Installation ® Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-845-4641 or visit the Viking Website at vikingrange.
Table of Contents IMPORTANT–Read and Follow! Warnings & Important Safety Instructions_____________________________________________________ 3 • Before beginning, please read these instructions completely and carefully. Your safety and the safety of others is very important. • DO NOT remove permanently affixed labels, warnings, or plates from product. This may void the warranty. We have provided many important safety messages in this manual and on your appliance.
IMPORTANT–Read and Follow! A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local laws, or local ordinances. • The required use of a GFI is normally related to the location of a receptacle with respect to any significant sources of water or moisture. • Viking Range, LLC will NOT warranty any problems resulting from GFI outlets which are not installed properly or do not meet the requirements below.
Dimensions Specifications Dual Fuel 30” W. Range Dual Fuel 30” W. Range Description 29 (75-7/8 .9 ” cm ) 3 (91 5-7 .1 /8” cm ) to min . (94 37 .0 ” cm )m ax . RVDR Overall width 29-7/8” (75.9 cm) Overall height To top of side trim – 35-7/8” (91.1 cm) min. 37” (94.0 cm) max. Legs adjust – 1-1/8” (2.9 cm) Overall depth from rear To front of side panel – 25” (63.5 cm) To front of door – 25-3/4” (65.4 cm) To front of control panel – 27 1/8" (68.9 cm) To end of knobs – 29" (73.
Clearance Dimensions • Wall cabinets above the range must be a minimum of 42” (106.7 cm) above the range cooking surface for the full width of the range. This minimum height requirement does not apply if a range hood is installed over the cooking surface. • This range may be installed directly adjacent to existing 36” (91.4 cm) high base cabinets. IMPORTANT: The side trim MUST be 3/8” (.95 cm) above the adjacent base cabinet countertop.
Electrical & Gas Requirements Electrical & Gas Requirements Electrical Requirements Flexible Connections: In Canada: CAN 1-6, 10-88 metal If the unit is to be installed with flexible couplings and/or quick-disconnect fittings, the installer must use a heavy-duty AGA design-certified flexible connector of at least 1/2” (1.3 cm) ID NPT (with suitable strain reliefs) in compliance with ANSI Z21.41 and Z21.69. connectors for gas appliances and CAN 1-6.9 M79 quick disconnect devices for use with gas fuel.
General Information Installation NOTICE READ AND FOLLOW ALL WARNING AND CAUTION INFORMATION WHEN INSTALLING THIS APPLIANCE. Moving, Handling, and Unpacking • All openings in the wall behind the appliance and in the floor under the appliance must be sealed. • DO NOT obstruct the flow of combustion and ventilation air. Remove and discard all packing materials, including cardboard and tape on the outside and inside of the range. DO NOT use the handle or oven door to lift the oven.
Leg Installation Electrical Connection (3-wire) Note: If you have a 4-wire connection, see following section for 4-wire connection instructions. 2 1 WARNING WARNING ELECTRICAL SHOCK HAZARD ELECTRICAL SHOCK HAZARD 1 1 3 2 Legs are packed in the cardboard top pack. Note: Legs should be installed near to where appliance is to be used, as they are not secure for long transit. Note: It is strongly recommended that a pallet or lift jack be used rather than tilting. Raise unit about a foot.
Electrical Connection (3-wire) (cont.) Bare Wire Connection Eyelet Connection Electrical Connection (4-wire) 4 WARNING 2 1 Attach line #1 (red) and line #2 (black) leads to outside terminal. Attach neutral wire (white) to center terminal on the terminal block. To make a bare wire connection, use holes on the left side of the terminal block. To connect eyelet style wires, use holes on right side of terminal.
Electrical Connection (4-wire) (cont.) Bare Wire Connection Eyelet Connection Leveling/Adjustments/Alignment 2 1 4 1 1 Measure the four corners in cutout area to verify if flooring is level. Feed supply cord up through hole in bottom of range back. To make a bare wire connection, use holes on the left side of the terminal block. To connect eyelet style wires, use holes on right side of terminal.
Wall Mount Anti-tip Installation (cont.) Leveling/Adjustments/Alignments (cont.) 7 2 3 3-5 (9. /8” 2c m) ) ) (A .3 cm 1 ( /2” +1 Set the high corner of range so that the top of side trim is 3/8” (0.95 cm) above countertop. Level range to high corner. Locate anti-tip bracket on rear wall with the top left corner at measurement (A) plus 1/2” (1.3 cm) from the floor and 3-5/8” (9.2 cm) from where the right side of range (facing range) is to be located.
Final Installation Floor Mount Anti-tip Installation (cont.) 3 1 4 2 1 x2 1 2 2 Remove two screws from back of range. Attach bracket to back of range using two screws. Slide range into place. Be sure anti-tip bracket slides into the anti-tip opening. Burner heads and burner caps are packed in the cardboard top pack with the grates. Align burner head on burner base. Place burner cap on burner head. Place grate onto the burner pan.
Door Replacement and Adjustment Final Preparation 2 1 • All stainless steel body parts should be wiped with hot, soapy water and with a liquid cleaner designed for this material. If buildup occurs, DO NOT use steel wool, abrasive cloths, cleansers, or powders! If it is necessary to scrape stainless steel 2 1 2 to remove encrusted materials, soak with hot, wet cloths to loosen the material, then use a wool or nylon scraper.
Service & Registration Only authorized replacement parts may be used in performing service on the appliance. All servicing should be referred to a qualified technician. Contact Viking Range, LLC, 1-888-845-4641, for the nearest service parts distributor in your area or write to: VIKING RANGE, LLC PREFERRED SERVICE 111 Front Street Greenwood, Mississippi 38930 USA The serial number and model number for your range can be found by opening the door and looking under the control panel.
