Warnings & Important Information 2 Professional Dimensions & Specifications (30" & 36") 4 Dimensions & Specifications (30" & 36" with flush mount trim) & Cutout Dimensions (30”) 8 Anti-Tip Dimensions (30") 9 Cutout Dimensions (36") 10 Anti-Tip Dimensions (36") Dimensions & Specifications (Dual 30"/ Dual 30" & 36") Dimensions & Specifications (Dual 30"/ Dual 30" & 36" with flush mount trim) Cutout Dimensions (Dual 30") Anti-Tip Dimensions (Dual 30%) 21 Cutout Dimensions (Dual 30" & 36") Anti-Tip Dimensions (
* Make sure that incoming voltage is the same as unit rating. An electric rating plate specifying voltage, frequency, wattage, amperage, and phase is attached to the product. » To reduce the risk of fire, electric shock, or injury to persons, installation work and electrical wiring must be done by qualified people in accordance with all applicable codes and standards, including fire-rated construction.
30" (76.2 cm) (210.2 min. to (213.5 max. To front edge of side trim: (56.4 cm} To front of top grille: 24" (61.0 cm) To front of handle end cap: (67.3 cm) (75.2 cm} min. to (75.6 max. (210.5 cm) min. to (213.5 cm) max. 24" {61.0 cm} min. 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with rounded lug attached to uct copper tubing inlet waterline; minimum 20 psi; maximum 120 NA 15.9 cu. ft. (450 liters) 17.8 cu. ft. (504 liters) 550 Ibs. {247.5 kg) 525 Ibs. {236.3 kg) 36" (915 em) (210.2 cm) min.
30" All Refrigerator/All Freezer with Flush Mount Trim e Tem) § 36" All Refrigerator/All Freezer with Flush Mount Trim 75_1 3 RESAT 2,9%) = 824, Riga fare ‘213‘52\) ax, Note: Flush Mount Trim (PBIRFTKSS) purchased separately.
30" (76.2 cm) (210.2 cm) min. to (213.5 em} max. To front edge of side trim: (5.4 cm) To front of top grille: 24" (61.0 cm) To front of handle endear: (67.3 em) 30" 74.9 cm) (210.5 cm) min. to (213.5 cm) max. 24" {61.0 cm} min. 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with rounded lyg attached to uct copper tubing inlet waterline; minimum 20 psi; NA maximum 120 15.9 cu. ft. (450 liters) 17.8 cu. ft. (504 liters) 550 Ibs. (247.5 kg) 525 Ibs. (236.3 kg) 36" (91.5 em) (210.2 cm) min. to (213.
30" All Refrigerator/All Freezer | flsiqqm o — 5 Electric Outlet Location Water Line Entry Area Nate: Shown for All Freezer Only
30" All Refrigerator/All Freezer Anti-Tip Location T 2°x 4% mounting boards . 37 (7.6 em) X 31/2" (8.9 em) < NOTE: ¥ unit is installed preside than N e {51.0 shim behind the mounting / < oars by the difference. " Tone's" mourning board (3.8 om) x 8.9 em} Bottom of anti-tip board is (7.8 om) below opening height. \ Nat: Top of unit must be placed finely under anti-tip board, NOTE: Hun s instated draper than N 24 (61.0 cm}, then shim behind the mounting /! board by the difference. / .
Dual 36" All Refrigerator/All Freezer* 5., tog S 16e ‘ Rio ) ! Wiy, ! to : B4..
(152.4 cm) 66" (167.6 cm) 727 (182.9 cm) {210.2 cm) min, to (213.5 cm) max. To front edge of side trim: (56.4 em) To front of top grille: 24" (61.0 cm) To front of handle end cap: (67.3 em) {151.4 cm) (166.7 cm) (181.9 cm) (210.5 em) min. to (213.5 cm) max. 24" (61.0 cm) min. (2) 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with rounded lug attached to uct 30" Freezer 9.1 amps per unit 30" Refrigerator 5.7 amps per unit 36" Freezer 9.
Dual 30" All Refrigerator/All Freezer with Flush Mount Trim* Note: Flush Mount Trim Kit (PBIRFTK) purchased separately 197300 91 '3“? 95 (zsg.nqzn') 5.
