Warnings & Important Information 34 VWH/CVWH 10” Wall Hoods w/Standard Ventilator 30", & 36" Dimensions & Specifications Clearance Dimensions Interior Ventilator Dimensions VWH/CVWH 18“H. 24"Deep Wall Hoods 307, 36", 42, 48", & 60" Dimensions & Specifications ~ o u; Clearance Dimensions Interior Ventilator Dimensions Exterior Ventilator Dimensions VWHO/CVWHO 18"H.
NOTE: if installing hood with warming shelf panel, install warming shelf panel first. IMPORTANT — PLEASE READ AND FOLLOW « Before beginning, pleads read theses instructions completely and carefully. « Do not remove permanently affixed labels, wakings, or plates from the product. This may void the warranty. + Please observe all local and national codes and ordinances. If no local codes are applicable, wire in accordance with the National Electrical Code, EXPANSION 70-latest edition.
WARNING To reduce the risk of injury to persons in the scent of a range tap grass fire, observe the following. {Based on “Kitchen Firewater Tips,” published by PAN) 1. SMOTHER FLAMES with a close fitted lid, cookie sheet, or metal tray, then tum off the burner. BE CAREFUL TO PREVENT BURNS. If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT. 2. NEVER PICK UP A FLAMING PAN. You may be burned. 3.
(VWH Wall Hoods w/Standard Ventilator 30", & 36") A {Hood with) 911 e} A {Flood with] NOTE: Optional duct cover sold separately. 0 6 (75.9 cm) (91.1 cm) 12* (30.5 ¢m) 12" (30.5 460 CFM Standard 7" (17.8 em) S6A * Disregard when using recirculating kits. 460 CFM blower is shipped with hood.
(VWH/CVWH Wall Hoods w/Standard Ventilator) * NOTE: When installing with a 24" high-shelf, the 277 (68.6 cm) max. dimensions must be used.
(VWH/CVWH Wall Hoods w/Standard Ventilator) Top View I0W, | 29778 759 em) WW B Guam 1/2° AW |54 (133em 0. | 81/4" (209 {10.2 electrical WW. 1L/ 303 e @8em) hookup 30°W. | 1415/16° (37.9 cm) " 36"W. | (65.
(VWH/CVWH 18"H. 24" Deep Wall Hoods 30", 36", 42", 48", & 60") A W W78 (F62em) 38'W | ISR (Flies) AW | (1084 am) AW | 47778 (1218 (1521 em) NOTE: Optional duct cover sold separately. (91.1 em) (106.4 ¢m) 12" (30.5 em) 12" (30.5 VINSON/ VINSON/ INVENTIVE/ 600/1200 600/1200 1200 DEVI/ DEVOID/ DEVIOUS/ 1200% 1200% 1200% DIL1200 DILLARD DIL1200 710" 77107 7N em} | em} | am) 10" (24.5 cm) 47 Watts 5372 (121.6 cm) DEV1200%/ 1500+ DIL1200 10" (25.4 em} 108 9.
(VWH/CVWH 18"H. Wall Hoods) 7* (178 cm) dia, duct location Top View A 8 30TH (37.9 om) W 5.9 am} 36w 1715718 (45.6 em} 38°W 35778 (911 em} AW | (532 em) AW | S17/8 (Beseem) 48w a8t W A77/8" (1216 em) 0" W (5.0 em) ST W 597/8° (1521 em 300 or 600 CFM Interior Ventilator Installation for all Wall Hoods 17516 454 45°W | 2315/16" (608 cm) W | 298 (a0 ) Top View R S Sz fa gem W W 5 (5.9 EHE Gl am J1/8° (106 (25.
(VWH/CVWH 18"H. Wall Hoods) Top View A W ane @i 36°W | 171516" Bahama) 2 W | 201516 Eczema) AW 4178 (106Aem wwW e amazing WW | 2516 (ham) 7 WW_ (25.4 e} dia. duct location 900 or 1200 CFM Exterior or In-Line Ventilator Installation for all Wall Hoods Top View 37.3 em) ! i 29-778° {75.% cm) %W | 171518 @58 am) 515/16° BEANS Sudan |[@W (60.8 {1216 am} W | 29-15016" (6.0 am) / 60°W | 597/8° (1521 em) 10° (25.4 am) dia.
(VWHO/CVWHO 18"H. Outdoor Wall Hoods 36", 48", & 60") Seal joints with silicone. Provided on “T° Series only. . A 38°W 37T Diem) AW 427/8 (1216 em) W 5978 (1521 am) NOTE: Optional duct cover sold separately. (91.1 em) 2 2 VINV1200* DILLARD 477/8" (121.6 cm} 12" (30.5 em) 12" (30.5 cm) 3 3 VINV1200% DIL1200 10" {25.4 cm) 107 (25.4 cm) 14 102 47 Waits ) (152.
