Installation Guide 7 SERIES Integrated All Refrigerator VRI7240 / CVRI7240 FRI7240 / CFRI7240 MVRI7240 / CMVRI7240 Integrated All Freezer VFI7180 / CVFI7180/ VFI7240 / CVFI7240 FFI7180 / CFFI7180 / FFI7240 / CFFI7240 MVFI7180 / CMVFI7180 / MVFI7240 / CMVFI7240
Table of Contents Warnings and Important Information ________________________________________________________________________________ 3 Cutout Dimensions___________________________________________________________________________________________ 5 Specifications _______________________________________________________________________________________________ 6 Dimensions ________________________________________________________________________________________________ 8 Tipping Radius ___________________________
IMPORTANT – Please Read and Follow! • Make sure that incoming voltage is the same as unit rating. An electric rating plate specifying voltage, frequency, wattage, amperage, and phase is attached to the product. • To reduce the risk of fire, electrical shock, or injury to persons, installation work and electrical wiring must be done by a qualified technician in accordance with all applicable codes and standards, including fire-rated construction.
IMPORTANT – Please Read and Follow! A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local laws, or local ordinances. • The required use of a GFI is normally related to the location of a receptacle with respect to any significant sources of water or moisture. • Viking Range, LLC will NOT warranty any problems resulting from GFI outlets which are not installed properly or do not meet the requirements below.
Cutout Dimensions 25” ) cm (63.5 Can be lo cated on Electric Outlet Location either sid e 1 5-1/ (39.4 2” cm) 4-1/4 (10.8 ” cm) + leveli dimenng sion * (213 84” .4 ope cm) m ning in heig . ht 85 (216 -3/16” .3 ope cm) ma ning x. heig ht Water Line Entry Area *Cut o Wid ut th *Re 5/8 (1.6 ” cm) fer to S spe chart pecfic cific atio fo n Mod r els 1/2 (1.3 ” cm) 3” (7.6 6 (15.
Specifications (VRI/FRI/MVRI) Integrated All Refrigerator Description VRI MVRI 24" 24" Overall width 24" (61.0 cm) Overall height (from bottom) 83-15/16" (213.2 cm) min to 84-3/4" (215.7 cm) max Overall depth from rear 24" (61.0 cm) To front edge kickplate: 22-1/16” (56.0 cm) To front of door panel: 24-3/4” (62.9 cm) To front of handle endcap: 27-11/16" (70.3 cm) Cutout width To front of handle endcap: 27-5/16" (69.4 cm) 24" (61.0 cm) 24" (61.0 cm) Cutout height 84" (213.
Specifications (VFI/FFI/MVFI) Integrated All Freezer Description VFI Overall width Overall height (from bottom) MVFI 18" 24" 18" 24" 18" (45.7 cm) 24" (61.0 cm) 18" (45.7 cm) 24" (61.0 cm) 83-15/16" (213.2 cm) min to 84-3/4" (215.7 cm) max Overall depth from rear To front edge kickplate: 22-1/16” (56.0 cm) To front of door panel: 24” (61.0 cm) To front of handle endcap: 27-11/16" (70.3 cm) Cutout width 18" (45.7 cm) Cutout height To front of handle endcap: 27-5/16" (69.4 cm) 24" (61.
Dimensions (VRI/FRI/MVRI) 83-15/16” (213.2 cm) 4-1/16” (10.3 cm) 221 (56 /16” .0 c m) B A Model Dimension A Dimension B* VRIVFI 27-11/16" (70.3 cm) 24-3/4" (62.9 cm) FRI/FFI N/A 24" (61.0 cm) 27-5/16" (69.4 cm) 24-3/4" (62.
Door Swing / Tipping Radius 18" 24" A 19-1/16" (48.4 cm) 25-3/16" (64.0 cm) B 20-1/16" (51.0 cm) 26-1/16" (66.2 cm) C 4-1/2" (11.4 cm) 6-3/16" (15.7 cm) C A 127-3/16" (323.1 cm) B 1050 900 D 83-15/16" (213.2 cm) 111-3/16" (323.1 cm) D 87-3/4" (222.9 cm) 83-15/16" (213.2 cm) 9 18" 24" 83-3/4" (212.7 cm) 87-7/16" (222.
Anti-Tip Dimensions WARNING TIP OVER HAZARD Appliance is top heavy and tips easily when not completely installed. To avoid a hazard due to instability of the appliance, it must be installed according to the instructions including the anti-tip bracket C Anti-tip Bracket There are 12 hole locations on the anti-tip bracket. Of those 12, at least 4 places must be used. NOTE: Number of fasteners must be suitable for load in order to prevent tipping.
General Information Area Requirements Anti-Tip Requirements Verify the following: • Unit can fit into residence and can be moved around corners and through doorways. • Floors can support unit’s weight plus food weight (approximately 1200 pounds [540 kg] per unit). • Floors underneath refrigerator are level with surrounding finished floor. • Remove anything attached to rear or side walls that can obstruct unit installation. • Cutout dimensions are accurate. • Electrical outlet is in correct location.
