Viking Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site at vikingrange.
Table of Contents Warnings & Important Information ____________________________________________________________________3 Bottom-Mount Dimensions and Specifications (36”) __________________________________________________________6 Cutout Dimensions (36”) ____________________________________________________________________8 Anti-Tip Dimensions (36”) ___________________________________________________________________9 Overlay Dimensions (36”) __________________________________________________________________10
IMPORTANT–Please Read and Follow! A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local laws, or local ordinances. • The required use of a GFI is normally related to the location of a receptacle with respect to any significant sources of water or moisture. • Viking Range Corporation will NOT warranty any problems resulting from GFI outlets which are not installed properly or do not meet the requirements below.
Dimensions Specifications (Bottom-Mount) 36” Bottom-Mount (Bottom-Mount) 36” Bottom-Mount Description Overall width Overall height (from bottom) Overall depth (from rear) 3 (88 5” .9 c m) 3-1 (8.9 /2” cm ) Cutout width Cutout height Cutout depth Electrical requirements 36 (91 ” .4 c m) Maximum amp usage Inlet water requirements 51 (13 -7/8 1.
Cutout Dimensions Anti-Tip Dimensions (Bottom-Mount) 36” Bottom-Mount 24” ) cm (61.0 See an ti-tip b oa rd inst a (Bottom-Mount) 36” Bottom-Mount Electric Outlet Location llation 6” (15.2 c m) Anti-Tip Location 9” (22.9 cm) 9” (22.9 c m) 79 peni ng rd & heig ht 29” (73.7 c m) 8 (204 0-1/2” .6 to bo cm) max . ttom a / (213 .5 16” anti- cm) m t a op ip boa x. r g he d & ight (3.8 c anti- ttom of tip b oard 84-1 enin ” 1-1/2m) (201 -3/8” .6 to bo cm) min . 82 (210 -7/8” .
Overlay Dimensions (Bottom-Mount) Custom Grille Dimensions 36” Custom Panels 36” Custom Grille 1 s diu Ra ) ” m 4 c 1/ 6.24 (1.2/2” 7c m) 35 - (10 1/64 .59 ” cm ) 3” m) 7 (1.2 2c (7.6 (13 -1/4 0.2 ” 2c (7.6 0 .6 (4 3/1 6” ) cm 3 (7.6 ” 2c m) /4” 3-3 cm) 3 3 (.2 /3 4 2” cm ) 1-1 0c 5/ (1.6 8” cm ) 5 (1.6/8” cm ) 32 Note: Inset shown upside down. -1/ 4 (1.9/4” 0c m) .34 m) ” cm ) 32 -3 (81 /16 . 75 ” cm ) 2 (9.5 51 (13 -7/8 1.8 ” cm ) /8” 3-5 cm) 1 (1.
Custom Grille Dimensions Dimensions (Bottom-Mount) (Side-By-Side) Dual 36” Custom Grille 4-1 1 1 (1.2/2” 7c m) s diu Ra ) ” m 4 1/ (1.6.24 c (11 /64 .27 ” cm ) (.3 1/8 1c ” m) Reverse dimensions for other end. 3 (1.9/4” 0c m) /4” 3-3 cm) (9.5 (14 /32 .04 ” cm ) 3” m) 7 (1.2 /2” 1-1 cm) 5-1 7 ” 1/2cm) 2c (7.6 ” /4 ) 2-38 cm (1.90 cm) 0c m) 9 (6. 1 m) 32 -3 m 4 1/ (.64 c 1.2 7 (7.6 3 (1.9/4” 0c m) 9/16” (1.43 cm) cm ) 1 3/4” (1.90 cm) Grille support 2- 7 (7.
Dimensions Specifications (Side-By-Side) 48” Side-By-Side 42” Side-By-Side Description Overall width Overall height (from bottom) Overall depth (from rear) 4 (11 7” 9.4 cm ) 3-1 (8.9 /2” cm ) 75 -1 (19 5/1 2.9 6” cm ) (Side-By-Side) Cutout width Cutout height Cutout depth Electrical requirements 4 (12 8” 1.
