Table of Contents Warnings & Important Information 3 All Refrigerator/Freezer Dimensions & Specifications (30 and 367) 6 Cutout Dimensions (30) 8 Anti-Tip Dimensions (307) 9 Cutout Dimensions (36) 10 Anti-Tip Dimensions {36") 1" Dimensions (Dual 30%} 12 Dimensions (Dual 30" and 367) 13 Dimensions (Dual 36") 14 Specifications (Dual) 15 Cutout Dimensions (Dual 307) 16 Anti-Tip Dimensions {Dual 307) 17 Cutout Dimensions (Dual 30” and 36") Anti-Tip Dimensions {Dual 30” and 367) _ 19 Cutout Dimensions (Dual 36")
IMPORTANT Please Read and Follow # Make sure that incoming voltage is the same as unit rating. An electric rating plate specifying voltage, frequency, wattage, amperage, and phase is attached to the product. * To reduce the risk of fire, electrical shock, or injury to persons, installation work and electrical wiring must be done by a qualified technician in accordance with all applicable codes and standards, including fire-rated construction.
IMPORTANT — Please Read and Follow! A GF| shall be used if required by PAN-70 (National Electric Code), federal/state/local laws, or local ordinances. ® The required use normally related to the location of a receptacle with respect to any significant sources of water or moisture. * Viking Range, LLC will NOT warranty any problems resulting from GF outlets which are not installed properly or do not meet the requirements below.
A WARNING TIP OVER HAZARD » Appliance is top heavy and tips easily when not completely installed. Keep doors closed until appliance is completely installed and secured per installation instructions. Use two or more people to move and install appliance. Failure to do so can result in death or serious injury. A WARNING ELECTRICAL SHOCK HAZARD Disconnect power or turn Ww power disconnect switch to QFF position before removing top grille. Failure to do so can result in death or electric shock.
Specifications 30" (76.2 cm) (210.2 crn} min, to {213.5 cm) max. To front edge of side trim: (58.9 cm) To front edge of door trim: 24 {61.0 cm} 30” (76.2 em} 827/87 {210.5 em) min. to (213.5 cm} max. 74" (61.0 cm) min.* 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with grounded 3: lug attached to 9.1 amps 5.7 amps 1/4" copper thing inlet waterline; minimum 20 psi; N/A maximum 120 psi 15.9 cu. ft. {450 liters) 18.4 cu. ft. (522 liters) 50 lbs. (22.7 kg) 445 Ibs. (200.2 kg) (210.2 crn} min, to {213.
Cutout Dimensions 30" All Refrigerator/Freezer Electric Outlast Location 832, i R108 Ves ! ign iin, i nine wey ate Ring hei a i 73 37g = ! (185.4 : Tatar Line Entry Area Note: Shown for All pbk only.
Anti-Tip Dimensions 30” All Refrigerator/Freezer i-Tip Location One 2"x4" mounting beard {3.8 cm) x (8.9 cm) Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting board by the difference. Bottom of anti-tip board is (9.8 cm) below the opening height. Note: Top of unit must be placed firmly under anti-tip board.
Cutout Dimensions 36" All Refrigerator/Freezer Electric Outlet Location / / / 73-31 ies 4 omy Water Line Entry Area Mort: Shown for All Freezer only.
Anti-Tip Dimensions 36" All Refrigerator/Freezer One 2"x4" mounting board {3.8 cm) x (8.9 cm) Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting board by the difference. Bottom of anti-tip board is (9.8 cm) below the opening height. Note: Top of unit must be placed firmly under anti-tip board.
Specifications (152.4 cm) 66" (167.6 cm) 72" (182.9 cm) (210.2 crn} min, to {213.5 cm) max. To front edge of side trim: (58.9 cm} To front adj of door trim: 24% {61.0 cm) 80° (152.4 cm) 66" (167.6 cm) 72° (182.9 cm) cm) min. to 84-1716" (213.5 em) max. 247 (61.0 cm) min. > 12) 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with grounded 3: lug attached to FD 30" 9.1 amps. FDR 30" 5.7 amps FD 36" 9.5 amps FDR 36" 6.5 amps 1/4" copper tubing inlet waterline; minimum 20 psi; maximum 120 psi 15.9 cu.
Anti-Tip Dimensions Dual 30" All Refrigerator/Freezer Anti-Tip Location One 2"x4" mounting board per unit (3.8 cm) x (8.9 cm) Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting board by the difference. Bottom of anti-tip board is (9.8 cm) below the opening height. Note: Top of unit must be placed firmly under anti-tip board.
Anti-Tip Dimensions Dual 30” & 36” All Refrigerator/Freezer Ant Tip Location One 2"x4" mounting board per unit {3.8 cm) x (8.9 cm} _ Note: If unit is installed deeper than 24” (61.0 cm), then shim behind the mounting board by the difference. Bottom of anti-tip board is (9.8 cm) below the opening height. Note: Top of unit must be placed firmly under anti-tip board. | Note: Dimensions shown for 36” All Freezer/All Refrigerator model on the left. Reverse mounting boards if units are installed on the right.
