Installation Custom Panel All Refrigerator / All Freezer FDRB5303 / FDRB5363 / CFDRB5303 / CFDRB5363 FDFB5303 / FDFB5363 /CFDFB5303 / CFDCFB5363
Table of Contents Warnings & Important Information ____________________________________________________________________3 All Refrigerator/Freezer Dimensions & Specifications (30” and 36”) ____________________________________________________6 Cutout Dimensions (30”) ____________________________________________________________________8 Anti-Tip Dimensions (30”) ___________________________________________________________________9 Cutout Dimensions (36”) _________________________________________________________
IMPORTANT – Please Read and Follow • Make sure that incoming voltage is the same as unit rating. An electric rating plate specifying voltage, frequency, wattage, amperage, and phase is attached to the product. • To reduce the risk of fire, electrical shock, or injury to persons, installation work and electrical wiring must be done by a qualified technician in accordance with all applicable codes and standards, including fire-rated construction.
IMPORTANT – Please Read and Follow! A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local laws, or local ordinances. • The required use of a GFI is normally related to the location of a receptacle with respect to any significant sources of water or moisture. • Viking Range, LLC will NOT warranty any problems resulting from GFI outlets which are not installed properly or do not meet the requirements below.
WARNING WARNING ELECTRICAL SHOCK HAZARD TIP OVER HAZARD Appliance is top heavy and tips easily when not completely installed. Keep doors closed until appliance is completely installed and secured per installation instructions. Disconnect power or turn power disconnect switch to OFF position before removing top grille. Failure to do so can result in death or electric shock. Use two or more people to move and install appliance. Failure to do so can result in death or serious injury.
Dimensions 30” All Refrigerator/Freezer 29” 30” (73.7 c m) (76.2 cm ) 3–19/ 3 (9.1 cm2” ) 36” All Refrigerator/Freezer 9–5/3 2 (23.3 c ” m) 35” 36” 3–19/ (88.9 c m) (91.5 c m) 3 (9.1 cm2” )) 9–5/3 (23.3 c2” m) 82–3 75–1 (210. /4” 2 cm min. ) to ies varare) t n e rdw (192 5/16” .9 cm ) 84–1 / (213. 16” 5 cm max. ) rem d ha asu plie Meally su p (loc 82–3 75–1 (192 5/16” .9 cm) (210. /4” 2 cm min. ) to ies varare) t en w 84–1 d r rem d ha asusupplie e M y / (213.
Specifications 30” All Refrigerator/Freezer Description Overall width Overall height (from bottom) Overall depth (from rear) Cutout width Cutout height Cutout depth Electrical requirements Maximum amp usage Inlet water requirements Overall interior dimensions total capacity Maximum panel weight FDFB/CFDFB FDRB/CFDRB 30” (76.2 cm) 82-3/4” (210.2 cm) min. to 84-1/16” (213.5 cm) max. To front edge of side trim: 23-3/16” (58.9 cm) To front edge of door trim: 24” (61.0 cm) 30” (76.2 cm) 82-7/8” (210.
Cutout Dimensions 30” All Refrigerator/Freezer 24” ) cm (61.0 See an ti-tip b Electric Outlet Location oard in stallatio n 6” (15.2 cm) 9” (22.9 cm) 9” (22.9 cm) 82 (210 -7/8” .5 anti- cm) m in tip open board . & ing h eigh t 84 (213 -1/16” .5 anti- cm) m tip b ax. ope ning oard & heig ht 73-3 (186.4/8” cm) Water Line Entry Area Note: Shown for All Freezer only. 30 7-5/ 5/8 (1.5 ” cm) (76. 30” 2 cm ) (19.4 8” cm) 3” (7.6 (76.2 ” cm) 6-3/ (17.1 4” cm) cm) 5/8 (1.
Anti-Tip Dimensions 30” All Refrigerator/Freezer Anti-Tip Location 79 (201 -3/8” .6 to bo cm) min . ” 1-1/2m) (3.8 c anti- ttom of tip b oard 23” (58.4 c m) 8 (204 0-1/2” .6 to bo cm) max . anti- ttom of tip b oard 3- 1/2 (8.9 c ” m) One 2”x4” mounting One board 1-1/2” (3.8 cm) x 3-1/2” (8.9 cm) 2”x 4” mounting board Note: If unit is installed deeper than 24” (61.0 cm), then shim behind 1-1/2” (3.8 cm) x 3-1/2” (8.9 cm) Note: Ifboard unit is by installed deeper than 24” (61.