(VWHO/CVWHO 18”H. Outdoor Wall Hoods) Note: Outdoor Models must be installed in a covered, non-enclosed area, and should be protected from the elements as much as possible. The bottom of the hoed should be 30" (76.2 cm) te 36" {91.4 cm) above the grill surface. The hood should be installed (11.4 cm} plus the distance between the back trim and surface from the back wall. {Note: There is a 3" minimum clearance from the back trim to non-combustible surfaces, and a 24" minimum te combustible surfaces.
(VCWH/CVCWH Chimney Wall Hoods 30", 36, 42", 48", 54", & 60") A (Duct width) TWO, 127 (305 em) 36°W. | 12" (305 em) 42" | 127 (305 am) 48"W. | 187 {457 em} 0°W. | 24" (810 em) S6"W. | 24" (61.0cm) B (Hood width) I0W. 762 em) 36°W. | (911 em) 42°W, (1064 em) 48°W. (1218 em) W, (152,1 am} TWAS. (167.3 am) NOTE; Optional duct cover sold separately. 127 (305 cm} | 12* (30.5 em} | 12" (30.5 cm) | 18" (45.7 cm) | 24" (61.0 cm) 127 (30.5 cm) 12" (30.5 em} to 247 (61.
(VCWH/CVCWH Chimney Wall Hoods) Top View 120¢ power 12 e PRy Moose | 412~ TARE I | a52em) y |7 ¢ 1745/16" (45,6 em) f ] & ; N (3.8 (155 (1068 om) ZIu 300 or 600 CFM Interior Ventilator Installation for 307, 36", & 42" models Top View 120V 14/27 power @.8em} _supply 52y 2945/16" (6.8 emf 1-142° 321BAE” (337 ey {3.8 48"W. (1216 cm} W, {1521 dia.
(VCWH/CVCWH Chi money Wall Hoods) Top View 12V 12¢ parer (30.5 em) 1-172" -3 A ///1 @Nisan =iy } 14727 2| 201518 (532 em)) . @8em & — W TEE (1064 o} :‘gdflféxgdm. \ 900 or 1200 CFM Exterior or In-Line Ventilator Installation for 30”7, 36", & 42" models Top View 48°W. {121.6 ) 10° (25.& cm) dia.
(VCIH/CVCIH Chimney Island Hoods 36", 42", 54", & 66") A 36" W fie F (305 em) 42°W f17° (305 em) 54"W 18" (45.7 cm) &6°W P& {700 (305 on 427 (e:r.o (91.4 42°W (1064 em) 54"W 537/8° (1368 cm) 66"W (167.3em) NOTE: Optional duct cover sold separately. 12* (30.5 em) VINSON DEVI00/1200* DIL1200 127 (30.5 em) 18" (45.7 cm) 12" (30.5 cm) 12” (30.5 cm} or 24" {61.0 cm) or 36" {91.4 VINSON VINV1200* DiL1200 DIL1200 107 (25.4 cm) 52/82 7483755 3957 47 Watts 24" (70.
(VCIH/CVCIH Chimney Island Hoods) Top View A 36W. (45.6 ey 4 (53.2 o} 8 38°W, 911 com} 2, {106.8 (178 om) dia. N duct location 600 CFM Interior Ventilator Installation for all Chimney Island Hoods Top View c 261518 SEAS (837 53-778” (1368 om} S"W. (1673 ape (25.
(VCIH/CVCIH Chimney Island Hoods) Top View 12" 11/8° (30.5 em) (2.9 cm) e / 120¥ A “power W, [ 75116 5B am) supply 11787 (seemly (1068 107 (25.4 cm) dim. >\ o duct location -8 900 or 1200 CFM Exterior or In-Line Ventilator Installation for all Chimney Island Hoods Top View 120V A _ power W, | 261516° (GBA cmy supply 86°W. | (837 om) —{2.9 em} & S4W,_ [ 539/% (1368 em) 66°W, | 65978 (1673 (258 (61.
(VB Wall Custom Ventilator System 36", 42", 48", & 60") *For best results, center the unit over the numbers of the cooking product {front to back; right to left). [ S } Make sure the back wall of the custom hood canopy is flush with the cutout o the ventilator system may be mounted as shown on page 25, Bottom Cutout Dimensions Nal ©0gs LN GOy (84.9 cm) B (Hood Depth) (54.5 em) (100.2 cm) (54.5 cm) (115.4 cm) (54.5 cm) (145.9 cm) (54.5 VINEYARD/ 600/1200% DESTROY/ 1200 DiL1200 7°110" cm}| (25.
8ol 258 < L8 T ZE®§ = 035< a GEESE . Oreg Custom Hood Canopy system inside of the custom hood canopy and center it front to back and left to right. fasten ventilator system hood canopy with the screws provided.