Cutout Dimensions Dual 36" All Refrigerator/Freezer Electric Outlet Location , wt Tir Pong orc 8 73.3, ox daa, m Boars R135 Vang ~— iia) Water Line Entry Ares Note: Cutout opening shown with All Freezer model on left. Savor water Lina sentry if All Freezer mods! is ort right.
Anti-Tip Dimensions Dual 36” All Refrigerator/Freezer Anti-Tip Location One 2"x4" mounting board per unit (3.8 cm) x (8.9 cm) Note: If unit is installed deeper than 24 (61.0 cm), then shim behind the mounting board by the difference. Bottom of anti-tip board is (9.8 cm) below the opening height. Note: Top of unit must be placed firmly under anti-tip board.
Overlay Dimensions 30" Custom Panels Note: Hardware placement can vary depending on single or dual installation. Note: Panel overlays must be dry, solid, straight one piece panels. The use of multiple panel pieces to achieve the dimensions is not recommended.
Custom Grille Dimensions 30" Custom Grille for ether and. Soy iz Note: Optional hinge cover can be attached using a strong VHB tape, countersunk wood screws or short nails from a nail gun.
Custom Grille Dimensions 36" Custom Grille Reverse dimensions. for other end. Note: Optional hinge cover can be attached using a strong VHB tape, countersunk wood screws or short nails from a nail gun.
Custom Grille Dimensions Dual 30” Custom Grille for other end. Bose: This part should be Ba, rig pb grille, ive, toe per rife Likes Jan be used by dividing the length of the grille into thirds, | ny, Note: Dual units can only be made in a left and right hand configuration. Note: To use a custom grille on a dual installation, you must purchase the center trim kit FCTKSS. Note: Optional hinge cover can be attached using a strong VHB tape, countersunk wood screws or short nails from a nail gun.
Custom Grille Dimensions Dual 30" & 36” Custom Grille war lite play an Sty | Nita: This pent should be located at the center of the grille, If desired, two per grille can be used by dicing the length of the grills info thirds. Note: Dual units can only be made in a left and right hand configuration. Note: To use a custom grille on a dual installation, you must purchase the center trim kit FCTKSS. Note: 30 unit is on left and 36” unit is on right.
Custom Grille Dimensions Dual 36" Custom Grille Riots: This part should be fasted at the nectar of the 4 grille. f desired, two per girls 30k zan be used by dividing the i. length of tha girls into thirds. Note: Dual units can only be made in a left and right hand configuration. Note: To use a custom grille on a dual installation, you must purchase the center | trim kit FCTKSS. Note: Optional hinge cover can be attached using a strong VHB tape, countersunk wood screws or short nails from a nail gun.
Cabinet Information Custom panel models, (with 3/4 [1.9 cm], thick panels and custom handles locally supplied), fit flush in 25" (63.5 em} deep {counter top depth) cabinet openings with no protrusion into room except custom handles _ cabinet depth {88.5 ard is used cou \ depth (18cm) »| = $i8on | full need panel standard : cabinet 144” cabinet depth is used 374" 1.
Cabinet Information Custom panel models can be installed in standard 24” (61.0 cm) deep openings. However, the door faces and top ventilation grills will protrude 3/4” (1.9 cm) into the room. This is ideal for alignment with full overlay cabinet doors. Top View Flush mount cabinet doors 3a” 19am} full snd pans! 3/4" que {1.9 em) oF eam) _overlay foe.
Custom Side Panel Dimensions / 2. Beacket 23am) Je #1520, Mag & frp an y by dap Uy, Sg J6e Sy, Note: Adding 3/4* wx (1.9 cm) side panels adds an additional 3/4” (1.9 cm) to the overall width of ~ the product for each side panel used. Note: Requires side panel hardware kit (SPHEROID. PN Options! kick plate notch rey (Dimensions determined by cabinets) ree *Note: Depending on how high leveling feet are raised, and cabinet enclosure height.
Custom Panel General Information Custom finishing options # All installations must allow for the refrigerator and freezer door to open a minimum of 90°. # For side wall or comer installation, allow for a standard 3" (7.6 cm) cabinet filler to assure doors) opens 90°. Note: if a custom handle is used, a wider filler may be necessary. Hn Panel thickness must not exceed 17 (2.5 cm) on hinge side. Thicker panels will interfere with door swing and clearance.
Custom Door Panel Installation Remove handle side cabinet screws and trim with a fillips screwdriver. Remove two screws from top and bottom door trim. Remove handle side door trim. Remove bracket. Attach "Z” bracket to the hinge side of custom panel. Push custom wood panel onto door. Attach bracket to the handle side of custom panel.
