Viking Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-VIKING1 (845-4641) or visit the Viking Web site at vikingrange.com UL F20734A EN 17-3336-01 C UL (120810) 15”W.
TABLE OF CONTENTS Warnings & Important Safety Instructions ______________________________________________________________________3 Dimensions (Professional) ____________________________________________________________________________________5 Dimensions (Designer) ______________________________________________________________________________________6 Dimensions (Custom Panel) __________________________________________________________________________________7 Specifications __________________________________
PROPER DISPOSAL (OF OLD REFRIGERATION UNIT) DIMENSIONS (PROFESSIONAL) DANGER RISK OF CHILD ENTRAPMENT Before You Throw Away Your Old Refrigeration Unit: • Take off the doors. • Leave the shelves in place so that children may not easily climb inside. IMPORTANT: Child entrapment and suffocation are not problems of the past. Junked or abandoned refrigeration units are still dangerous... even if they will sit for “just a few days.
DIMENSIONS (DESIGNER) DIMENSIONS (CUSTOM PANEL) Dimensions FGIM/FPIM w/ Designer door panel Dimensions FGIM/FPIM w/ Custom door panel 14 (37-7/8 .8 ” cm ) 30 (775/16 33 (86-7/8 .0 ” c .0 ” cm ) 14 (37-7/8 .8 ” cm ) 33 30 (775/16 (86-7/8 .0 ” mi cm) n. 34 to (88-7/8 .6 ” ma cm) x. .0 ” cm ) mi m) n. 34 to (88-7/8 .6 ” ma cm) x. /4”) 1 19 9 cm 4” -1/cm) 9 1 9 /4”) 3 2 m /4”) 3 22 8 cm . (48 . (48 2 .8 c (57 . (57 /4”) 1 5 m 2 .1 c 64 ( Door Swing Door Swing 14-3/4” (37.
15”W. Undercounter/Freestanding Ice Machine Description FGIM515 FPIM515 Overall width 14-7/8” (37.8 cm) Overall height 33-7/8” (86.0 cm) min. to 34-7/8” (88.6 cm) max. Overall depth from rear (without door panel) (with door panel) (with door handle) 15” (38.1 cm) 22” (55.9 cm) 22-3/4” (57.8 cm) 25-1/4” (64.1 cm) Cutout width 15” (38.1 cm) Cutout height 34-1/4” (86.4 cm) min. to 35-1/4” (89.5 cm) max. Cutout depth 24” (61.
SPECIFICATIONS DRAIN/ELECTRICAL LOCATION GENERAL INFORMATION AIR FLOW The machine takes in room temperature air at the lower right front and forces warm air out the lower left front. Restricting the airflow will adversely affect the ability of the ice machine to make ice. Filters and Treatment In general, it is always a good idea to filter the water. A water filter, if it is of the proper type, can remove taste and odors as well as particles.
INSTALLATION OVERVIEW Note: DO NOT build in so that the door is recessed. Door is meant to be flush with surronding cabinetry, but not recessed. 4. Subtract 1/8” or more for clearance space between top of door and bottom of countertop edge from cabinet opening. This is the maximum door length. 5. Cut panel to width 6. Cut panel to length (cabinet space - kickplate space - top clearance = length). 7. Determine top of panel. 8. Mark hole locations using drawing on the back of these instructions.
DOOR PANEL ATTACHMENT DOOR SWING CHANGE The door can be attached to open with hinges on the left or right using new brackets shipped loose in the ice bin. Retain all screws for re-use. Use Upper Hole at the Top Accessory Door Panel To change: 1. Remove inner screw holding each hinge to cabinet, loosen the outer screw. 2. Slide hinges to the side and remove door from cabinet. Remove outer screws loosened in step 1 from both hinge brackets. 3.
WATER & DRAIN INSTALLATION Gravity Drain Pump Model drain installation The recommended water supply tubing is 1/4” OD copper. Stainless steel flex or reinforced PVC tube may also be used. Install an easily accessible shut-off valve between the supply and the unit. This shut-off valve should not be installed behind the unit. Screw Note: DO NOT use self-piercing type valves. 1. Remove the front service access panel by removing the screw. 2.
SERVICE INFORMATION ELECTRICAL CONNECTION If service is required, call your dealer or authorized service agency. The name of the authorized service agency can be obtained from the dealer or distributor in your area. WARNING ELECTRICAL SHOCK HAZARD Failure to follow these instructions could result in fire or electrical shock. The ice machine is supplied with a power cord. DO NOT remove the grounding pin from the cord’s plug. DO NOT use extension cords. Follow all codes.