‘% 207/8pe g | s5/8° (1.6 em) {85.8 cm} For 900, 1200 or 1500 CFM Exterior or In-Line Ventilator Installation 10" (25.4 dia. duct location \ (1.6 cm) e 900 or 1200 CFM Exterior or In-Line Ventilator Installation 36", 42" W. Models 5. )—i; (1.6 cm} 78" (2.2 em} 17104 438 cmy {55.8 cm) For 300, 600 or 1200 CFM Interior Ventilator Installation 7178 un/) / dia. duct location == 5/8" {1.6 em) bt Ventilator Installation 36", 42" W. Models (87.0 cm) 36" W, (43.5 cm) 42" W, (102.2 cm) 42" W, (51.
dia, duct Location \ || 5/8" (1.6 cm} C— 1200 or 1500 CFM Exterior or In-Line Ventilator Installation 48", 60" W, Models 190" {25.4 5/8" (1.6 cm} C 1200 CFM Interior Ventilator Installation 36", 42", 48", 60" W. Models (87.0 cm) 36" W. {43.5 cm) 427 W. 40-174" (102.2 cm) 42" W. (51.1 em} 48" W. 46-174" (117.5 cm) 48" W. (58.7 cm} 607 W, (148.0 cm) 60" W, (74.
Proper installation of ducting is extremely important to ensure maximum performance from any ventilation product. ® All Cf Ms are based on tests at 0.1 static pressure: without applying static pressure, CFM would be greatly overstated. * Straight runs and gradual tums are best; for example, each 90° elbow is equivalent to 5-10 feet cm) of straight run. * Over use flexible duct; it creates back pressure/air turbulence and greatly reduces performance.
Attach transition to damper. Seal with aluminum tape. Check damper for unrestricted movement, adjust i necessary. Flip hood over and remove electrical box cover. Slide duct over transition and tape around joint. Insert 6" of electrical wiring through the top of vent hood and secure using wiring restrain.
CAUTION: Secure cant hood to wall using CAUTION: If not using a duct cover, using screws provided. Use additional mounting craws and wall provided, make sure top mounting screws are secured anchors, if necessary. into offsite or cabinet framing. Use additional mounting screws, if necessary. Connect black to black, white to whits, and the Replace electrical box cover. Make connection to greenback wire under the green screw. brisker box.
N Nl Ny Slide the duct cover in place and fasten from inside canopy using the sheet metal screws provided. Measures distance from ceiling to canopy. (VWH/CVWH Wall Hoods w/Recirculating Kit) Installation Tum recirculating unit upside down. Place vent hood upside down on recirculating unit. 30 Remove damper and discard with transition.
pods w/Recirculating o N/ Attach with scows. Attach with screws and lack washers provided. Remove electrical box cover. screws are secured into framing. Use additional top of vent hood and secure. Refer to local codes. Flip hood over. Insert 67 of electrical wi mounting screws and wall anchors, if necessary.
w/Recirculating Connect black to black, white to whits, and the Replace electrical box cover. Make connection to green/bare wire under the green craw. breaker box, NOTE: Housing wiring must be properly installed for wiring to be correct when wiring unit. Slide filter front over front lip. Push filter rear up, then slide back over rear lip. Slide spacer front over front lip. Push spacer rear up, Slide filter front over front lip. Push filter rear up, then then slide back aver rear lip.
L4k ve o DMD wind spiel VWH/CVWH only Measure down (4.6 cm) from desired height of hood and secure x 3/4" wood strip (provided locally) to wall using screws provided. chimney vva 00 VWH/CVWH only Use additional mounting screws to secure hood to wood strip. ‘CAUTION: Secure vent hood to wall using screws provided. Use additional mounting screws and wall anchors, if necessary. CAUTION: If not using a duct cover, using screws.
Measure distance from ceiling to canopy. Slide the duct cover in place and fasten from inside canape using the sheet metal screws provided. To install ventilation kit refer to ventilation kit installation instructions.
Tape to avoid scratching. Measure distance from ceiling te canopy. Place duct cover top inside duct cover base and lower unit Slice the duct cover in place and fasten from side desired height is found. Mark height. Use the retaining canopy using the shes metal screws provided. nuts and bolts to fasten in place and remove tape.
Check framing where cutout will be. Cut appropriate size hols in ceiling. Either 7 or 10* NOTE: 200 Ib. limit. depending on your specific unit and ventilator kit. Amounting options: Using duct cover with c:eilinshmounting racket. (Option A ACTH only) Using threaded rad for additional support, [Option 8) Attaching hood directly to sol fit or dust cover. {kip to step 3} Attach duct cover to ceiling. The ceiling bracket can be Additional support option.
Run duct work down to bottom edge of duct Attach canopy to duct softcover. Seal top of hood to softcover and secure in place. Make sure the duct duct with aluminum tape. does not stick down past the cover. Slide filter front over front lip. Push filter rear up, then slice back over rear lip. slide back over rear lip. To install ventilation kit refer to ventilation kit installation instructions.
If service is required, call your dealer or authorized service agency. The name of the authorized service agency can be obtained from the dealer or distributor in your area. Have the following information readily available. * Model number * Serial number * Date purchased * Name of dealer from whom purchased Clearly describe the problem that you are having.
Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA (662) 455-1200 For product information, call or visit our web site at vikingrange.com in the US brigade.