and insert plastic anchors (#19) inside them. ! Not necessary if installing into studs. Studs are the preferred means of installation, anchors can pull out of the wall causing property damage and bodily harm. B4 19 8 5.
C. 1. HINGE INSTALLATION Clean the glass surface on the side glass panel (#4) where the hinges (#7) are to be installed with rubbing alcohol. Place gaskets on each side of the side glass panel (#4). Position hinges on the side glass panel.
2. Place a shim between the glass and the hinge on the bottom. The metal should not rest on the glass.
3. Screw the hinges to the side glass panel with the hex key (supplied).
D. 1. INSTALLING THE DOOR SIDE SEAL STRIPS Clean the door glass panels (#12) edges where the door side seal strips (#13) are to be installed with rubbing alcohol. Place the seal strips according to the diagram. Verify that the lips of all seal strips face toward the inside of the shower cabin before seal strip installation. NOTES: 1. If the seal strip is not flat and is twisted, soak the strip in hot water and press the seal strip back into position. 2.
! WARNING DOOR PANEL INSTALLATION REQUIRES TWO OR MORE PEOPLE TO ASSIST E. INSTALLING THE DOOR 1. Clean the door (#12) glass surfaces where the hinges (#7) are to be installed with rubbing alcohol. Do not install the handle first, this is dangerous and may cause the glass to break. Install the top hinge first for safety and ease of install. Position the door onto the hinges. Place a thin gasket (supplied) on each side of the door between the glass and hinge while holding the door in place.
3. Make sure the doors are level from the end. If the doors are not level, adjust the hinge positions until the doors are level. These being level is imperative to the installation and will guarantee a tight seal. 12 E3 THIS SIDE MUST BE LEVEL E4 4. Clean the door glass panels (#12) edges where the door magnetic seal strips (#9) and the door bottom seal strips (#14) are to be installed with rubbing alcohol. Cut the seal strips according to the diagram.
F. 1. INSTALLING THE SIDE PANEL SUPPORTS Install the support assembly (#3) onto the side glass panel (#4) approximately two-thirds away from the wall. Use hex key to tighten to screws. F1 WALL SIDE PANEL 3 OUTSIDE OF THE CABIN WALL INSIDE VIEW 2. Install the support assembly to the structural arm (#2) and wall connector (#1). Make sure it's level. Mark the holes on the wall for the mounting screws for the wall connector.
3. Remove the support assembly. Drill holes into respective marks and put plastic anchors (#18) in them. ! Not necessary if installing into studs. F3 WALL 18 SIDE PANEL 3 4. Replace wall connector to proper position. Screw it in to the wall with 1 1/8" screws (#15). F4 WALL LEVEL 1 15 2 SIDE PANEL 3 5. Slide the structural arm (#2) into the wall connector (#1). Tighten all set screws. Repeat steps 1 through 5 to install the other support assembly to the other side glass panel.
G. 1. HANDLE INSTALLATION Assemble the door handles (#11) to the doors (#12).
H. 1. APPLYING THE SILICONE Apply clear silicone caulking to the inside between the wall and side seal strip. Apply clear silicone caulk to the inside between the bottom of side glass panels (#4) and bottom rail. Apply clear silicone caulk around the inside perimeter of the bottom rail. 2. Apply clear silicone caulk to the seal strip connections of the door bottom seal strip (#14) and the door magnetic seal strip (#9) and door side seal strip (#13).
I. 1. INSTALLING HEX SCREW COVERS Install hex screw covers (#20) to the hex screws that mount the hinges, wall connectors, and glass supports.
! IMPORTANT - WAIT 24 HOURS BEFORE USING SHOWER - DO NOT ALLOW WATER TO DIRECTLY HIT DOOR SEAL STRIPS. CLEANING INSTRUCTIONS FOR THE SHOWER CABIN AND DOOR PANEL 1. Use a mild liquid household cleaner to keep metal surfaces bright and clean. Rinse well and dry with a soft, clean cloth. 2. Remove dust with a soft, damp cloth. 3. Use a standard household window cleaner to clean the glass panels. 4.
SHOWER ENCLOSURE LIMITED LIFETIME WARRANTY EFFECTIVE JANUARY 1, 2010 only to the original owner or end-user for personal household use. For commercial uses, additional limitations apply.