User manual

Weld Control Selector Guide - Page 10
ESAB (Includes L-Tec & Linde)
The older Linde CV machines are connected as follows:
1. Connect the black and white contactor leads extending from the WC-1 Weld Control or the
Cobramatic Cabinet to the 6-Pin metal Pyle-National plug; black to pin 3 and white to pin 5.
Place WC-1 or Cobramatic in the 115VAC CONTACTOR position (See Appendix for changing
contactor).
2. Plug the 115VAC plug extending from the WC-1 or Cobramatic into a standard wall outlet or
cut off the plug and wire the black wire to pin 1, the white wire to pin 2 and the
green wire to pin 4.
3. Tape off WC-1 red and green leads and turn off Posa Start switch as
Posa Start is not used.
The newer ESAB/Linde/L-Tec CV machines are connected as follows:
1. Connect the black and white contactor leads extending from the WC-1 Weld Control or
Cobramatic Cabinet to the 7-Pin plastic AMP plug; black to pin 1 and white to pin 3. Place WC-
1 or Cobramatic in the CLOSING CONTACTS position (see Appendix for contactor information).
2. Plug the 115VAC plug extending from the WC-1 or Cobramatic into a standard wall outlet or
cut off the plug and wire the black wire to pin 1, the white wire to pin 2 and the green
wire to pin 4.
3. Tape off WC-1 red and green leads and turn off Posa Start switch
as Posa Start is not used.
Some ESAB/L-TEC CV/CC machines have 19 pin (J1) amphenols and are connected as follows:
1. Connect the black and white contactor leads extending from the
WC-1 or the Cobramatic to the 19 pin amphenol plug; black to pin
A and white to pin C. Place WC-1 or Cobramatic in the CLOSING
CONTACTS position (see Appendix for contactor information). Pins
U & V can also be used for contactor.
2. Plug the 115VAC plug extending from the WC-1 or Cobramatic into a
standard wall outlet or cut off the plug and wire the black wire to pin
A, the white wire to pin B and the green wire to pin D.
The MultiPower 460 units do not supply 115VAC at the 19-Pin.
3. Tape off WC-1 red and green leads and turn off Posa Start switch as Posa Start is not used. On
the Cobramatic System hook up the Posa-Start lead to the Power Supplies ARC GROUND and
use PosaStart when welding aluminum only.
E-5
Note: Use in CV-Mig mode and be
sure that nothing is plugged
into J2 (8-Pin).
A
B
C
D
E
H
J
K
L
M
N
P
R
S
T
U
V
F
G
B
L
A
C
K
W
H
IT
E
C
o
n
t
a
c
t
o
r
C
o
r
d
B
L
A
C
K
W
H
I
T
E
GR
E
E
N
115VAC
Leads
P/N 005-0614
Complete 8' cable with 19P Amphenol attached.
Easily connects to SVI 450 (115VAC on 19-Pin).
Pyle National “Triploc”
Male Plug AP-610
Housing APD-2004
7-Pin Amp Connector
L-Tec P/N AMP P/N
7-Pin Plug 674655 206226-1
Cord Clamp 674568 206138-1
Pins (4 req.) 674564 66255-1
E-6
19-Pin Amphenol
MK P/N’s Amphenol P/N’s
19-Pin Plug 153-0314 3106A22-14P
Cord Clamp 411-0035 3057-1012
Rubber Boot 301-0026 MS3420-12