Cutout Dimensions 36” All Refrigerator/Freezer 24” ) cm (61.0 See an ti-tip b oard in Electric Outlet Location stallatio n 6” (15.2 cm) 9” (22.9 cm) 9” (22.9 cm) 82 (210 -7/8” .5 anti- cm) min tip . open board & ing h eigh t 84 (213 -1/16” .5 anti- cm) m tip b ax. ope ning oard & heig ht 73-3 (186.4/8” cm) Water Line Entry Area Note: Shown for All Freezer only. 36 7-5/ 5/8” (1.5 (91. 36” 5 cm ) cm) (19.4 8” cm) 3” (7.6 (91.5 ” cm) 6-3/ (17.1 4” cm) cm) 5/8 (1.
Anti-Tip Dimensions 36” All Refrigerator/Freezer Anti-Tip Location 79 (201 -3/8” .6 cm )m to ” 1-1/2m) (3.8 c bo in. anti- ttom of tip b oard 29” (73.7 c m) 8 (204 0-1/2” .6 to bo cm) max . anti- ttom of tip b oard 3- 1/2 (8.9 c ” m) One 2”x 4” mounting board 1-1/2” (3.8 cm) x 3-1/2” One 2”x4” mounting board 1-1/2” (3.8 (8.9 cm)cm) x 3-1/2” (8.9 cm) Note: If unit is installed deeper than 24” (61.0 cm), then shim Note: If unit is installed deeperboards than 24” (61.
Dimensions Dual 30” All Refrigerator/Freezer 2 3-1 (8.9 /2” cm ) (73 9” .7 c m) 3 (76 0” .2 c m) 2 (73 9” .7 c m) 3 (76 0” .2 c m) 9 –5 (23 /32” .3 c m) 75 -1 (19 5/1 2.9 6” cm ) ies varare) t en w d m ar ure lied h eas pp M ally (loc su 82– (210 3/4” .2 c min. m) t 8 o 4–1 (213 /16” .5 c max m) . 29 - (74 1/2” .9 c m) 29 - (74 1/2” .9 c m) 1 (2.5 ” be twe4 cm en ) uni t s ” 16 -3/ ) 23 .9 cm (58 4” -3/ 24.
Dimensions Dual 30” & 36” All Refrigerator/Freezer 2 3-1 (8.9 /2” cm ) (73 9” .7 c m) 3 (76 0” .2 c m) 3 (88 5” .9 c m) 3 (91 6” .5 c m) 9–5/3 75 2 (23.3 c ” m) ies varare) t en w -1 (19 5/1 2.9 6” cm ) d m ar ureplied h s a e sup M ally (loc 82–3 (210. /4” 2 cm min. ) to 84–1 / (213. 16” 5 cm max. ) 29 - (74 1/2” .9 c m) 35 - (90 1/2” .2 c m) 1 (2.5 ” be twe4 cm en ) uni t ” 16 -3/cm) 3 2 .9 (58 4” -3/ 24.
Dimensions Dual 36” All Refrigerator/Freezer 3 3-1 (8.9 /2” cm ) (88 5” .9 c m) 3 (91 6” .5 c m) 3 (88 5” .9 c m) 3 (91 6” .5 c m) 9–5/3 75 (23.3 c2” m) ies -15 var ) nt rdware e m a (19 /1 2.9 6” cm ) re d h asusupplie e M y all (loc 82–3 (210. /4” 2 cm min. ) to 84–1 / (213. 16” 5 cm max. ) 35 - (90 1/2” .2 c m) 35 - (90 1/2” .2 c m) 1 (2 ” be .54 c twe m en ) uni ” 16 -3/cm) 3 2 .9 (58 4” -3/ 24.
Specifications Dual All Refrigerator/Freezer* Description Overall width Overall height (from bottom) Overall depth (from rear) Cutout width Cutout height Cutout depth Electrical requirements Maximum amp usage Inlet water requirements (All Freezer only) Overall interior dimensions 30” freezer 30” refrigerator 36” freezer 36” refrigerator Maximum panel weight Approximate shipping weight (2) 30” Units (1) 36” & (1) 30” Unit (2) 36” Units 60” (152.4 cm) 66” (167.6 cm) 72” (182.9 cm) 82-3/4” (210.2 cm) min.
