INSTALLATION Manual Type 115 INSTRUCTIONS Viking W-1000, C-1000B with Essex 265 controller For Models 101-VIK 103-VIK 107-VIK 201-VIK 203-VIK 301-VIK 302-VIK 304-E265-VIK 305-E265-VIK 400-E265-VIK 401-E265-VIK Specifications Communication Access Control Viking W-1000 Doorbox uses “half-duplex” communication, allowing for high speaker and microphone volume, witout the possibility of feedback Essex “stand-alone” 5 button keypad 1 relay 5-6 users 16.5 VAC power supply included 501 E. Goetz Ave.
Viking W-1000 Wiring Wiring 2 Doorboxes into Unused CO Port on KSU DOOR STRIKE 2 DOOR STRIKE 1 DOOR BOX 2 DOOR BOX POWER DOOR BOX 1 When used w/o CO line KSU, “Talk Battery” is ON ON 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1 C O M DO NOT CONNECT CO LINE IN KEYLESS CONTACT LINE OUT TO PHONES EARTH GND PHONE LINE INPUT 13.5 VAC IN VIKING Model C-1000B N. N. O. C. 1 2 3 TALK OFF OFF BATT ON AUX OUTPUT N.C. AUX OUTPUT N.O.
Viking W-1000 Wiring Wiring Using Standard Phones - Doorboxes Share CO Line with Phones DOOR STRIKE 2 DOOR STRIKE 1 DOOR BOX 2 DOOR BOX POWER DOOR BOX 1 When used with standard phones “Talk Battery” is OFF ON 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1 C O M CO LINE IN KEYLESS CONTACT LINE OUT TO PHONES EARTH GND PHONE LINE INPUT 13.5 VAC IN VIKING Model C-1000B N. N. O. C. 1 2 3 TALK OFF OFF BATT ON AUX OUTPUT N.C. AUX OUTPUT N.O.
Viking W-1000 Wiring Wiring into Unused CO Port on KSU - with Essex Gate Control System AC Out For Strike DOOR STRIKE 2 DOOR STRIKE 1 DOOR BOX 2 DOOR BOX POWER DOOR BOX 1 KEYLESS CONTACT LINE OUT TO PHONES EARTH GND PHONE LINE INPUT 13.5 VAC IN VIKING Model C-1000B When used w/o CO line “Talk Battery” is ON ON 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1 C O M N. N. O. C.
Viking W-1000 Wiring Wiring Using Standard Phones - with Essex Gate Control System Contact Closure for Gate Operation DOOR STRIKE 2 DOOR STRIKE 1 DOOR BOX 2 When used with standard phones, “Talk Battery” is OFF ON 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 1 1 2 3 TALK OFF “Open” Terminals on Gate Motor CO LINE IN TO STANDARD PHONES NC 2 NO 2 COM 2 NC 1 NO 1 COM 1 Essex Model 265 DC OUT 13.8 VAC 1.25A OFF BAT ON AC IN Earth Keypad Cable N. N. O. C.
Doorphone Adjustments and Programming Microphone Volume In certain noisy locations (traffic or wind), the microphone volume may need to be decreased. A symptom of this is one-way talk path, in which the distant party cannot be heard over the speaker. A “MIC VOL” adjustment is provided on the doorphone for increasing or decreasing the microphone volume. Speaker Volume The “SPKR VOL” pot can be adjusted to increase or decrease the speaker volume to the desired level.
C-1000B Door Controller Programming Program Auxilliary Contacts* Step Action 1 Make sure C-1000B is in Programmin Mode - See Page 8 2 Program Aux Contact activation time as follows: 3 Enter time (seconds) follwed by #03 EXAMPLE: 01#03 programs Aux Contact for 1 seoncd. NOTE: Entering a time “00” sets time = 1/2 second *In this mode, Auxiliary contacts can be activated (closed) whenever Doorbox 1 or Doorbox 2 is activated.
Viking Operation OPERATION ANSWER A CALL FROM DOORBOX When the phones ring, pick up a phone to be connected to the visitor. When the C-1000B controller is used, you will hear a beep tone when the phone is answered - one beep for doorbox 1, and 2 beeps for doorbox 2. PLACING CO LINE CALLS ON HOLD (CALL WAITING) If a phone call is in progress, and a door box is activated, a single or double “call waiting “ tone will be heard. To place the call in progress on hold and speak to the visitor, push #.
Set Essex Relay Options GOAL: To use jumper pins on circuit board to configure standard relay options. In this configuation, Codes 1 and 2 operate Relay 1. Codes 3, 4, 5 operate Relay 2. Step 1 Code Action Relay 1 and 2 activate.
Programming of Essex Keypad GOAL: Set-up master and user codes Set Master Code Step Action 1 Press “Program” switch once. (keypad will beep 4 times) 2 Once “Program” switch is pressed, you have 2 minutes to complete Step 5. 3 Press “1119”. (you will hear 3 beeps) 4 Step 5 must be completed within 5 seconds of Step 3. 5 Enter “Master Code” * 6 Wait 5 seconds for 3 beeps to confirm new “Master Code”. Set User Code 1 Step Action 1 Enter “Master Code” 2 Enter 111 (3 beeps).
Programming of Essex Keypad Set User Code 4 Step Action 1 Enter “Master Code”. 2 Enter 117 (3 beeps). 3 Enter User Code 4. 4 Wait 5 seconds for 3 reset beeps. Set User Code 5 Step Action 1 Enter “Master Code”. 2 Enter 119 (3 beeps). 3 Enter User Code 5. 4 Wait 5 seconds for 3 reset beeps. Delete Any Code Step Action 1 Enter Master Code . 2 Enter address of code to be deleted (111, 113, etc.). 3 Do not enter any code until you hear 3 reset beeps.
Programming of Essex Keypad Set Activation Time Of Relay 1 (User codes 1 & 2 - see note below) Step Action 1 Press “Program” switch (keypad will beep 4 times). 2 Enter 1117 (3 beeps). 3 Enter 1 for every 1 second latch time, and 5 for every 5 seconds. Examples: 6 seconds = 5, 1 8 seconds = 5, 1, 1, 1 12 seconds = 5, 5, 1, 1 4 Wait 5 seconds for 4 reset beeps. Set Activation Time Of Relay 2 (User codes 3, 4& 5 - see note below) Step Action 1 Press “Program” switch (keypad will beep 4 times).