Installation guide

ManualsBrandsViking ManualsConvection OvenBuilt-In Convection Microwave Hood

Mounting Space

This Convection Microwave Hood requires a mounting

space on a wall as shown in ﬁgure 1. It is designed to

be used with standard 12-inch wall cabinets.

For proper installation and servicing, a 2-inch space is

necessary between the top of the range backguard and

the bottom of the Convection Microwave Hood.

Wall Construction

This Convection Microwave Hood should be mounted

against and supported by a ﬂat vertical wall. The wall

must be ﬂat for proper installation. If the wall is not ﬂat,

use spacers to ﬁll in the gaps. Wall construction should

be a minimum of 2" x 4" wood studding and 3/8" or more

thick dry wall or plaster/lath. The mounting surfaces must

be capable of supporting a weight of 110 pounds—the

oven and contents—AND the weight of all items which

would normally be stored in the top cabinet above the

unit.

The unit should be attached to a minimum of one 2" x

4" wall stud or two 2" x 3" wall studs.

To ﬁnd the location of the studs, one of the following

methods may be used:

Use a stud ﬁnder, a magnetic device which locates the •

nails in the stud.

Use a hammer to tap lightly across the mounting •

surface to ﬁnd a solid sound. This will indicate stud

location.

The center of the stud can be located by probing the

wall with a small nail to ﬁnd the edges of the stud and

then placing a mark halfway between the edges. The

center of any adjacent studs will normally be 16" or 24"

to either side of this mark.

Viking Installation Guide

Convection Microwave Hood

111 Front Street

Greenwood, Mississippi 38930 USA

IMPORTANT–Please Read and Follow!

Please read all instructions thoroughly before installing the Convection Microwave Hood. Two people are •

recommended to install this product.

If a new electrical outlet is required, its installation should be completed by a qualiﬁed electrician before the •

Convection Microwave Hood is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on page 2.

Backguard

At least 2"

15.5"

30"

12"

30" or more

from cooking

surface

66" or more

from ﬂoor

Summary of content (8 pages)

PAGE 1
Viking Installation Guide IMPORTANT–Please Read and Follow! • Please read all instructions thoroughly before installing the Convection Microwave Hood. Two people are recommended to install this product. • If a new electrical outlet is required, its installation should be completed by a qualified electrician before the Convection Microwave Hood is installed. See 3 ELECTRICAL GROUNDING INSTRUCTIONS on page 2.
PAGE 2
Electrical Grounding Instructions Hood Exhaust Duct This appliance must be grounded. This oven is equipped with a cord having a grounding wire with a grounding plug. It must be plugged into a wall receptacle that is properly installed and grounded in accordance with the National Electrical Code and local codes and ordinances. In the event of an electrical short circuit, grounding reduces risk of electric shock by providing an escape wire for the electric current.
PAGE 3
Tools Recommended for Installation • Saw to cut exhaust opening (if needed) • Electric Drill • Protective Drop Cloth for product and range you may also use carton for protection figure • Phillips Screwdriver • ½", ⁵⁄₈" and ³⁄₃₂" Drill Bits • 1½" Wood Bit or Metal Hole Cutter (if metal cabinet is used) • Scissors • Measure • Pencil • Tape Installation Hardware Parts Included The INSTALLATION HARDWARE (items 1 - 7) packed with the oven should contain the following: Hardware Kit #5450M023-
PAGE 4
Ventilation System (Preparing Oven for Installation) figure figure This Convection Microwave Hood is designed for adaptation to three types of hood ventilation systems. Select the type required for your installation. Recirculating — non-vented, ductless. Follow installation procedure (A). Recirculating requires the use of the Charcoal Filter, which has been installed in the oven. Hood Fan Unit Horizontal Exhaust — outside ventilation. Follow installation procedure (B).
PAGE 5
figure Exhaust Damper Assembly figure figure figure figure figure HORIZONTAL EXHAUST: Replace the fan cover bracket. Make sure the fan blades are visible through the rear openings in the oven before proceeding. Attach fan cover bracket to unit with 4 screws. The hood fan unit is now rotated for horizontal exhaust operation. (A) Rotate 90˚ figure figure • Remove and save 4 screws and fan cover bracket as shown in figure 5. Withdraw hood fan unit. See figure 6.
PAGE 6
Mounting Plate • Separate 4 Toggle Bolts, packed in the INSTALLATION HARDWARE, from the Toggle Nuts. figure figure figure Before insertion, be sure you leave a space more than the thickness of the wall between the Mounting Plate and the end of each of the Toggle Nuts (in the closed position). If you do not leave enough space, the Toggle Nut will not be able to open on the other side of the wall.
PAGE 7
Oven Installation (B) MOUNTING OVEN TO THE WALL: Hang the (B)oven on the lower edge of the mounting plate. Take care that the power cord is able to clear the edge of the hole as the oven is rotated upward. (In the case of a non-recessed bottom in the top cabinet, the hole for the cord may need to be enlarged.) Remove the carton portions. figure figure figure MOUNTING OVEN TO THE WALL: Using cutting line around the carton, cut into two pieces (A) and (B).
PAGE 8
(B) figure figure figure figure Oven Installation (C) (D) Deflector MOUNTING DEFLECTOR: Secure the deflector with 3 Tapping Screws 4 x 12mm, packed in the Installation Hardware. figure MOUNTING OVEN TO THE WALL: Install Grease Filters by fitting into the opening. Push back and up into place. (C) Checklist for Installation (D) • Make sure the unit has been installed according to all of the Installation Instructions and the Wall and Top Cabinet Templates.