Installation GUIDE Range / Rangetop Rear Island Trim / Backguard / High Shelf Accessories Range Curb Base Fronts
Rear Trim Accessories MODELS BACKGUARD HIGH SHELF CURB BASE VGIC5301 VGCC530 C/VDSC530 C/VESC530 C/VISC530 VGRT530 C/VER530 C/VIR530 P30BG8SS B304H24SS P30CBF4SS VGCC536 C/VDSC536 VGIC5361 VGRT536 P36BG8SS VGCC548 C/VDSC548 VGRT548 P48BG8SS VGCC560 C/VDSC560 P60BG8SS B60HS24SS P60CBF4SS VGR530 C/VDR530 VGIC5302 VRT530 BG8530SS HS24530SS P30CBF4SS VGR536 C/VDR536 VGIC5362 VRT536 BG8536SS HS24536SS P36CBF4SS VGR548 C/VDR548 VRT546 BG8548SS HS24548SS P48CBF4SS VGR560 C/VDR560 BG85
Rear Trim Accessories All rear trim devices are installed in the same basic way. ATTACHING REAR TRIM (Illustration I) Grasp the trim on each end and carefully place in the channels (B) located at each rear corner of the product. Align the screw holes (A) at each end of the trim device with the holes (A) in each rear channel of the product. Secure with the 4 enclosed screws.
Rear Trim Accessories ATTACHING BACKGUARD (Illustration 3) Backguards come equipped with Nylon Spacers (See Figure 1), which are needed to space the range off a combustible wall a prescribed safe distance. Figure 1 These spacers can also be removed if used with any of the models* listed below: • C/VGCC530 *If you have one of these models, the spacers are not • C/VDSC530 required, even if with a combustible wall.
Rear Trim Accessories ATTACHING ISLAND TRIM (Illustration 4) A IMPORTANT: USE OF ISLAND TRIM WITH AND WITHOUT 6” (15.2 CM) CLEARANCE. Normal installation for island trim on either a range or rangetop is in an island/peninsula or where there is a minimum clearance of 6”(15.2 cm) to any type of wall at the rear of the unit. Ranges and rangetops with an island trim installation can be installed at zero clearance to the rear wall as long as the wall is non-combustible.
CURB BASES STANDARD CURB BASE FRONT 1. The standard curb base front (A) is completely assembled. 2. Remove the assembly from the carton and simply clip onto the front range legs. 3. The assembly is adjustable about 2” (5.1 cm) front to back so that alignment with the cabinet toe front is possible. Loosen brackets on each side, but allow snug fit. Clip assembly onto range legs; determine front to back setting; remove, tighten bolts, and reattach.
CURB BASES CUSTOM CURB BASE FRONT 1. Remove the standard curb base front assembly from the carton. 2. Remove the front (A) from the mounting assembly (B). 3. Attach locally supplied front (C) to the mounting assembly (B) ad simply clip onto the front range legs. Important Note: The locally supplied front must not be any taller than 3-1/8” (7.9 cm) tall. Fronts taller than 3-1/8” (7.9 cm) could obstruct the airflow. 4. The assembly is adjustable about 2” (5.
Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For additional product information, call 1-888-845-4641 or visit our website at vikingrange.
