Table of Contents Warnings and Important Information __ 3 Professional Bottom-Freezer Dimensions & Specifications 7 Cutout Dimensions 8 Anti-Tip Dimensions (367) Cabinet Information (Professional) _ Cabinet Information {Professional with flush mount trim) 11 Custom Side Panel Dimensions (Professional} 12 Custom Side Panel Dimensions (Professional with flush mount trim) 13 General Information 14 Unpacking & Moving 16 Flush Mount Side Trim Installation 17 Installation Hinge Adjustment Kick plate Installation
IMPORTANT — Please Read and Follow! * Make sure that incoming vantage is the same as unit rating. An electric rating plate specifying voltage, frequency, wattage, amperage, and phase is attached o the product. s To reduce the risk of fire, electrical shock, of injury te persons, installation work and electrical wiring must be done by 8 qualified technician in accordance with all applicable codes and standards, including fora-rated construction.
IMPORTANT Please Read and Follow! A GFi shall be used i required by PAN-70 (National Electric Code), federal/state/local * The required use normally related to the location of a receptacle with respect to any significant sources of water or moisture. ® Viking Range, LLC will NOT warranty any problems resulting from GF} outsets which are not installed properly or do not meet the requirements below.
IMPORTANT Please Read and Follow! It is your responsibility to: e comply with installation specifications and dimensions. properly install unit, remove any moldings or decorative panels that prevent the unit from being serviced. make sure that you have these materials {not provided with your unit}, which are necessary for proper installation: = 1/4” {6 mm) caper tubing with shutoff naive (7.
Specifications (otiose-Freezen 36” (91.5 em) {210.2 cm) min. o (213.5 om) max, Te front edge of side trim: (56.4 cm} To front of top grille: 24% (61.0 am) To front of handle endear: (67.3 em) {90.5 em) min. to (90.8 em) max. (210.5 em) min. to (213.5 am) max. 247 (61.0 cm) min. 115 volt, 80 Hz, 15 amp dedicated circuit; 3-wire cord with grounded 3-prong plug attached to product 9.9 amps 144" copper tubing inlet waterline; minimum 20 psi; maximum 120 psi 15.3 cu. 1. (434 tiers) 5.1 eu. ft. {145 liters) 20.
Anti-Tip Dimensions bottom-Freezen 36" Bottom-Freezer Bottom of anti-tsp board is (9.8 cm) below opening height. NOTE: Top of unit must b placed firmly under anti-tip board. Anti-Tip Location . T “"Fwo 2°x 4 Mounting Boards ™ 3 7.6 ard x 327 (8.9 o) Bursae NOTE: #f unit is installed deeper than (61.0 cm), then shim behind the mounting boards by the difference. \\ One 2% 4° Mounting Board 3" (7.6 em} x NOTE: if unit is instated draper than (81,0 am), than shim behind the taunting ‘buzzards by the difference.
Cabinet Information professional Professional models fit "semi-flush” in standard 24" {61.0 cm) deep cabinet openings. The door face protrudes (4.4 cm} from the cabinet face. The handle protrudes an additional {64 om} into the room. 4.6 em) Spica if 24" standard dtzbk;afl Is e 3/4° {1.9 em} Full End A (4.5 cm} Space if 247 standard cabinet depth is sad 3/47 (3.
Cabinet Information (Professional with Flush Mount Trim) Professional models with flush mount trim fit flush in standard 247 (61.0 om) deep cabinet openings with no protrusion into the rem except the handier protrudes (6.4 cm) into the room.
Custom Side Panel Dimensions {Professional) ) Back filler {1.9em} A panel End pane! 4 | \ ‘213% 5 w:’q adage iy 3% ., gt g A/// Optional kick plate 1 Ne sch, discussant Lol 7 terminator by cablecasts @ * Depending on how high leveling fest are raised, and cabinet enclosure height.
Custom Side Panel Dimensions {Professional with Flush Mount Trim} & B Z{‘u g Q“)M . Loy kick pt v e e harebrained by cabinets 2 e * Depending on how high leveling feet are raised, and cabinet enclosure height.
General Information Area Requirements Verify the following: © Unit can fit into residence and can be maced around comers and through doorways. © Floors can support unit’s weight plus food weight {approximately 1200 pounds {540 kgl par unit). Floors underneath refrigerator are level with surrounding finished floor. ® Rear wall is solid and is able to support two horizontally mounted 2 x 4s {included) bolted to two wall studs.