Cutout Dimensions Dual 30” All Refrigerator/Freezer See an 24” ) ti-tip b cm (61.0 oard in Electric outlet location stallatio n 6” (15.2 cm) 9” (22.9 9” (22.9 cm) cm) 82 (210 -7/8” .5 anti- cm) m in tip open board . & ing h eigh t 73-3 (186.4/8” cm) 84 (213 -1/16” .5 anti- cm) m tip b ax. ope ning oard & heig ht Water Line Entry Area Note: Cutout opening shown with All Freezer model on left. Reverse water line entry if All Freezer model is on right. 7-5/ (152 60” .4 cm ) 60 (19.
Anti-Tip Dimensions Dual 30” All Refrigerator/Freezer Anti-Tip Location 79 (201 -3/8” .6 cm )m to bo in. anti- ttom of tip b oard 23” 8 (204 0-1/2” .6 to bo cm) max ” 1-1/2m) (58.4 c m) (3.8 c . anti- ttom of tip b oard 23” (58.4 c m) 3- 1/2 (8.9 c ” m) One 2”x 4”board mounting per unit(3.8 cm) x 3-1/2” (8.9 cm) One 2”x4” mounting per board unit 1-1/2” 1-1/2” (3.8 cm) x 3-1/2” (8.
Cutout Dimensions Dual 30” & 36” All Refrigerator/Freezer 24” ) .0 cm See an ti-tip b (61 oard in Electric Outlet Location stallatio n 6” (15.2 cm) 9” (22.9 9” (22.9 cm) cm) 82 (210 -7/8” .5 anti- cm) min tip . open board & ing h eigh t 73-3 (186.4/8” cm) 84 (213 –1/16” .5 anti- cm) m tip b ax. ope ning oard & heig ht Water Line Entry Area Note: Cutout opening shown with All Freezer model on left. Reverse water line entry if All Freezer model is on right. 7-5/ (167 66” .
Anti-Tip Dimensions Dual 30” & 36” All Refrigerator/Freezer Anti-Tip Location 79 (201 -3/8” .6 cm )m to bo in. anti- ttom of tip b oard 29” 8 (204 0-1/2” .6 to bo cm) max ” 1-1/2m) (73.7 c m) (3.8 c . anti- ttom of tip b oard 23” (58.4 c m) 3- 1/2 (8.9 c ” m) One 2”x 4” mounting board per unit One 2”x4” mounting board 1-1/2” (3.8 cm) x 3-1/2” (8.9 cm) 1-1/2” (3.8 per cm) xunit 3-1/2” (8.9 cm) is installed deeper than24” 24” (61.0 (61.
Cutout Dimensions Dual 36” All Refrigerator/Freezer See an 24” (61.0 ti-tip b cm) oard in Electric Outlet Location stallatio n 6” (15.2 cm) 9” (22.9 9” (22.9 cm) cm) 82 (210 -7/8” .5 anti- cm) m in tip open board . & ing h eigh t 73-3 (186.4/8” cm) 84 (213 -1/16” .5 anti- cm) m tip b ax. ope ning oard & heig ht Water Line Entry Area Note: Cutout opening shown with All Freezer model on left. Reverse water line entry if All Freezer model is on right. 7-5/ (182 72” .9 cm ) 72 (19.
Anti-Tip Dimensions Dual 36” All Refrigerator/Freezer Anti-Tip Location 79 (201 -3/8” .6 to bo cm) min . anti- ttom of tip b oard 29” 8 (204 0-1/2” .6 to bo cm) max ” 1-1/2m) (73.7 c m) (3.8 c . anti- ttom of tip b oard 29” (73.7 c m) 3- 1/2 (8.9 c ” m) One 2”x 4” mounting board per unit One 2”x4” mounting board per unit 1-1/2” (3.8 cm) x 3-1/2” (8.9 cm) 1-1/2” (3.8 cm) x 3-1/2” (8.9 cm) Note: If unit is installed deeper than 24” (61.
Overlay Dimensions 30” Custom Panels ” 3/4cm) (1.9 36” Custom Panels 29 (74 1/4” .3 cm ) ” 3/4cm) (1.9 35 - (89 1/4” .5 c m) 75 (19 -1/2 1.8 ” cm ) 75 (19 -1/2 1.8 ” cm Note: Hardware placement can vary depending on single or dual installation. Note: Panel overlays must be dry, solid, straight one piece panels. The use of multiple panel pieces to achieve the dimensions is not recommended.