Custom Door Panel Installation Slide custom wood panel to the hinge side, ensuring “Reinstall handle side door trim “Z* bracket engages the door bracket. and door trim screws. Reinstall cabinet trim and screws.
Custom Grille Installation Remove air grille center blade. Remove two 1/4" (0.6 cm) screws with a magnetic extended screwdriver at least 8” (20.3 cm} long. Pull air grille assembly forward, Remove 2 mounting brackets from the grille air assembly. Using eight screws removed from the mounting brackets, Insert custom air grille assembly. attach mounting brackets to the custom wood grille using pro drilled pilot holes.
Custom Grille Installation cont) Install two 1/4 {0.6 cm} screws with a magnetic Install custom air grille center blade. extended screwdriver at least 8” (20.3 cm) long.
General Information Area Requirements Verify the following: # Unit can fit into residence and can be moved around comers and through doorways. * Floras can support unit's weight plus food weight (approximately 1200 pounds [540 kg] per unit). * Floors underneath refrigerator are level with surrounding finished floor. * Rear wall is solid and is able to support two horizontally mounted 2 x 4s (included) bolted to two wall studs. The 2 x 4 board bolt heads must be fish with prevent obstruction.
General Information Water Supply Requirements ALL Te To avoid serious illness or death, DO NOT use unit where water is micro biologically unsafe or of unknown quality, without adequate disinfection before or after the system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts. The contaminants or other substances removed or reduced by this water treatment system are not necessarily in your water. Use only 1/4” (6 mm) copper tubing for water line.
General Information * Most of the unit's weight is at the top. Extra care is needed when moving the unit to prevent tipping. * DO NOT remove protective film until unit is in operating position. # All four leveling legs must make contact with the floor to support and stabilize the full weight. « DO NOT drop unit. « Remove exterior shipping materials prior to moving unit inch home. « Use two or more people to move and install unit. Failure to follow this instruction can result in back or other injury.
Installation Pull the center grille louver up at an angle and pull out. Using an 8” magnetic nut driver, Remove grills assembly. remove the two 1/4” screws. Hinge Adjustment Remove four side screws and remove unit top. Loosen the four hinge screws. Adjust door. Re tighten four hinge screws.
Refrigerator Attach one wall stud {refer to for exact location). Refrigerator If needed, depending on cabinet and depth, Plug in power cord to verify operation. attach second 2x 4 to first 2x 4. Note: Make sure power switch and showroom switch ars in the "On" position. Place unit within 3” of being flush with cabinets. Carefully move unit until semi flush with cabinet Note: To avoid cabinet damage, place cardboard (depending on unit). between cabinets and unit.
Pull supply tubing forward under unit. Flush water line by running two quarts of water Note: DO NOT use plastic water lines. into a bucket. Turn water off Connect supply tubs to water valve using a 172% wrongness Soto: DO NOT overweight. Turn on water supply and check for leaks. Refrigerator Lift unit off rollers to desired height Attach positive secure self-tapping bolts and level unit using a 5/16" head wrench. using a 22” extension. Nate: DO NOT use an electric device. Overestimating can cause damage.
Verify that drain pan is installed and aligned. Kick plate Installation SEE Be gma Align holes on both ends of louvered panels Using a Philips screwdriver, attach the and insert screws. kick plats to the unit and adjust to desired height Door Stop Adjustment ~ Open refrigerator door so door stop and Remove shoulder screw and place in 90" shoulder screw are accessible. or 120° position. Note: Shoulder screw should be in 110° door opening position.
Final Installation Replace the canter grills louver. Press "ACTIVATE CONTROLS” pad and close door. Note: Hers is a & minute delay forbears the unit starts. 43 Using an 8” magnetic nut driver, replace the two 1/4” screws. Open door.
Performance Checklist Q Verify cabinet size. Q Verify electrical supply and water supply {if applicable). Q Install anti-tip device(s) and verify unit is secure. 0 Position unit in cutout, level at desired height and secure unit. Q Plug-in unit and verify operation. 0 Connect water supply (if applicable). + Verify ice maker fill tube is properly inserted. * Verify ice maker bail arm is down. * Verify dispenser operation (if applicable).
Verify Operations Control Panels All Refrigerator scarecrow ser y war wax mama | og COOT Tenn HIGHER LOWER COOL. REF OFF oF All Freezer acre rz ev ar wae oa | ome CONTROLS TEMP HER ® oot RZ OFF OFF 1. Press “Activate Controls” pad. 2, Verify unit is not in Sabbath Mode. If in Sabbath Mode: A. The Sabbath Mode will disable the interior lights, display (except SAB indicator, temperature and compartment indicator} and alarm. To exit the Sabbath Mode: B.
Service & Registration If service is required, call your authorized service agency. Have the following information readily available. * Model number # Serial number * Date purchased * Name of dealer from whom purchased Clearly describe the problem that you are having.
Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call or visit our web site at vikingrange.com in the US or brigade.