Dual 30" & 36" All Refrigerator/All Freezer with Flush Mount Trim* Note: Flush Mount Trim Kit (PBIRFTK) purchased separately *Shown with optional one-piece grille kit 17
Dual 36" All Refrigerator/All Freezer with Flush Mount Trim* Note: Flush Mount Trim Kit (PBIRFTK) purchased separately @1 m‘) 75y fist g o) *Shown with optional one-piece grille kit (purchased separately) 18
(152.4 cm) 66" (167.6 cm) 727 (182.9 cm) {210.2 cm) min, to (213.5 cm) max. To front edge of side trim: (59.4 em) To front of top grille: 24" (61.0 cm) To front of handle end cap: (67.3 em) 60" (152.4 cm) 667 (167.6 cm) 727 (182.9 cm) (210.5 em) min. to (213.5 cm) max. 24" (61.0 cm) min. (2) 115 volt, 60 Hz, 15 amp dedicated circuit; 3-wire cord with rounded lug attached to uct 30" Freezer 9.1 amps per unit 30" Refrigerator 5.7 amps per unit 36" Freezer 9.
Dual 30" All Refrigerator/All Freezer Electric Outlet Location 186.4 E Sigh i Water Line Entry Area Note: Cutout opening shown with All Freezer model an deft. b Reverse water line sate if All Freezer model s an right.
Dual 30" All Refrigerator/All Freezer { N, Bottom of anti-tip board is (9.8 cm) below opening height. Note: Top of unit must ba placed firmly under anti-tip board. 21 Roves 2°x 47 mounting boards per unit \Q" (61.8 cm), then shim behind the ant-tip . N, . 247 [64.0 cad, then shim behind the antipasti @7 om) Pints: f unit is installed deeper than bracket by the difference. e Ona 2°x 4" mounting board per unit (3.8 em) x (8.9 em) Note: # unit Is installed deeper than bracket by the difference.
I Dual 30" & 36" All Refrigerator/All Freezer Electric Outset Location Water Line Entry Area Note: Cutouts opening shown with All Freezer modal on toff. Reverse water line entry if All Freezer model is on zit.
Dual 30” & 36" All Refrigerator/All Freezer Anti-Tip Location Toto 2°% 4" mourning boards per unit 3" (7.6 con) 1.3 1/2" iy, \ Note: If unit is installed deeper than (67.0 cml, then shim behind the mounting P boar N\, towards by the difference. / One 27 4" mounting board per unit (3.8 em} x (8.9 em} N\ Bottom of anti-tip board is (9.8 e} below opening height. Note: Top of unit must be placed firmly under smite-tip board. Nate: Dickensian shown for 36° AF/AR model on the lat.
Dual 36" All Refrigerator/All Freezer Electric Cutlet Location Water Line Entry Area Riot: Cutout opening shown with All Freezer mods! on left.
Dual 36" All Refrigerator/All Freezer / Two 2°x 4" mounting boards per unit "\ 37 (7.6 emd x (8.9 om} Note: i unit is installed draper than 247 {61.8 e, then shim behind the mounting Boards by the difference. o o N One 2x 4 mounting board per unit ™\ (3.8 om) x (8.9 cm) « Bottom of anti-tip board iz (9.8 cm) below spending height.
Professional models fit “semi-flush” in standard 24" (61.0 cm) deep cabinet openings. The door face protrudes (4.4 cm) from the cabinet face. The handle protrudes an additional (6.4 cm) into the room. Top View A /T a-1st 4.6 crn) / Space ¥ 247 (61.0 om) standard cabinet depth is used . 1.0 | 3747 Sl i dash | (1.8 o} | Full end pans| IJ / / Contention overhang 8.6 em} Space i 24" (61.
Professional models fit “semi-flush” in standard 24" (61.0 cm) deep cabinet openings. The door face protrudes (4.4 cm) from the cabinet face. The handle protrudes an additional (6.4 cm) into the room. Top Vie / A 7 @6em / Space if 24° (61.0 om) standard cabinet depth is used 63,0 cn) /4" Standard cabinet depth {1.9 em) Full end anal Partial overlay J cabinet door 13/6" e (8.
Models with flush mount trim fit flush in standard 24" (61.0 cm) esp cabinet openings with no protrusion into the room except the handle protrudes (6.4 cm) into the room. Top View 257 (62,5 em) y cabinet depth \ s sad (EMT) satin ] Full and pans| depth | / (1.
Models with flush mount trim fit flush in standard 24” (61.0 cm) deep cabinet openings with no protrusion into the room except the handle protrudes (6.4 cm) into the room. Top View Overlapping cabinet doors space i 247 (61,0 em} standard cabinet depth Is used {629 o | (1.9 em) Full end anal Top View Flush mount cabinet doors 257635 cm) cabinet doth s wed 28 \ (83.
/ 37167 AN / PSm 374" N /! Back filer (1.9 em} \ /’ panel Enid pans ‘21‘; e Ry '145 “'h) n, L) Optional bookplate note i P Dimensions determined by cabinets L g * Depending on how high leveling feet are raised, and cabinet enclosure height.