Cutout Dimensions 24” ) .0 cm (61 Anti-Tip Dimensions (Side-By-Side) 42” Side-By-Side 42” Side-By-Side See an ti-tip b oa rd inst a (Side-By-Side) Electric Outlet Location llation 6” (15.2 c m) Anti-Tip Location 9” (22.9 cm) 9” (22.9 c m) 79 (201 -3/8” .6 to bo cm) min . 82 (210 -7/8” .5 anti- cm) mi tip n. 35” (88.9 c m) 8 (204 0-1/2” .6 to bo cm) max . ttom a 84-1 / (213 .5 16” anti- cm) m t a op ip boa x. r g he d & ight (3.
Cutout Dimensions 4” 2 cm) (61.0 Anti-Tip Dimensions (Side-By-Side) 48” Side-By-Side 48” Side-By-Side See an ti-tip b oa rd inst a (Side-By-Side) Electric Outlet Location llation 6” (15.2 c m) Anti-Tip Location 9” (22.9 cm) 9” (22.9 c m) 79 82 (201 -3/8” .6 to bo cm) min . (210 –7/8” .5 anti- cm) mi tip n. 84 r g he d & ight (3.8 c 41” (104.1 8 (204 0-1/2” .6 c (213 –1/16” .5 anti- cm) m t a op ip boa x.
Overlay Dimensions 42” Custom Panels ” 3/4 ) (1.9 cm 18 -3 (46 /16 .2 c ” m) ” 3/4cm) (1.9 cm 22 18 ” 3/4cm) -13 (57 /16 .9 c ” m) -3 (46 /16 .2 c ” m) (1.9 31 -1 (47 1/16 .5 c ” m) ” 3/4cm) (1.9 ” 3/4cm) - cm ) (1.9 31 10 -1 12 - 75 75 (19 -1/2 1.8 ” cm ) 3/8” (1.0 cm) 14-1/2” (36.8 cm) 5/16” (0.8 cm) radius 12-15/16” (32.9 cm) - (31 3/8” .4 c m) (19 -1/2 1.8 ” cm ) / (8.0 32” cm ) 20 - (27 1/16 .1 c ” m) 3-5 Dispenser Dimensions -5 (71 /16 .
Custom Grille Dimensions Custom Grille Dimensions (Side-By-Side) 42” Custom Grille 48” Custom Grille 1 1 (1.2/2” 7c m) 3 (1.9/4” 0c m) ” /4 ) 2-38 cm 9 ” 1/2cm) 3” m) c cm ) ” 1/4 ) 3 cm ) 3- cm (1.9/4” 0c m) 2 (9.5 3 (1.9/4” 0c m) 26 (66 3/16 .51 ” 2c (7.6 (. 30 -2 (7 7/3 (1.9/4” 0c m) 8.3 2” 4c m) 3- cm 2 (9.5 32 (81 3/16 cm ) 1 (1.2/2” 7c m) 0 (9.2 (10 40” 1.6 0c /4” 3-3 cm) 3 (1.9/4” 0c m) 2 39 (10 15/1 1.4 6” 4 cm ) /8” 3-1 cm) 1 3 (7.9 (1.
Dimensions Specifications (All Refrigerator/Freezer) 30” All Refrigerator/Freezer 30” All Refrigerator/Freezer Description Overall width Overall height (from bottom) Overall depth (from rear) 2 (73 9” .7 c m) 3 -1 (8.9 /2” cm ) 36” All Refrigerator/Freezer 30 (76 ” .2 c m) 75 (88 5” .9 c m) 3-1 (8.
Cutout Dimensions Anti-Tip Dimensions (All Refrigerator/Freezer) 30” All Refrigerator/Freezer 30” All Refrigerator/Freezer 4” 2 cm) (61.0 See an ti-tip b oa rd inst a (All Refrigerator/Freezer) Electric Outlet Location llation 6” (15.2 c m) Anti-Tip Location 9” (22.9 cm) 9” (22.9 c m) 79 (201 -3/8” .6 to bo cm) min . 82 (210 -7/8” .5 r g he d & ight 23” (58.4 c m) 8 (204 0-1/2” .6 to bo cm) max . ttom a 84 enin (3.8 c anti- ttom of tip b oard anti- cm) mi ti n open p board .
