1500 CFM Exterior-Power Ventilator Kit - Installation Instructions

ManualsBrandsViking ManualsCooking60" Wide 18" High Chimney Wall Hood - VCWH Viking 5 Series

READ AND SAVE THESE INSTRUCTIONS

MODEL DEV1500

EXTERIOR MOUNTED VENTILATOR

WARNING

TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR

INJURY TO PERSONS, OBSERVE THE FOLLOWING:

1. Use this unit only in the manner intended by the manu-

facturer. If you have questions, contact the manufacturer

or your distributor.

2. Before servicing or cleaning unit, switch power oﬀ at

service panel and lock the service disconnecting means

to prevent power from being switched on accidentally.

When the service disconnecting means cannot be

locked, securely fasten a prominent warning device,

such as a tag, to the service panel.

3. Installation work and electrical wiring must be done by

a qualiﬁed person(s) in accordance with all applicable

codes and standards, including ﬁre-rated construction

codes and standards.

4. Suﬃcient air is needed for proper combustion and

exhausting of gases through the ﬂue (chimney) of fuel

burning equipment to prevent backdrafting. Follow the

heating equipment manufacturer's guideline and safety

standards such as those published by the National

Fire Protection Association (NFPA), and the American

Society for Heating, Refrigeration and Air Conditioning

Engineers (ASHRAE), and the local code authorities.

CAUTION

1. For general ventilating use only. Do not use to exhaust haz-

ardous or explosive material and vapors.

2. To avoid motor bearing damage and noisy and/or unbalanced

impellers, keep drywall spray, construction dust, etc. oﬀ power

unit.

3. Please read speciﬁcation label on product for further informa-

tion and requirements.

4. Electrical circuit, including speed control, (if used), must be

rated 6 AMPS minimum.

PLAN THE

INSTALLATION

1. Locate the ventilator so

the length of the duct run

and number of elbows

needed are kept to a

minimum.

2. Where possible, ventila-

tor should be centered

between wall studs or roof

rafters.

3. Avoid pipes, wires, or

other ductwork that may

be running through the

wall.

ALL INSTALLATIONS

MODEL VOLTS AMPS CFM DUCT SIZE

DEV1500 120 4.3 1500 10" DIA.

SPECIFICATIONS

INSTALLER: Leave This Manual With The Homeowner

HOMEOWNER: Use And Care Information On Page 4

TYPICAL ROOF MOUNTED INSTALLATION TYPICAL WALL MOUNTED INSTALLATION

5. When cutting or drilling into wall, or ceiling, do not dam-

age electrical wiring or other hidden utilities.

6. Ducted fans must always be vented to the outdoors.

7. To reduce risk of ﬁre, use only metal ductwork.

8. This unit must be grounded.

WARNING

MODEL DEV1500

EXTERIOR VENTILATOR

10" ROUND

DUCT

SOFFIT

WALL HOOD

CANOPY

(island canopy available)

MODEL

DEV1500

EXTERIOR

VENTILATOR

10" ROUND DUCT

SOFFIT

10" ROUND ELBOW

WALL HOOD

CANOPY

(island canopy available)

FOR USE ONLY WITH DCWH/DCWN/DCWL/DTWS/DSWB/DBCV/DCIH/DiCV/

VCWH/VCIH - 42”W - 66”W WALL AND ISLAND :-/-2+6%2+)00'HOODS.

Blower Dimensions

25 x 30.828 x 12.724

Summary of content (12 pages)

