Installation Guide Viking Range Corporation 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call 1-888-845-4641 Counter-Depth Freestanding French Door Bottom-Mount Refrigerator/Freezer or visit our web site in the US at www.vikingrange.com or in Canada at www.brigade.
Table of Contents Warnings & Important Information____________________________________________________________3 Proper Disposal ______________________________________________________________________________5 Dimensions (36” Bottom-Mount & French Door Bottom-Mount) ______________________________6 Specifications (36” Bottom-Mount & French Door Bottom-Mount) ____________________________7 Dimensions (36” French Door Bottom-Mount w/grille/side panels/top)________________________8 Specifications (36” French Door
IMPORTANT– Please Read and Follow Refrigerator Safety A GFI shall be used if required by NFPA-70 (National Electric Code), federal/state/local laws, or local ordinances. • The required use of a GFI is normally related to the location of a receptacle with respect to any significant sources of water or moisture. • Viking Range Corporation will NOT warranty any problems resulting from GFI outlets which are not installed properly or do not meet the requirements below.
Dimensions Specifications (Professional) French Door Bottom-Mount Description VCFF236 Overall width 35-5/8” (90.5 cm) Overall height To top of door: 71-7/8” (182.6 cm) To top of cabinet: 70-7/8” (180.0 cm) Overall depth from rear 44 71 (11 -1/4 2 .4 ” cm ) (18 -7/8 Back of refrigerator - 71-3/8" (181.3 cm) Front of refrigerator - 72-3/8" (183.8 cm) Cutout width 36” (91.4 cm) Cutout depth 24-1/2” (62.2 cm) Maximum amp usage Inlet water requirements 70 (18 -7/8 0. ” 0c m) 26 (67-1/2 .
Dimensions Specifications (with Grille/Side Panels/Top) (with Grille/Side Panels/Top) French Door Bottom-Mount w/ 35 sid (91-7/8 e .1 ” pa cm ne ) ls a cce Description VCFF236 with Top, Top Grille Kit & Side Panels Overall width Addition of side panel: 35-7/8” (91.1 cm) Overall height To top of cabinet with addition to top kit: 73-5/8" (187.0 cm) Overall depth from rear To front edge of cabinet: To front of door: To front of handle endcap: sso ry Cutout height 12 4 .4 ” cm ) 36” (91.
General Information General Information Clean Before Using Your refrigerator was packed carefully for shipment. Remove and discard all packaging and tape. DO NOT remove the model/serial number label. After you remove all of the packaging materials, clean the inside of your refrigerator before using it. See the cleaning instructions in “Use and Care Guide.” Important information to know about glass shelves and covers: DO NOT clean glass shelves or covers with warm water when they are cold.
General Information Water Supply Requirements A cold water supply with water pressure of between 35 and 120 psi (241 and 827 kPa) is required to operate the water dispenser and ice maker. If you have questions about your water pressure, call a licensed, qualified plumber. Reverse Osmosis Water Supply IMPORTANT: The pressure of the water supply coming out of a reverse osmosis system going to the water inlet valve of the refrigerator needs to be between 35 and 120 psi (241 and 827 kPa).
Door & Drawer Removal (cont.) Installation Replace Doors and Hinges Water Supply Requirements Connect the Water Supply Gather the required tools and parts before starting installation. Read and follow the instructions provided with any tools listed here. IMPORTANT: If you turn the refrigerator on before the water line is connected, turn the ice maker OFF.
Installation Leveling/Adjusting the Door Connect to Water Line (cont.) 6. Fasten the shutoff valve to the cold water pipe with the pipe clamp. Be sure the outlet end is solidly in the 1/4" drilled hole in the water pipe and that the washer is under the pipe clamp. Tighten the packing nut. Tighten the pipe clamp screws slowly and evenly so washer makes a watertight seal. DO NOT overtighten or you may crush the copper tubing. 7. Slip the compression sleeve and compression nut on the copper tubing as shown.
Complete the Installation Service & Registration Final Steps Only authorized replacement parts may be used in performing service on the appliance. All servicing should be referred to a qualified technician. 1. Plug into a grounded 3 prong outlet. 2. Return all removable parts to doors and drawer and food to refrigerator and freezer.
