Installation Instructions

ManualsBrandsViking ManualsCooking36" Wide 18" High Chimney Wall Hood - VCWH Viking 5 Series

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manufacturer.

If you have questions, contact the manufacturer or your distribu-

tor.

2. Before servicing or cleaning unit, switch power off at service

panel and lock the service disconnecting means to prevent

power from being switched on accidentally. When the service

disconnecting means cannot be locked, securely fasten a

prominent warning device, such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by a

qualified person(s) in accordance with all applicable codes

and standards, including fire-rated construction codes and

standards.

4. Sufficient air is needed for proper combustion and exhausting

of gases through the flue (chimney) of fuel burning equip-

ment to prevent backdrafting. Follow the heating equipment

manufacturer’s guidelines and safety standards such as those

published by the National Fire Protection Association (NFPA),

and the American Society for Heating, Refrigeration and Air

Conditioning Engineers (ASHRAE), and the local code authori-

ties.

5. When cutting or drilling into wall or ceiling, do not damage

electrical wiring and other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. Do not use this unit with an additional speed control device.

8. To reduce the risk of fire, use only steel ductwork.

9. This unit must be grounded.

TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

1. Never leave surface units unattended at high settings. Boilovers

cause smoking and greasy spillovers that may ignite. Heat oils

slowly on low or medium settings.

2. Always turn hood ON when cooking at high heat or when

cooking flaming foods.

3. Clean ventilating fans frequently. Grease should not be allowed

to accumulate on fan or filter.

4. Use proper pan size. Always use cookware appropriate for the

size of the surface element.

TO REDUCE THE RISK OF INJURY TO PERSONS IN THE

EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE

FOLLOWING:*

1. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or

metal tray, then turn off the burner. BE CAREFUL TO PREVENT

BURNS. If the flames do not go out immediately, EVACUATE

AND CALL THE FIRE DEPARTMENT.

2. NEVER PICK UP A FLAMING PAN - You may be burned.

3. DO NOT USE WATER, including wet dishcloths or towels -

violent steam explosion will result.

4. Use an extinguisher ONLY if:

A. You know you have a Class ABC extinguisher and you

already know how to operate it.

B. The fire is small and contained in the area where it started.

C. The fire department is being called.

D. You can fight the fire with your back to an exit.

* Based on “Kitchen Fire Safety Tips” published by NFPA.

CAUTION

1. For general ventilating use only. Do not use to exhaust haz-

ardous or explosive materials and vapors.

2. To avoid motor bearing damage and noisy and/or unbal-

anced impellers, keep drywall spray, construction dust, etc.

off power unit.

3. Your ventilator motor has a thermal overload which will au-

tomatically shut off the motor if it becomes overheated. The

motor will restart when it cools down. If the motor continues

to shut off and restart, have the hood serviced.

4. Please read specification label on product for further infor-

mation and requirements.

Model VINV300 Ventilator Kit

FOR USE ONLY WITH

VIKING HOOD MODELS *

VCWH, VWH, VBCV

* Contact your local Viking dealer for specific

compatibility information.

Blower Dimensions

9.50 x 8.50 x 8.50

MOUNTING PLATE CONFIGURATIONS:

020971-000

USE ON VCWH 30" THRU 36" HOODS

020972-000

USE ON VWH AND VBCV 30" THRU 36"

HOODS

050722-000

USE ON VBCV53638 HOODS

Summary of content (8 pages)

PAGE 1
Model VINV300 Ventilator Kit ! WARNING CAUTION TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer or your distributor. 2. Before servicing or cleaning unit, switch power off at service panel and lock the service disconnecting means to prevent power from being switched on accidentally.
PAGE 2
Model VINV300 Ventilator Kit VENTILATOR KIT INSTALLATION 1. Attach the GUARD with (3) M4 x 0.7 screws provided. 2. Choose the correct VENTILATOR MOUNTING PLATE for your hood series. (VBCV53638 will only be shipped with the 050722-000 mounting plate.) 3. Attach DAMPER to ventilator mounting plate, as shown. Use three (3) HEX SCREWS. Note: Damper FLANGE to be captured by screw heads. 4. Apply (4) NEOPRENE WASHERS (supplied) to each of the mounting plate STUDS. 5.
PAGE 3
Ensemble de ventilateur modèle VINV300 AVERTISSEMENT AVERTISSEMENT AFIN DE DIMINUER LES RISQUES D’INCENDIE, D’ÉLECTROCUTION OU DE BLESSURES, SUIVEZ CES DIRECTIVES: 1. Utilisez ce produit en suivant les recommandations du manufacturier. Pour toute question, contactez le manufacturier à l’adresse ou au numéro de téléphone indiqués dans la garantie. 2.
PAGE 4
Ensemble de ventilateur modèle VINV300 INSTALLATION DE L’ENSEMBLE DE VENTILATEUR 1. Fixez le GARDE avec (3) M4 x 0,7 vis fournies. 2. Choisissez la PLAQUE DE MONTAGE de ventilateur convenant à la série de votre hotte. (VBCV53638 seront uniquement expédiés avec les 050722-000 plaque de montage.) 3. Fixez le CLAPET à la plaque de montage, tel qu’illustré. Utilisez trois (3) VIS HEXAGONALES. Remarque : La BRIDE du clapet doit être retenue par les têtes de vis. 4.
PAGE 5
Juego de ventilador modelo VINV300 ADVERTENCIA PRECAUCIÓN PARA REDUCIR EL RIESGO DE INCENDIOS, DESCARGAS ELÉCTRICAS O LESIONES PERSONALES, OBSERVE LAS SIGUIENTES PRECAUCIONES: 1. Use la unidad sólo de la manera indicada por el fabricante. Si tiene preguntas, comuníquese con el fabricante o el distribuidor. 2.
PAGE 6
Juego de ventilador modelo VINV300 INSTALACIÓN DEL JUEGO DEL VENTILADOR 1. Coloque la GUARDIA con (3) M4 x 0,7 tornillos suministrados. 2. Elija la PLACA DE MONTAJE de ventilador correcta para la serie de su campana. (VBCV53638 sólo serán enviados con la 050722-000 placa de montaje. 3. Fije el REGULADOR a la placa de montaje del ventilador, como se muestra. Utilice tres (3) TORNILLOS HEXAGONALES. Nota: El REBORDE del regulador debe quedar atrapado por las cabezas de los tornillos. 4.
PAGE 7
Kit de ventilador modelo VINV300 AVISO apagarem imediatamente, EVACUE A ÁREA E CHAME OS BOMBEIROS. 2. NUNCA PEGUE UMA CAÇAROLA EM CHAMAS — você pode se queimar. 3. NÃO USE ÁGUA, incluindo toalhas ou panos de prato molhados, pois isso causará uma explosão violenta de vapor. 4. Use um extintor SOMENTE se: A. O extintor for da Classe ABC e você sabe como fazê-lo funcionar. B. O fogo é pequeno e está confinado na área onde começou. C. O corpo de bombeiros está sendo chamado. D.
PAGE 8
Kit de ventilador modelo VINV300 INSTALAÇÃO DO KIT DO VENTILADOR 1. Coloque a PROTEÇÃO com (3) parafusos M4 x 0,7 fornecidos. 2. Escolha a PLACA DE MONTAGEM DO VENTILADOR correta para a série da sua coifa. (VBCV53638 só serão enviados com o 050722-000 placa de montagem.) 3. Fixe o REGULADOR à placa de montagem do ventilador, conforme mostrado. Use três (3) PARAFUSOS SEXTAVADOS. Nota: O FLANGE do regulador deve ficar preso pelas cabeças dos parafusos. 4.