Specifications
0.781
dia.
7.22
5.36
8-32 x .5" set
screws provided
1.70
3.40
1.70
3.40
5.00
6.78
1.69
0.80
3.30
1.55
CALL
CONNECTED
EMERGENCY
PHONE
MODEL E-1600-03B
VIKING ©
PUSH FOR
VIKING©
HELP
2.605
0.795
E
E
-
-
1
1
6
6
0
0
0
0
-
-
5
5
0
0
A
A
/
/
5
5
2
2
A
A
(
(
o
o
p
p
t
t
i
i
o
o
n
n
a
a
l
l
E
E
W
W
P
P
a
a
v
v
a
a
i
i
l
l
a
a
b
b
l
l
e
e
)
)
0.827
(4) 0.335 x 0.177
mounting slots
for #4 or #6 studs
Red
Green
-or-
0.17
RedBlack
Black
Black
Red
Red
2.60
2.10
2.60
2.10
3.54
3.20
2.95
0.80
Maximum
2.0
0.95
2.20
2.40
Speaker
(included)
Screen (included)
Speaker Gasket
(EWP only)
(2) 0.156 diameter
mounting holes
Gel-filled butt
connectors
2.37
Cone
Dia.
.785.47
.50
1.0
(2) 0.10 diameter
mounting holes
Mic Hole
Clear Spacer Red Retaining
Lens LED Ring
EWP version
is connected and
encapsulated
Panel
Ring
Terminal
(included)
* Earth Ground
(optional)
Red (LED anode)
Black (LED cathode)
PUSH FOR
VIKING©
HELP
Connect to "INFO" button
(E-1600-52A only, requires a
0.75" diameter mounting hole)
Connect to "PUSH FOR HELP"
or "HELP" button (requires a
0.75" diameter mounting hole)
Red call connected LED with mounting
hardware (requires a 0.250" diameter
mounting hole). Note: If you do not want
to use the LED, tuck it inside the unit.
Do NOT cut it off.
Connect to
phone line
Note: When using the included
push button switches, cut off the
forked portion of the spade lugs
and fasten screws to the barrel
portion of the spade lugs.
BL-1 grade 2 black
Braille label included
Drip Loop
Mylar Speaker Dimensions
Standard Mic Mounting Boot. Glue or
screw directly behind 0.04” - 0.125” diam-
eter hole in panel.
Note: Mic holes should be near the bot-
tom of the boot to allow for drainage.
PC Board Mounting
Side View
Optional Enhanced Weather Protection (EWP): The optional EWP products
feature sealed trim pots, sealed DIP switches, hand soldered and silicon
sealed connections, rubber boots and gaskets, urethane potted circuit boards
and gel-filled butt connectors.
Note: This is a 1600A parts kit without chassis.
Shipping Weight: .45 kg (1 lb)
Connections: Gel-filled butt connectors
EWP Mic Mounting Boot. Glue to the
back of your panel at an upward angle
(shown left) behind a 0.10” - 0.25” diame-
ter hole.
Side
View
Important: If installing the EWP version outdoors, apply a non-corrosive silicone to back side of LED and push button switches
after making all connections and testing. Completely encapsulate exposed switch connections (screw terminals/stripped wires)
and bare wire connections.
Dimensions: 183mm x 149mm x 39mm (7.22” x 5.36” x 1.55”)
Material: .074” (14 gauge) Brushed stainless steel panel and extra heavy duty button with LED
Shipping Weight: 1.36 kg (3 lbs.)
Connections: Gel-filled butt connectors
Mounting: Surface mount to walls, posts, single gang boxes, double gang boxes or 4” x 4” electrical junction boxes or recess mount in
elevator phone boxes.
Optional Enhanced Weather Protection (EWP): The optional EWP products feature sealed trim pots, sealed DIP switches, hand sol-
dered and silicon sealed connections, rubber boots and gaskets, urethane potted circuit boards and gel- filled butt connectors.
Note: For greater weather resistance, apply a bead of clear silicon caulking around the top edge and sides of the chassis
E
E
-
-
1
1
6
6
0
0
0
0
-
-
0
0
3
3
B
B
(
(
o
o
p
p
t
t
i
i
o
o
n
n
a
a
l
l
E
E
W
W
P
P
a
a
v
v
a
a
i
i
l
l
a
a
b
b
l
l
e
e
)
)
Bottom View
Back View
Front View
(4) .22 diameter
mounting holes
(2) .187 x .50
slots for single
gang box
Grade 2
Braille Label
Push To Call Button
Condensation
Drain Hole
Call Connected LED
(4) .187 x .50
slots for double
gang box
5