Custom Grille Dimensions 30” Custom Grille 1 (1.2/2” 7c m) s diu Ra ) ” 1/2 m) 3” m) 7c (1.2 2 (7.6 (10 1/64 .59 ” cm ) /8 1c m) (3.8 (14 7/32 .10 ” cm ) 1 ius /2 ad (1.27 ” cm ” R m) 4 1/ (.64 c ” 3” m) 2c -2 (63 7/3 .10 2” cm ) 3 /4” 3-3 cm) 3/4 (1.9 ” 0c m) ) 24 (7.6 Reverse dimensions for other end. 1 (1.2/2” 7c m) 1 cm 1 5-1 c (6. 2” -1/ ) 1 (.3 9 4-1 4” m 1/ (.16.42 c 3 (1.9/4” 0c m) ” /4 ) 2-38 cm (1.9/4” 0c m) 26 - (66 3/16 .51 ” cm ) 2 (9.
Custom Grille Dimensions 36” Custom Grille 1 (1.2/2” 7c m) s diu Ra ) 9 4” m 1/ (1.6.24 c 7c 3” m) (1.2 2c (10 1/64 .59 ” cm ) (7.6 (3.8 1 (14 7/32 .10 ” cm ) /8 ius /2 ad (1.27 ” cm ” R m) 4 1/ (.64 c ” m) 3” m) 2c (7.6 Reverse dimensions for other end. /4” 3-3 cm) 2 3 ) 30 -2 (78 7/3 .34 2” cm ) 3/4 (1.9/4” 0c m) 1 (1.2/2” 7c m) 1 cm 1 5-1 1 1c (6. 2” -1/ ) 4-1 ” 1/2 m) (.3 3 (1.9/4” 0c m) ” /4 ) 2-38 cm (1.9 ” 0c m) 32 - (81 3/16 .75 ” cm ) (9.
Custom Grille Dimensions Dual 30” Custom Grille 4-1 (1 1/6 1 (1.2/2” 7c m) ius ad ”R ) 1.2 4” 7c m) m 4 1/ (.16.24 c /2” 1 cm) 7 (1.2 1 (.3 ) cm 3” m) /4” 3-3 cm) ” cm ) - (66 3/16 .80 ” cm ) (7 3 (1.9/4” 0c m) 1 R 3/32” (0.09 cm) 9/16” (1.43 cm) (1.90 cm) .80 3/4” (1.90 cm) Grille support 2-7 (7.3 /8” 0c m) ” cm ) 35 -2 (89 5/6 4 .90 1 (2.5 ” 4c m ” cm ) ) /8” 3-5 m) 1/2 0c (1.2 ” 7c m) (9.2 54 (13 27/3 9 2 .30 3-3 cm) 2 3 1/2 (1.
Custom Grille Dimensions Dual 30” & 36” Custom Grille 4-1 (1 1/6 1 (1.2/2” 7c m) s diu Ra ) 1.2 4” 7c m) 4” m 1/ (.16.42 c /2” 1 cm) 7 (1.2 1 (.3 1/8 ” ) cm Reverse dimensions for other end. /4” 3-3 cm) 2 3 (1.9/4” 0c m) 2c (7.6 (6 3” m) (66 3/16 . 2c 3 Grille support 2-7 (7.3 /8” 0c m) 34 -1 (86 1/6 4 .80 (9.5 ” cm ) 35 1 (2.5 ” 4c m -2 (89 5/6 .90 4” cm ) 3- cm 0 (9.2 - /4” 3-3 cm) 2 62 (15 -3/64 7.6 ” 0c m) (16 64” 2.5 6c (9.
Custom Grille Dimensions Dual 36” Custom Grille 4-1 (1 1/6 1 (1.2/2” 7c m) s diu Ra ) 1.2 4” 7c m) 4” m 1/ (.16.24 c ” 1/2cm) .27 (1 3” m) 2c (7.6 1 (.3 ) cm Reverse dimensions for other end. /4” 3-3 cm) 2 3 (1.9/4” 0c m) (1.90 cm) 1 3 Grille support 2-7 (7.3 /8” 0c m) 40 (10 11/6 2.0 4” 4 cm ) (9.5 41 (10 25/6 5.1 4” 3 1 (2.5 ” 4c m cm 1 ) ) 8” -5/ ) (1.2/2” 7c m) 3 cm 0 (9.2 66 16927/3 .78 2” cm ) 4” -3/ ) 3 (1.9/4” 0c m) (1.2 ” 7c m) 3 cm 2 68 (17 -3/64 2.
