Installation Guide

ManualsBrandsVIGO ManualsFarmhouse/Apron Kitchen SinksCasement Front Farmhouse Matte Stone 30 in. Single Bowl Kitchen Sink

SINK SPECIFICATIONS

SINGLE BOWL Farmhouse

Model VGRA3018SL

NOMINAL DIMENSIONS

TOP VIEW

FRONT VIEW

30" [761mm]

28 1/2" [724mm]

18" [455mm]

FEATURED MODEL VGRA3018SL

9 5/8" BOWL DEPTH

FEATURES

 Solid surface, pure acrylic

 10mm radius corners

 Elegant and functional drain grooves

 Long-lasting, easy-to-clean, glossy interior and

matte exterior finish

 Center drain placement

 Reversible for flat apron front or slotted apron front

PACKING LIST

- SINK

- STRAINER

16 1/2" [419mm]



[90 mm]

MODEL # BOWL SIZE SINK DEPTH EXTERIOR

VGRA3018SL 9 5/8"28 1/2" x 16 1/2"

30" x 18"

9 5/8"

[243mm]

8 3/8"

[212mm]

NOTE: Due to the nature of the material,

models can differ up to 5 mm from the listed

dimensions. We advise that you do not cut

your countertop based off of the dimensions

in the specifications area of the website, but

instead wait until your sink arrives to

measure and cut the countertop to ensure a

perfect fit.

This Sink comes with Sink VGRA3018SL and

Strainer VGSTRAINERFH.

NOTE: Customer needs to select the flat or

grooved front and proceed accordingly.

NOTE: DIMENSIONS MAY VARY UP TO 1/8"

Summary of content (18 pages)