General Information Water Supply Requirements (con't) Area Requirements • Most of the unit’s weight is at the top. Extra care is needed when moving the unit to prevent tipping. • DO NOT remove protective film until unit is in operating position. • All four leveling legs must contact the floor to support and stabilize the full weight. • DO NOT drop unit. • Remove exterior shipping materials prior to moving unit into home, except door latching device. • Use two or more people to move and install unit.
Moving Unit 1 A Remove shipping brackets from skid by removing four bolts (two on each side) with a 1/2” (1.3 cm) deep-well socket wench and a pair of pliers. Note: Tilting unit is not required to remove shipping brackets. Slip appliance dolly between unit and skid. Remove unit from skid. Note: Use excess packaging to protect decorative trim; also, verify that leveling legs are up (0” adjustment).
Optional Custom Front Panels - Dimensions Note: Overlay panel must be dry, solid, straight one-piece panels. The use of multiple panel pieces to achieve the dimensions is not recommended. Maximum panel weight: 18" door panel - 28 lbs (12.6 kg) 24" door panel - 41 lbs (18.5 kg) Custom Panel - hole locations 18” panel - 17-1/16” (43.3 cm) 5-1/16” (12.8 cm) 24” panel - 23-1/16” (58.6 cm) 5-1/16” (12.8 cm) 14-7/8” (37.8 cm) 25-7/8” (65.7 cm) 79-7/8” (202.9 cm) 35-7/8” (91.1 cm) 37-7/8” (96.
Optional Custom Front Panels - Install In order to access the mounting holes, unsnap panel trim on both sides of door.
Water Line Installation WARNING TIP OVER HAZARD Appliance is top heavy and tips easily when not completely installed. To avoid a hazard due to instability of the appliance, it must be installed according to the instructions including the anti-tip bracket Ensure you have approximately 6 ft. (1.8 m) of 1/4" (6 mm) copper tubing available at the right rear side of the refrigerator. Open door Remove the kickplate by removing the screws on each side.
Water Line Installation With the refrigerator in line with the cutout, but outside of the cabinetry, insert the copper tubing through the indicated hole. Push the copper tubing through the machine compartment until it comes out the front side of the refrigerator. Roll the refrigerator into place in the cabinet cutout. Coil the copper tubing in a vertical loop so that the end of the copper tube faces toward the rear of the refrigerator. Install nut and ferrule over end of copper tube.
Leveling Unit Once the unit is in position, height adjustment can be made from the front. Remove acess panel just below the water filter. Using a 5/16" hex drive, turn clockwise to raise the unit or counterclockwise to lower. Use the lowest torque setting when using a power drill. Do not turn the leveling legs by hand. When the unit is properly leveled, door/drawer adjustments are less likely to be necessary. IMPORTANT NOTE: Level the unit to the floor, not surrounding cabinetry.
Flush Mount Side Trim After the unit has been placed in the cutout, leveled and all connections completed, the unit will need to be fastened to the cabinetry. Open the door. Using the flat wood screws, fasten the unit to the cabinetry on both sides. NOTE: Only use the screws provided and use caution when installing the fastening screws to prevent scratching the frame. Use a 3" Phillips driver to prevent damage.
Door Stop Adjustment Your refrigerator is factory set at a 90o degree opening. The 90 degree door stop opening is shown in the illustration below with the long end of the door stop facing away from the door. To change to 105o door stop, locate the door stop on top of the door hinge. Remove the two screws and door stop. Rotate the door stop 180o degrees so that the shorter end faces away from the door. Replace door stop and screws.
Water Filter System Specification and Performance Data Sheet This system has been tested according to NSF/ANSI 42/53 for reduction of the substances listed below. The concentration of the indicated substances in water entering the system was reduced to a concentration of less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANSI 42/53.* (100% safety factors built-in for unmetered usage for health claims only.
Performance Checklist —Align/square door(s). —Verify drain pan is properly installed and there are no leaks on water connection. —Install kickplate. —Remove internal packaging and labels and wipe unit down. —Verify cabinet size. —Verify electrical supply and water supply (if applicable). —Install anti-tip device(s) and verify unit is secure. —Position unit in cutout, level at desired height and secure unit. —Plug-in unit and verify operation. —Connect water supply (if applicable).
Verify Operations 1. 2. When unit is first plugged in, the display will flash. "PL". Press the refrigerator select button twice to initiate display. Verify unit is not in Sabbath Mode. If in Sabbath Mode: A. The Sabbath Mode will disable the interior lights, display (except SAB indicator, temperature and compartment indicator) and alarm. If in Sabbath Mode, SAB will be lit. To exit the Sabbath Mode: 3. B. Press and hold SAB button for 3 seconds Verify unit is not in Showroom Mode.
Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-(845-4641) or visit our web site at vikingrange.