Cabinet Information Custom panel models, (with 3/4” [1.9 cm], thick panels and custom handles locally supplied), fit flush in 25” (63.5 cm) deep (countertop depth) cabinet openings with no protrusion into room except custom handles Top View Wall 1/4” (.63 cm) space if 25” (63.5 cm) cabinet depth is used 25” (63.5 cm) countertop depth 3/4” (1.9 cm) full end panel 3/4” 1/8” (1.9 cm) (0.3 cm) overlay foam Door panel Flush Top View Wall 1/4” (.63 cm) space if 25” (63.
Cabinet Information Custom panel models can be installed in standard 24” (61.0 cm) deep openings. However, the door faces and top ventilation grille will protrude 3/4” (1.9 cm) into the room. This is ideal for alignment with full overlay cabinet doors. Top View Flush mount cabinet doors Wall 24” (61.0 cm) standard cabinet depth 3/4” 24-3/4” (1.9 cm) full end panel (62.9 cm) 3/4” 1/8” (1.9 cm) (0.
Custom Side Panel Dimensions Z-Bracket 1” (2.5 cm) 1/4” (0.6 cm) 4” -3/cm) 1 2 .2 (55 3/4” (1.9 cm) End panel 4” -3/ ) 21.2 cm (55 (2182-7 0.5 /8 cm ” to ) min 8 (21 4-1 . 3.5 /1 cm 6” )m ax .* Note: Adding 3/4” (1.9 cm) side panels adds an additional 3/4” (1.9 cm) to the overall width of the product for each side panel used. (2182-7 0.5 /8 cm ” t ) min (21 84-1o . 3.5 /1 cm 6” )m ax .* ” 24 cm) .0 (61 Note: Requires side panel hardware kit (SPHKDS).
Custom Panel General Information Custom finishing options • Panel thickness must not exceed 1” (2.5 cm) on hinge side. Thicker panels will interfere with door swing and clearance. • Door panels should be installed after the refrigerator has been plugged in for at least 24 hours. • All installations must allow for the refrigerator and freezer door to open a minimum of 90˚. • For side wall or corner installation, allow for a standard 3” (7.6 cm) cabinet filler to assure door(s) opens 90˚.
Custom Door Panel Installation 2 1 x2 x13 x13 Remove handle side cabinet screws and trim with a phillips screwdriver. x2 Remove all screws from handle side door trim. Remove two screws from top and bottom door trim. Remove handle side door trim. 4 3 2-1/16” (5.2 cm) 1-11/16” (4.3 cm) 2-13/16” (7.1 cm) Bottom-mount 12-1/16” (30.6 cm) All Refrigerator/ Freezer/ Side-by-side 2-1/8” (5.4 cm) Back of panel “Z” bracket Remove bracket.
Custom Door Panel Installation 7 8 x2 x13 x2 Reinstall handle side door trim and door trim screws. Slide custom wood panel to the hinge side, ensuring “Z” bracket engages the door bracket. 9 x13 Reinstall cabinet trim and screws.
Custom Grille Installation 2 1 Remove air grille center blade. Remove two 1/4” (0.6 cm) screws with a magnetic extended screwdriver at least 8” (20.3 cm) long. 3 4 Pull air grille assembly forward. Remove 2 mounting brackets from the grille air assembly. 5 6 Using eight screws removed from the mounting brackets, attach mounting brackets to the custom wood grille using predrilled pilot holes. (See grille overlay specifications for proper alignment and pilot hole placement.
Custom Grille Installation (cont.) 7 8 Install two 1/4” (0.6 cm) screws with a magnetic extended screwdriver at least 8” (20.3 cm) long. Install custom air grille center blade.
General Information Area Requirements A 115 volt, 60-Hz, 15 amp, fused, electrical supply is required. It is required that a separate circuit serving only this appliance be provided. This appliance is equipped with a power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong, grounding-type wall receptacle. DO NOT use an extension cord.