PAGE 1
SINK SPECIFICATIONS SINGLE BOWL Farmhouse Model VGRA3018SL FEATURED MODEL VGRA3018SL 9 5/8" BOWL DEPTH FEATURES Solid surface, pure acrylic 10mm radius corners Elegant and functional drain grooves Long-lasting, easy-to-clean, glossy interior and matte exterior finish Center drain placement Reversible for flat apron front or slotted apron front PACKING LIST - SINK STRAINER NOMINAL DIMENSIONS MODEL # VGRA3018SL BOWL SIZE SINK DEPTH EXTERIOR 28 1/2" x 16 1/2" 9 5/8" 30" x 18" 30" [761mm] TOP VIEW
PAGE 2
Installation instructions Farmhouse Sinks General Recommendations: Read installation and maintenance instructions thoroughly before installation. Inspect your sink for any noticeable damage before installation. Check all local applicable plumbing and building codes.
PAGE 3
Installation Options: Vigo Farmhouse series sinks offer installation options depending on your design. Undermount Installation Flush mount Installation Figure 1 Figure 2 Above counter Installation Figure 3 Caution: All installation types need to allow room for faucet installation. Ensure adequate clearance behind the sink for any faucet and backsplash, as well as full range of motion for faucet spouts and handles. Typical undermount installation with 1/4" reveal recommended.
PAGE 4
1. Prepare the sink base cabinet Farmhouse sinks require custom order sink base cabinets with a front cutout to accommodate a 10" deep sink. Build structural supports on the inside frame of the sink base cabinet. The structural supports must support the weight of the sink and any attachments such as garbage disposals. When the sink is placed onto the cabinet support, make sure the top of the sink is evenly flush against the bottom of the countertop.
PAGE 5
Care and Maintenance ALWAYS preventative cleaning. affect the appearance of your sink. up over time with a mild solution of vinegar and water followed by a thorough flushing with water. NEVER finish of your sink. the finish of your sink. sink. Silver cleaners can also contain acids that will damage the sink surface.
PAGE 6
ACRYLIC SINK LIMITED LIFETIME WARRANTY EFFECTIVE AUGUST 1, 2014 VIGO offers the following limited warranty on each of its Acrylic / Resin Sink products* (the owner or end-user for personal household use. For commercial uses, additional limitations apply.
PAGE 7
VGRA3018SL VGRA3018SL Surface solide, acrylique pur Emplacement du drain central tablier avant LISTE DES ARTICLES DIMENSIONS NOMINALES VGRA3018SL 28 1/2" x 16 1/2" 30" x 18" 9 5/8" 30" [761mm] 16 1/2" [419mm] 18" [455mm] 28 1/2" [724mm] [90 mm] dimensions. Nous vous conseillons de ne VUE DE DESSUS dimensions dans le domaine des 9 5/8" [243mm] 8 3/8" [212mm] coupez le comptoir pour ajustement parfait. Filtre VGSTRAINERFH.
PAGE 8
ayant une surface solide. La pose de comptoir sur des blocs de boucher, du granite, du marbre ou de revendeur d'armoires. des robinets, ni des blessures physiques lors de l'installation.
PAGE 9
voulu.
PAGE 10
1. de 10''. Construisez des supports de structure sur le cadre 2. au comptoir. Vigo recommande de laisser un rebord de 1/4'' sur suffisamment d'espace pour les robinets et les jets d'eau, utilisez 3. 4.
PAGE 11
Entretien TOUJOURS et essuyez-le bien. vinaigre et d'eau, puis rincez minutieusement avec de l'eau. JAMAIS en acier inoxydable.
PAGE 12
VIGO INDUSTRIES, LLC ("VIGO") utilisateur final en vue d'un usage personnel domestique. D'autres limitations s'appliquent en cas d'usage commercial. constructeur. tiers. Limitations directement ou indirectement. blessures, voire la mort. constructeur. Limitations commerciales Service de garantie proposition par le client met fin aux obligations de VIGO au titre de la garantie.
PAGE 13
ESPECIFICACIONES DEL LAVABO Modelo VGRA3018SL MODELO DESTACADO VGRA3018SL Esquinas de radio de 10 mm Reversible para plano delantal delantero o delantero ranurado delantal CONTENIDOS DEL PAQUETE Fregadero Colador DIMENSIONES NOMINALES MODELO NRO. VGRA3018SL PROFUNDIDAD DEL FREGADERO DE TAZON 28 1/2" x 16 1/2" EXTERIOR DIM. 30" x 18" 9 5/8" 30" [761mm] NOTA: Debido a la naturaleza del material, los modelos pueden diferir hasta 5 mm de la dimensiones.
PAGE 14
Recomendaciones generales: coloquen instaladores profesionales y con experiencia. Para realizar cortes e instalaciones especiales aspecto. distribuidor de armarios. Herramientas y Materiales necesarios: Alcohol Desnaturalizado Abrazaderas para madera Sellador adhesivo de silicona Trapos para protegerse.
PAGE 15
del fregadero Figura 1 Figura 2 Figura 3 como para el movimiento completo de la boca del grifo y sus llaves. desde el extremo delantero de la encimera Figura 4 Figura 5 encimera.
PAGE 16
1. especial con un corte delantero para fregaderos de 10" de profundidad. Construya apoyos estructurales en el bastidor interior del armario de la base del fregadero. Los apoyos estructurales deben sostener el peso del fregadero y todos sus el embutido de su parte superior contra el fondo de la encimera 2. Plantilla y corte instalaciones embutidas, corte la encimera a lo largo del exterior delantero sobresalga 3/4" del extremo delantero de la encimera. hacer el corte real. 3.
PAGE 17
Cuidado y Mantenimiento SIEMPRE mayor limpieza preventiva. minerales que pueden afectar su aspecto. NUNCA pues puede arruinar el acabado. demasiado largo pues pueden arruinar el acabado. fregadero.
PAGE 18
VIGO INDUSTRIES, LLC ("VIGO") la fecha de compra inicial por parte del propietario/ usuario final, contratista o constructor a VIGO o a un distribuidor autorizado de VIGO y durante toda la vida del propietario o usuario final originales. otras personas. Limitaciones indirecta. propietario/usuario final.