Cutout Dimensions 24” ) .0 cm (61 Anti-Tip Dimensions (All Refrigerator/Freezer) 36” All Refrigerator/Freezer 36” All Refrigerator/Freezer See an ti-tip b oa rd inst a Electric Outlet Location llation 6” (15.2 c m) Anti-Tip Location 9” (22.9 cm) 9” (22.9 c m) 79 (201 -3/8” .6 to bo cm) min . 82 (210 -7/8” .5 anti- cm) mi tip n. (3.8 c 29” (73.7 c m) 8 (204 0-1/2” .6 to bo cm) max . ttom a 84-1 / (213 .5 16” anti- cm) m t a op ip boa x.
Dimensions Dimensions (All Refrigerator/Freezer) Dual 30” All Refrigerator/Freezer (All Refrigerator/Freezer) Dual 30” & 36” All Refrigerator/Freezer 2 2 3-1 (8.9 /2” cm ) (73 9” .7 c m) 3-1 (8.9 /2” cm ) 30 (76 ” .2 c m) 2 (73 9” .7 c m) (73 9” .7 c m) 3 (76 0” .2 c m) 3 (88 5” .9 c m) 3 3 (76 0” .2 c m) 75 -1 (91 6” .5 c m) 75 es ari t v are) (19 5/1 2.9 6” cm ) ies varare) t n w me ard ureplied h s a p Meally su -1 (19 5/1 2.
Dimensions Specifications (All Refrigerator/Freezer) Dual 36” All Refrigerator/Freezer Dual All Refrigerator/Freezer* Description Overall width Overall height (from bottom) Overall depth (from rear) 3 3-1 (8.9 /2” cm ) (88 5” .9 c m) 3 (91 6” .5 c m) Cutout width Cutout height Cutout depth Electrical requirements 3 (88 5” .9 c m) 3 (91 6” .
Cutout Dimensions Anti-Tip Dimensions (All Refrigerator/Freezer) Dual 30” All Refrigerator/Freezer See an ti-tip b oa 24” ) .0 cm (61 rd inst a (All Refrigerator/Freezer) Dual 30” All Refrigerator/Freezer Electric outlet location llation 6” (15.2 c m) Anti-Tip Location 9” (22.9 cm 9” (22.9 ) c m) 79 82 (201 -3/8” .6 to bo cm) min . (210 -7/8” .5 anti- cm) mi tip n. open board & ing h eigh t 73-3/ 8 anti- ttom of tip b oard ” (186.4 cm ) / (213 .
Cutout Dimensions Anti-Tip Dimensions (All Refrigerator/Freezer) Dual 30” & 36” All Refrigerator/Freezer See an ti-tip b oa 24” ) .0 cm (61 rd inst a (All Refrigerator/Freezer) Dual 30” & 36” All Refrigerator/Freezer Electric Outlet Location llation 6” (15.2 c m) Anti-Tip Location 9” (22.9 cm 9” (22.9 ) c m) 82 (210 -7/8” .5 anti- cm) mi tip n. open board & ing h eigh t 73-3/ 8 79 (201 -3/8” .6 cm )m to bo in. anti- ttom of tip b oard ” (186.4 cm ) 29” 8 84–1 (204 0-1/2” .
Cutout Dimensions Anti-Tip Dimensions (All Refrigerator/Freezer) Dual 36” All Refrigerator/Freezer Dual 36” All Refrigerator/Freezer See an ti-tip b oa 24” ) .0 cm (61 rd inst a (All Refrigerator/Freezer) Electric Outlet Location llation 6” (15.2 c m) Anti-Tip Location 9” (22.9 cm 9” (22.9 ) c m) 82 79 (210 -7/8” .5 anti- cm) mi tip n. open board & ing h eigh t 73-3/ 8 (201 -3/8” .6 to bo cm) min . anti- ttom of tip b oard ” (186.4 cm ) 29” 8 (204 0-1/2” .6 to bo cm) max .
Overlay Dimensions Custom Grille Dimensions (All Refrigerator/Freezer) 30” Custom Panels (All Refrigerator/Freezer) 30” Custom Grille 1 ” 3/4cm) (1.9 29 s diu Ra ) ” m /4 24 c 36” Custom Panels (1.2/2” 7c m) 1 (1.6. - (74 1/4” .3 c m) 3” m) 7 (1.2 ” 3/4 ) (1.9 cm 35 (.3 1/8 1c ” m) - (89 1/4” .5 c m) 0c m) 1 (1.2/2” 7c m) 75 1 (1.2/2” 7c m) 1 (3.8 5- 1 (14 7/32 1 ius /2 ad) (1.27 ” R cm 4” m ) 1 / 64 c .10 ” cm ) (. 24 -2 (6 7/3 2c (7.6 3.