General Information ‘Water Supply Requirements A WARNING Ta avoid serious iciness or dash, DO NOT wes ult whirs wale is misanthropically unsafe ar of unknown @ity without! squatted disinfection before or after tha system. Systems codifier for vet reduction may be used on disinfectant war that may contain Hitlers cysts.
General Information Area Requirements * Maoist of the unit’s weight is at the top. Extra cars is needed when moving the unit to prevent tipping. * DO NOT remove protective film until unit is in operating position. » Al four labeling lags must contact the floor to support and stabilize the full weight. = DO NOT drop unit. * Remove exterior shipping materials prior o moving unit into home, except door latching devices. ® Uss two or more people to move and install unit.
Flush Mount Side Trim Installation (Sold Separately) Mote: if the unit is to be installed flush with Step 3 Align the top of the flush mount the cabinets, the flush mount side trim must sidle trim with the top of the unit's machine be installed first. If not, skip to "installation”. compartment.
Hinge Adjustment Remove four side screws and remove unit top. Loosen the four hinge screws. Adjust door. Re tighten four hinge screws. Refrigerator Attach one 2x 4 to wall stud (refer to dimensions page notion. Refrigerator f needed, depending on cabinet and depth, Plug in parer cord to verify aeration. attach second 2 x4 to first 25 4. Note: Make sirs power switch i in the *On* Position.
Hinge Adjustment (cont) Claps unit within 3% {7.6 cm) of being flush wih cabinets. Note: To avoid cabinet damages, place cardboard between cabinets and unit When moving unit, B0 NOT crimp, kink or crush water supply fine. Carefully move unit until semi flush with cabinet (depending on unit). Pull supply tubing forward under unit. Flush warts ins ky running tees quarts of water Note: DO NOT use plastic water lines. into a bucket. Turn water off. Connect supply tube 1o water valve using— a 1/2” ranch.
Hinge Adjustment (cont) Refrigerator Lift unit off rollers to desired height and elev! unit using Reinstall handle side door wim 2 5716” head wrench, NOTE: DO NOT use an electric snd door trim screws, device, Over tightening can cause damage.
Kick plate Installation Using a Philips screwdriver, attach the and insert screws, kick plate to the unit and adjust to desired height, Door Stop Adjustment Bosom-Freezer) Open refrigerator door o door spat and shoulder Remove shoulder screw and place in screw are accessible. Meta: Shoulder screw should be 90° o 120° position. in 110° doer opening position.
Water Filter System Specification and Performance Data Sheet This system has been tested according to NSF/ANS! 42/53 for reduction of the substances /sited below. The concentration of the indicated substances in water entering the system was reduced o a concentration of less than or equal to the permissible limit for water leaving the system, as specified in NSF/ANS! 42/53.* {100% safety factors built-in for undeterred usage for health claims ably) 20 mg/l 2.0 mg/l + 10% 0.05 mg/L.
Final Installation Using s 8 (20.3 cm) magnetize nut drives replace the two 1/4" {0.6 cm) screws. Open road. The display should flash. Cross “ACTIVATE CONTROLS® pad znd clods door. Mote: There is » 6 minute delay before the unit starts.
Performance Checklist —Verify cabinet size, —Squalidness door's, —Verify electrical supply and water —Verify drain pan is properly installed supply (f applicable). and there are no leaks on water connection. —Install anti-tip device(s) and verify unit is secure. —Install kick plate. Position unit in cutout, elev! at desired —Remove internal packaging and labels height and secures unit. and wipe unit down. —Plug-in unit and verify operation. installer’s information: —Cannot water supply (f applicable).
Verify Operations Control Panels H Bottom Freezer 1. Press “ACTIVATE CONTROLS” pad. 2. Verify unit is not in Sabbath Mode. if in Sabbath Mode: A. The Sabbath Mods will disable the interior lights, display {except SAB indicator, temperature and compartment indicator) and alarm. To taxi the Sabbath Mode: B. Press and hold “ACTIVATE CONTROLS" and then "DISPLAY OFF” for 3 seconds. {The control will esp three times to alert the user the Sabbath Mode has been exited) 3. Verify unit is not in Showroom Mode.
Service & Registration if service is required, call your authorized service agency. Have the following information readily available. * Model number Serial number © Date purchased = Name of dealer from whom purchased Clearly describe the problem that you are having.
Viking Range, LLC 111 Front Street Green woad, Mississippi 38930 USA (662) 455-1200 For product information, call or visit our web site at vikingrange.com in the US or brigade.ca in Canada r 0y gm0\ @ e ot F21417AEN {120115}