(With Flush Mount Trim) \ £ ~ & dag M ™ M, w}:: o Optional kick plats notch Dimensions determined by chlorinates | 1‘4‘) | * Depending on how high leveling feet are raised, and cabinet enclosure height.
Area Requirements Verify the following: * Unit can fit into residence and can be moved around corners and through doorways. * Floors can support unit's weight plus food weight (approximately 1200 pounds [540 kgl per unit). * Floors underneath appliance are level with surrounding finished floor. ® Rear wall is solid and is able to support two horizontally mounted 2 X 4s (included) bolted to two wall studs. The 2 X 4 board bolt heads must be flush with prevent obstruction.
Water Supply Requirements (All Freezer q WARNING To avoid serious oiliness or death, do not uss unit where water is micro biologically unsafe or of unknown quality without adequate disinfection before or after tha system. Systems certified for cyst reduction may be used on disinfected water that may contain filterable cysts. The contaminants or other substances removed or reduced by this water treatment system are not necessarily in you water. Use only 1/4” (6 mm} copper tubing for water line.
* Most of the unit's weight is at the top. Extra care is needed when moving the unit to prevent tipping. * Do Not remove protective film until unit is in operating position. * All four leveling legs must contact the floor to support and stabilize the full weight. # Do not drop unit, * Remove exterior shipping materials prior to moving unit into home, * Use two or more people to move and install unit. Failure to follow this instruction can result in back or other injury.
Note: If the unit is to be installed flush with the cabinets, the flush mount side trim must be installed first. If not, skip to “installation”. Step 1 Locate the necessary parts: Two (2) flush mount trim pieces and a hardware kit with twenty-two (22) screws. Step 2 Remove the side trim on the refrigerator and discard the trim and screws. Step 3 Align the top of the flush mount side trim with the top of the unit's machine compartment.
Hinge Adjustment Loosen the 4 hinge screws. Adjust door. Re tighten 4 hinge screws. Refrigerator Attach a single wall stud {refer to dimensions. If beaded, depending on cabinet and depth, page for exact location).
Plug in power cord o verify operation. Place unit within 3% of being flush with cabinets. Note: Make sure power switch and showroom switch Note: To avoid cabinet damages, place cardboard are in the “On* Position. between cabinets and unit. When moving unit, do not crimp, kink or crush water supply line. T Carefully move unit until semi flush with cabinet Pull supply tubing forward under unit. {depending on union. Note: DO NOT use plastic water lines.
L Tum on water supply and check for leaks. Lift unit off rollers to desired height and level unit using 2 5/16" head wrench. Note: DO NOT use an electric device. Over tightening can cause damage. ~ Refrigerator Attach positive secures self.tapping bolts Verify that drain pan is installed and aligned. using a 22° extension. Kick plate Installation e N Align holes on both ends of louvered panels and insert Using a Phillips screwdriver, attach the screws, kick plate to the unit and adjust to desired height.
Door Stop Ad adjustment Open refrigerator door so door stop and shoulder Remove shoulder screw and place in 90 or screw are accessible. 120" position. Note: Shoulder craw should ba in 110" door opening position. Final Installation Replace top air grille. Using an 8*magnetic nut driver, replace the two 1/4* screws. Replace the center grille louver. Open door. Display should flash.
Press "ACTIVATE CONTROLS" button pad and close door. Note: There is a 6 minute defy before the unit starts.
Q Verify cabinet size. Q Verify electrical supply and water supply (if applicable). Q Install anti-tip device(s) and verify unit is secure. Q Position unit in cutout, level at desired height, and secure unit. Q Plug-in unit and verify operation. Q Connect water supply (if applicable). * Verify ice maker fill tube is properly inserted. * Verify ice maker bail arm is down. Q Align/square door(s). Q Verify drain pan is properly installed and there are no leaks in water connection. Install kick plate.
Control Panels All Refrigerator Ac Tits CONTROLS TOP Richer Lower ‘ BEF OFF OFF All Freezer acts o wast wax arm | ms mar CONTROLS TEMP PHISHER Lower OFF OFF 1. Press "Activate Controls” pad. 2. Verify unit is not in Sabbath Mode. If in Sabbath Mode: A. The Sabbath Mode will disable the interior lights, display (except SAB indicator, temperature and compartment indicator) and alarm. To exit the Sabbath Mode: B.. Press and hold “Activate Controls” and then “Display Off” for 3 seconds.
If service is required, call your authorized service agency. Have the following information readily available. * Model number ® Serial number ® Date purchased * Name of dealer from whom purchased Clearly describe the problem that you are having.
Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 USA {662} 455-1200 For product information, call or visit our web site at vikingrange.com in the US or brigade.