Custom Grille Dimensions Custom Grille Dimensions (All Refrigerator/Freezer) Dual 30” Custom Grille 36” Custom Grille (1.2/2” 7c m) 3 (1.9/4” ” /4 ) 2-3 cm (.3 1/8 1c ” m) c 1- cm 1 (10 1/64 . 59 ” cm ) Reverse dimensions for other end. c /4” 3-3 cm) 3 (1.9/4” m) m) 3 (1.9/4” 0c m) 32 -3 (81 /16 .75 ” cm ) 2 (9.5 m) Reverse dimensions for other end. 30 -2 (78 7/3 .34 2” c 3 (1.9/4” 0c (.3 1/8 1c ” m) /4” 3-3 cm) (14 /32 .04 ” cm ) 3” m) 2 (7.6 c 98 m) 26 -3 3/4” 3 (1.
Custom Grille Dimensions Custom Grille Dimensions (All Refrigerator/Freezer) Dual 30” & 36” Custom Grille (11 /64 .27 ” cm ) 2c 24 -2 (63 7/3 .10 2” c m) 3” m) 13/32” (1.03 cm) 3 (1.9/4” 0c m) (1.90 cm) Grille support .30 cm ) 34 -1 (86 1/6 .80 4” c c 60 (15 27/3 4.5 2” 4 3 1 (1.2/2” 7.4 6” 8c m) (16 64” 2.5 6c 7c (1. 1/2 27 ” cm ) m) 2-7 cm ) 2 (9.5 1 (2.5 ” 4c m) /8” 3-5 m) 0c (9.2 66 16927/3 .78 2” /4” 3-3 cm) (17 70” 7.8 0c 2 (9.
Cabinet Information Cabinet Information Custom panel models, (with 3/4” [1.9 cm], thick panels and custom handles locally supplied), fit flush in 25” (63.5 cm) deep (countertop depth) cabinet openings with no protrusion into room except custom handles Custom panel models can be installed in standard 24” (61.0 cm) deep openings. However, the door faces and top ventilation grille will protrude 3/4” (1.9 cm) into the room. This is ideal for alignment with full overlay cabinet doors.
Custom Side Panel Dimensions Custom Panel General Information Custom finishing options Z-Bracket • All installations must allow for the refrigerator and freezer door to open a minimum of 90˚. • For side wall or corner installation, allow for a standard 3” (7.6 cm) cabinet filler to assure door(s) opens 90˚. 1” (2.5 cm) • Panel thickness must not exceed 1” (2.5 cm) on hinge side. Thicker panels will interfere with door swing and clearance. 1/4” (0.6 cm) 4” -3/cm) 1 2 .
Ice and Water Dispenser Bezel Removal 5 (if required cont.) 6 Custom Door Panel Installation 2 1 Remove handle side cabinet screws and trim with a phillips screwdriver. Remove mounting support. 7 8 3 x2 x13 x13 Remove 2 additional screws under top section of bezel. (Refrigerator or Freezer) x2 Remove all screws from handle side door trim. Remove two screws from top and bottom door trim. Remove handle side door trim. 3 4 2-1/16” (5.2 cm) 1-11/16” (4.3 cm) 2-13/16” (7.
Custom Door Panel Installation 7 Custom Freezer Door Panel Installation (Bottom-Mount Only cont.) (Refrigerator or Freezer cont.) 2 1 8 x2 x13 x2 Reinstall handle side door trim and door trim screws. Slide custom wood panel to the hinge side, ensuring “Z” bracket engages the door bracket. x16 Open freezer door. Remove door trim screws and door trim with a phillips screwdriver. Remove bracket. 3 9 4 2-1/16” 2-1/16” (5.2 cm) (5.2 cm) 1-11/16” x13 1-11/16” (4.3 cm) (4.