General Information Water Supply Requirements • Copper tubing route must be above 35˚ F (1.7˚ C) to prevent water line from freezing. WARNING • DO NOT use plastic water lines from the household plumbing to the water inlet valve connection on the refrigeration unit. To avoid serious illness or death, DO NOT use unit where water is microbiologically unsafe or of unknown quality, without adequate disinfection before or after the system.
General Information Tip Over Hazard • Most of the unit’s weight is at the top. Extra care is needed when moving the unit to prevent tipping. Appliance is top heavy and tips easily when not completely installed. Keep doors closed until appliance is completely installed and secured per installation instructions. Use two or more people to move and install the appliance. Failure to do so can result in death or serious injury. • DO NOT remove protective film until unit is in operating position.
Installation 1 2 Place unit in front of cutout. Pull the center grille louver up at an angle and pull out. 3 4 Using an 8” magnetic nut driver, remove the two 1/4” screws. Remove grille assembly. Hinge Adjustment 6 5 Front of unit 2 2 1 1 3 Loosen the four hinge screws. Adjust door. Retighten four hinge screws. Remove four side screws and remove unit top.
8a 7 1 Wall 2 2x4 Refrigerator Attach one 2 x 4 to wall stud (refer to dimensions page for exact location). Replace unit top and four side screws. 9 8b Wall 2x4 Refrigerator Plug in power cord to verify operation. Note: Make sure power switch and showroom switch are in the “On” position. If needed, depending on cabinet and depth, attach second 2 x 4 to first 2 x 4. 10b 10a 3” Carefully move unit until semi flush with cabinet (depending on unit).
12 11 Flush water line by running two quarts of water into a bucket. Turn water off Pull supply tubing forward under unit. Note: DO NOT use plastic water lines. 14 13 Connect supply tube to water valve using a 1/2” wrench. Note: DO NOT overtighten. Turn on water supply and check for leaks. 16 15 Screw Wall 2x4 Refrigerator Attach positive secure self-tapping bolts to 2 x 4 using a 22” extension. Lift unit off rollers to desired height and level unit using a 5/16” head wrench.
17 Verify that drain pan is installed and aligned. Kickplate Installation 18 19 1 1 2 3 2 Align holes on both ends of louvered panels and insert screws. Using a phillips screwdriver, attach the kickplate to the unit and adjust to desired height. Door Stop Adjustment 20 21 1 1 120˚ 110˚ 90˚ 3 2 2 Open refrigerator door so door stop and shoulder screw are accessible. Note: Shoulder screw should be in 110˚ door opening position. 42 Remove shoulder screw and place in 90˚ or 120˚ position.
Final Installation 29 28 Replace top air grille. Using an 8” magnetic nut driver, replace the two 1/4” screws. 30 31 Replace the center grille louver. Open door. The display should flash. 32 Press “ACTIVATE CONTROLS” pad and close door. Note: There is a 6 minute delay before the unit starts.
Performance Checklist Verify cabinet size. Align/square door(s). Verify electrical supply and water supply (if applicable). Verify drain pan is properly installed and there are no leaks on water connection. Install anti-tip device(s) and verify unit is secure. Install kickplate. Remove internal packaging and labels and wipe unit down. Position unit in cutout, level at desired height and secure unit. Plug-in unit and verify operation.
Verify Operations Control Panels All Refrigerator FREEZER ACTIVATE CONTROLS REF TEMP HIGHER LOWER HIGHER LOWER CF MAX FRZ MAX REF FAST COOL SAB SHOW REFRIGERATOR DOOR OPEN POWER HIGH TEMP FAST COOL MAX REF ALARM OFF DISPLAY OFF REFRIGERATOR DOOR OPEN POWER HIGH TEMP FAST COOL MAX FRZ ALARM OFF DISPLAY OFF All Freezer FREEZER ACTIVATE CONTROLS FRZ TEMP CF MAX FRZ MAX REF FAST COOL SAB SHOW 1. Press “Activate Controls” pad. 2. Verify unit is not in Sabbath Mode. If in Sabbath Mode: A.
Service & Registration If service is required, call your authorized service agency. Have the following information readily available. • Model number • Serial number • Date purchased • Name of dealer from whom purchased Clearly describe the problem that you are having.
Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-(845-4641) or visit our web site at vikingrange.
