Programming instructions

ManualsBrandsViking ManualsHome Safety ProductEmergency Phones

G.A.L. HANDS FREE EMERGENCY

TELEPHONE

MODEL GAL-6400

I. GENERAL

The GAL-

6400 Hands Free Emergency Telephone permits a

pre-programmed number to be dialed when the

"push to call"

button is depressed on the station. The emergency personnel

upon receiving the call can hear a 10 second recorded message.

By pressing the star "*" key on their telephone keypad, the

emergency phone will respond by stopping the recorded mess

age

and/or issuing a pre-

programmed tone location I.D. number and

illuminate the "CALL RECEIVED" indication. The “CALL

RECEIVED” indicator will also light automatically after playing

the recorded message a programmed number of times. During the

call the unit will act as a standard speaker-

phone. At any time

after the star key is pressed, the pound ”#” key can be used to

hang up the emergency phone.

The unit also has the capability of dialing up to four additional

pre-programmed numbers if the first number

called is

unanswered and/or busy.

II. QUICK PROGRAMMING INSTRUCTIONS

To program a single emergency number to be dialed and voice

location announcement to be recorded without changes to the

security code or tone location ID.

A. Connect the phone line to t

he modular connector supplied on

the GAL-6400.

B. From another phone, dial the phone number for the line that

the GAL-6400 is attached to. The GAL-6400 will answer

immediately.

C. Dial the factory set security code 1,2,3,4,5,6 on the telephon

keypad. Two beeps should be heard.

. Using the telephone keypad, enter the emergency number the

GAL-6400

should dial followed by #,0,0. Two beeps should

be heard.

Summary of content (10 pages)

PAGE 1
G.A.L. HANDS FREE EMERGENCY TELEPHONE MODEL GAL-6400 I. GENERAL The GAL-6400 Hands Free Emergency Telephone permits a pre-programmed number to be dialed when the "push to call" button is depressed on the station. The emergency personnel upon receiving the call can hear a 10 second recorded message. By pressing the star "*" key on their telephone keypad, the emergency phone will respond by stopping the recorded message and/or issuing a pre-programmed tone location I.D.
PAGE 2
E. To record a 10 second voice location message, dial “* 4” and speak after the tone. To stop the recording, press any telephone keypad key, or wait 10 seconds for the recording to stop. We recommend adding the statement, “hit star key to end message” at the end of your recording. F. Hang up. Programming is now complete. Test the GAL-6400 for proper operation.
PAGE 3
This switch determines whether or not the push button can cancel (hang up) a call after it has been initiated. It is recommended that the call CAN be cancelled (switch ON). This allows for "resetting" the phone line should the line become "stuck". If you wish to change, do so after programming.
PAGE 4
C. Initially test the unit by pushing the "PUSH TO CALL" button. A dial tone followed by touch tones should be heard. Push the button a second time to cancel the call. If a dial tone was not heard, check the connection of the phone line to the unit. Since all programming will be done by dialing this unit from another telephone, you may now mount the phone unit, and/or close and secure the station. D.
PAGE 5
Note: This example would be used on telephone systems that require pressing "9" to get an outside line. The "*,7" provides a four second pause to allow for the outside line dial tone. - Store the pulse dialed emergency number: "562-1275" enter: *,6,5,6,2,1,2,7,5,#,0,0 Note: This example would be used on telephone systems that require pulse dialing (tone dialing does not work).
PAGE 6
E. The GAL-6400 has a built in digital recorder/announcer that can be used to give location identification. Both the emergency personnel and the elevator car occupants will hear the message, however the car occupants will hear it at a reduced volume. It provides 10 seconds of record time and has two options for operation. Forced Play Time By factory default, the 10 seconds message is played automatically when the unit detects that the call has been answered (forced play time value set to “00”).
PAGE 7
2. At the end of recording, play back of the message is automatic. To repeat play back for your review enter *5. To re-record, enter *4. 3. To erase and disable the voice message feature, enter *3. Example announcement: - “Emergency call from elevator 3 at 125 Broadway. Press the star key to stop this announcement.
PAGE 8
feature (second number will not be dialed). The factory default is 1 (feature disabled). Redial on busy - This will enable or disable the feature to dial the second emergency number on a busy signal. A value of 1 disables this feature, a value of 2 enables it. The factory default is 1 (feature disabled). Pulse dialing rate - This is the rate at which the phone will dial in pulse mode. A value of 1 sets phone to 10 pulses per second (PPS), a value of 2 sets it to 20 PPS. The factory default is 1.
PAGE 9
- Store time functions & set redial feature: 0.4 seconds Talk/Listen 6 minutes Max. Call Time 50 seconds Silence Time 6 ring Redial Ring Count Redial on Busy 10 pps pulse dialing rate enter: 4,6,5,6,2,1,#,1,8 IV. TESTING THE PHONE UNIT Test the unit in the elevator by depressing the "push to call" button on the cover of the station. A dial tone should be heard followed by the dialing of the emergency number.
PAGE 10
B. Programming problems 1. GAL-6400 does not accept programming. Two beep response from unit is not heard when programming. The GAL-6400 is looking for standard touch tones for programming. If you are not successful with the phone you are using, try calling from outside the building such as from your office or home phone. 2. Cannot program multiple phones sharing a single phone line. Since only one GAL-6400 phone can pick up at a time, you must program each of the units one at a time.