Ice and Water Dispenser Bezel Installation (if required) 2 1 Install custom wood panels per product’s installation instructions. Ice and Water Dispenser Bezel Installation (if required cont.) 7 Locate opening in door and position bezel. Note: Graphics on bezel will be on top end, tilt slightly forward to allow water tube clearance. 3 Install two screws in lower part of bezel but DO NOT tighten all the way. 5 6 For a left hinge door, cut 5/8” x 2-3/4” in lower left corner.
Bottom-Mount Custom Panel Hinge Cutout (if required) 1 2 Custom Grille Installation (cont.) 3 ” 32 ) 3/.24 cm 4 ( 1 (4 . - 1 3 / 60 1 6 cm ” ) 3 5/ (1.6 8” cm ) 2 1 3 (7.6 ” 2c m) For a left hinge door, cut 5/8” x 3” in lower left corner. Note: Steps show panel upside down and notched for left hinge application. Mirror dimensions for right hinge door. 1 3 5/ Pull air grille assembly forward. Measure and cut 2-1/16” diagonal in lower left corner.
General Information General Information Area Requirements Water Supply Requirements A 115 volt, 60-Hz, 15 amp, fused, electrical supply is required. It is required that a separate circuit serving only this appliance be provided. This appliance is equipped with a power supply cord having a 3-prong grounding plug. To minimize possible shock hazard, the cord must be plugged into a mating 3-prong, grounding-type wall receptacle. DO NOT use an extension cord.
Installation General Information 1 2 Tip Over Hazard • Most of the unit’s weight is at the top. Extra care is needed when moving the unit to prevent tipping. • DO NOT remove protective film until unit is in operating position. • All four leveling legs must make contact with the floor to support and stabilize the full weight. Appliance is top heavy and tips easily when not completely installed. Keep doors closed until appliance is completely installed and secured per installation instructions.
Hinge Adjustment Installation (cont.) 6 5 Front of unit 10b 10a 2 2 3” 1 1 Remove four side screws and remove unit top. 3 Loosen the four hinge screws. Adjust door. Retighten four hinge screws. 8a 7 Place unit within 3” of being flush with cabinets. Note: To avoid cabinet damage, place cardboard between cabinets and unit. When moving unit, DO NOT crimp, kink or crush water supply line. Carefully move unit until semi flush with cabinet (depending on unit).
Hinge Adjustment (cont.) Door Stop Adjustment (Side-by-Side/All Refrigerator/All Freezer) 20 16 15 21 1 1 120˚ Screw Wall 110˚ 90˚ 3 2x4 Refrigerator Open refrigerator door so door stop and shoulder screw are accessible. Note: Shoulder screw should be in 110˚ door opening position. Attach positive secure self-tapping bolts to 2 x 4 using a 22” extension. Lift unit off rollers to desired height and level unit using a 5/16” head wrench. Note: DO NOT use an electric device.
Water Filter Installation (Side-by-Side with Dispenser) 24 Water Filter System Specification and Performance Data Sheet 25 This system has been tested according to NSF/ANSI 42/53 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration of less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42/53.
Final Installation Performance Checklist 29 28 Replace top air grille. Using an 8” magnetic nut driver, replace the two 1/4” screws. 30 31 Replace the center grille louver. Open door. The display should flash. 32 h Verify cabinet size. h Align/square door(s). h Verify electrical supply and water supply (if applicable). h Verify drain pan is properly installed and there are no leaks on water connection. h Install anti-tip device(s) and verify unit is secure. h Install kickplate.
Verify Operations Verify Operations Control Panels Control Panels Bottom-Mount All Refrigerator FREEZER ACTIVATE CONTROLS FRZ TEMP REF TEMP HIGHER CF MAX FRZ MAX REF LOWER FAST COOL SAB SHOW REFRIGERATOR DOOR OPEN POWER HIGH TEMP FAST COOL MAX REF MAX FRZ ALARM OFF DISPLAY OFF Side-by-Side FREEZER MAX FRZ MAX REF FAST COOL SAB SHOW ACTIVATE CONTROLS REF TEMP FREEZER HIGHER LOWER HIGHER LOWER CF MAX FRZ MAX REF FAST COOL SAB SHOW REFRIGERATOR DOOR OPEN POWER HIGH TEMP FAST CO
Service & Registration Notes Only authorized replacement parts may be used in performing service on the appliance. DO NOT repair or replace any part of the appliance unless specifically recommended in the manual. All other servicing should be referred to a qualified technician.
74 75
