Viking Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site at vikingrange.
IMPORTANT–Please Read and Follow! Table of Contents Warnings & Important Information ______________________________________ 3 Dimensions & Cutout Dimensions ______________________________________ 4 Specifications ________________________________________________________ 5 Custom Door Panel Specifications ______________________________________ 6 Custom Door Panel Installation Option _________________________________ 7 General Information __________________________________________________ 8 Site Preparation _
Specifications Dimensions & Cutout Dimensions Professional Series 26-3/8” (67.0 cm) 23-1/8” (59.0 cm) 26-3/8” (67.0 cm) 23-3/4” (60.3 cm) 2 3-7/ (60.6 c8” m) Built-In Dishwasher Description Overall width Overall height from floor 2-5/8” (6.7 cm) 3-3/16” (8.1 cm) Overall depth from rear–Professional Overall depth from rear–Designer 33-7/ (86.
Custom Door Panel (Specifications) (Installation Option) 11-17/32" (29.3 cm) 5-7/8" (14.9 cm) 5/8" (1.6 cm) 5/8" (1.6 cm) 5/8" (1.6 cm) Have the overlay panel constructed per dimensions. The panel thickness MAY NOT exceed 5/8” (1.6 cm) for flush installation in most cabinets. Ensure that the design, construction, and installation of the panel overlay and its handle mounting is sufficient to reliably operate in this application with a maximum panel weight of 18 lbs. (8.2 kg.
General Information General Information • Read these instructions carefully and completely before installing the dishwasher. The installation should be carried out by a qualified installer, who is familiar with all local codes and ordinances for electrical and plumbing connections. If the dishwasher is being installed for the first time, most of the work has to be done before you move it into place. If you are replacing an old dishwasher, you must check the old connections.
Hardwire Conduit Option a b Trim Installation Options To install dishwasher without trim, remove the 6 screws and washers (3 per side) and remove trim. To attach wiper gasket to dishwasher, pull protective film off adhesive back on wiper gaskets and apply to leading edge of dishwasher frame. 1a 1 Remove any loose items in the dishwasher and carefully lay the dishwasher on its back. NOTE: Be careful not to pinch hoses or power cord beneath dishwasher. Remove bottom pan and front plate.
Trim Installation Options (cont’d.) Dishwasher will ship with trim installed for panel flush install. If needed, attach wiper gasket by pulling protective film off adhesive back on wiper gasket and apply behind hemmed edge of side trim. Trim Installation Options (cont’d.) To install dishwasher cabinet flush with trim, remove the 6 screws and washers (3 per side) holding side trim on. Shift the side trim forward. Use rear hole on side trim and the same hole on dishwasher to reattach trim.
Counter Balance Spring Adjustment - If Necessary a b Installation Procedure 2 1 1 Increase tension 2 Decrease tension 1 Disconnect cable from hook. Set counter balance spring connector in appropriate location. c NOTE: For custom panel installation the door may require adjustment to the preload of the counterbalance springs. Follow these steps to adjust the tension. Carefully lay dishwasher on its back and attach the kick plate brackets. Screws for the brackets will already be in the base.
Installation Procedure (cont’d.) Installation Procedure (cont’d.) 8 7 11A Air Gap 11B Air Gap Minimum 20” (50.8 cm) from floor Attach screws through trim pieces into cabinets. (Discharge with air gap) Install High Loop Clip, which is provided, a minimum of 20” (50.8 cm) from the floor. 9 (Discharge with food waste disposer and air gap) 12 10A 13 1.0” (2.5 cm) Cut here for 5/8” (1.6 cm) Cut here for 3/4” (1.9 cm) Connect water line. Plug LED light into dishwasher and install kick plate.
Performance Checklist Testing for Leaks Final Preparation • Remove packaging and parts. • Some stainless steel parts may have a plastic protective wrap which must be peeled off. • Turn on the water supply and check for leaks. Unit Reset • Turn the power on at breaker/fuse box and test the dishwasher operation by running a rinse and hold cycle. (This should take about 12 minutes.) • If the unit should need to be reset for any reason, push and hold the “START” button for 4 seconds.