PAGE 1
MODEL DEV1500 EXTERIOR MOUNTED VENTILATOR FOR USE ONLY WITH DCWH/DCWN/DCWL/DTWS/DSWB/DBCV/DCIH/DiCV/ VCWH/VCIH - 42”W - 66”W WALL AND ISLAND :-/-2+ 6%2+) 00' HOODS. READ AND SAVE THESE INSTRUCTIONS WARNING WARNING TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING: 1. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer or your distributor. 2.
PAGE 2
PREPARE THE INSTALLATION LOCATION PREPARE THE INSTALLATION LOCATION WALL INSTALLATIONS ROOF INSTALLATIONS winds. 1. Locate the blower on the rear slope of the roof. Place it in a location to minimize duct run. The location should be free of obstacles (T.V. leads, electrical lines, etc.). If the blower top is level with the roof peak, it will not be seen from the street. Keep this approximate location in mind as you work from within the attic. 1. Choose a position on the outside wall.
PAGE 3
INstall the blower INstall the blower ROOF INSTALLATIONS WALL INSTALLATIONS 1. Remove the cover and screws. 1. Place a large bead of caulk on the back side of the housing all along the outer edges. 2. Attach an appropriate U.L. approved cable connector in the hole at the rear of the wiring box. 2. Center the blower ring in the 11" diameter hole, making sure that the 1¼" diameter electrical wiring hole aligns with the hole in the wiring box. 3.
PAGE 4
INstall the rough-in plate use and care 1. Run 10" round steel ductwork, from exterior ventilator to the installation location. For best performance, use the straightest possible duct run and the fewest number of elbows. Tape all joints. Disconnect electrical power supply and lock out service panel before cleaning or servicing this unit. CLEANING 2. Run 120 VAC electrical power cable from service panel and from remote ventilator to installation location.
PAGE 5
MODÈLE DEV1500 VENTILATEUR MONTÉ À L’EXTÉRIEUR À UTILISER UNIQUEMENT AVEC :-/-2+ 6%2+) 00' DCwh/DCwN/DCwL/DTwS/DSwB/DBCV/DCih/ DiCV/VCwh/VCih - 106,7 CM (42”) DE LARGEUR - 167,6 CM (66”) DE LARGEUR hOTTES MURALES ET ÎLOTS. VEUILLEZ LIRE CES DIRECTIVES ET LES CONSER- avertissement 6. Les ventilateurs canalisés doivent toujours être ventilés à l’air libre. 7. Pour réduire les risques d’incendie, utilisez seulement des conduits en métal.
PAGE 6
PRÉparation de l’installation PRÉparation de l’installation INSTALLATIONS SUR LE TOIT INSTALLATIONS SUR LE MUR 1. Positionez le ventilateur sur la pente arrière du toit. Placez-le de manière à minimiser la longueur des conduits. L’emplacement doit être dépourvu d’obstacles (câble de télévision, fils électriques, etc.). si le dessus du ventilateur est à égalité avec le faîte du toit, il ne sera pas visible de la rue.
PAGE 7
INSTALLATION du ventilateur INSTALLATION du ventilateur installationS sur le MUR installationS sur le toit 1. Enlevez le couvercle et les vis. 1. Appliquez une grosse bande de mastic à l’arrière du boîtier le long des arêtes extétieures. 2. Fixez un connecteur de câble adéquat portant l’homologation U.L. dans le trou arrière de las boîte de câblage. 2.
PAGE 8
uTILISATION ET ENTRETIEN POSE DE LA PLAQUE DE RACCORDEMENT Débranchez l’alimentation électrique et verrouillez le panneau d’entrée d’électricité avant de nettoyer ou de réparer l’appareil. 1. Faites cheminer les conduits ronds en acier de 25,4 cm (10 po) du ventilateur extérieur vers l’emplacement de pose. Pour un meilleur rendement, utilisez le conduit rond le plus droit possible et réduisez au maximum l’utilisation de coudes. Guipez tous les joints.
PAGE 9
VENTILADOR PARA MONTAJE EXTERIOR MODELO DEV1500 PARA USARSE ÚNICAMENTE CON LAS CAMPANAS DE PARED Y DE ISLA VIKING 6%2+) 00' DCWH/DCWN/DCWL/DTWS/DSWB/DBCV/DCIH/DICV/VCWH/VCiH DE 42 A 66 PULG. DE ANCHO (106.7 A 167.6 CM). LEA Y CONSERVE ESTAS INSTRUCCIONES ADVERTENCIA ADVERTENCIA PARA REDUCIR EL RIESGO DE INCENDIOS, DESCARGAS ELÉCTRICAS O LESIONES PERSONALES, OBSERVE LAS SIGUIENTES PRECAUCIONES: 5.
PAGE 10
PREPARE EL LUGAR DE LA INSTALACIÓN PREPARE EL LUGAR DE LA INSTALACIÓN INSTALACIONES EN LA PARED INSTALACIONES EN EL TECHO 1. Seleccione un lugar en la pared exterior. Asegúrese de que no haya montantes de la pared, tubería ni cables tendidos en el área de la abertura. 2. Desde el interior, marque y perfore un orificio guía centrado entre los montantes de la pared. Ø QUITE LAS TEJAS Viga pulg. 32.2 cm Orificio de 1 ¼ pulg. (3.2 cm) de diám.
PAGE 11
INSTALE EL VENTILADOR INSTALE EL VENTILADOR INSTALACIONES EN EL TECHO INSTALACIONES EN LA PARED 1. Quite la cubierta y los tornillos. 1. 2. Coloque un conector de cables apropiado, aprobado por U.L., en el orificio que se encuentra en la parte posterior de la caja de cableado. Coloque un reborde grande de material de calafateo en el lado posterior de la cubierta, a lo largo de todos los bordes externos. 2. Centre el anillo del ventilador en el orificio de 11 pulg. (27.
PAGE 12
INSTALE LA PLACA DE EMPALME USO Y CUIDADO 1. Tienda los conductos de acero redondos de 10 pulg. (25 cm) desde el ventilador exterior hasta el sitio de la instalación. Para un mejor rendimiento, use el tendido de tubería más recto posible y el menor número de codos. Ponga cinta en todas las uniones. Desconecte el suministro eléctrico y bloquee el panel de servicio antes de limpiar o dar servicio a esta unidad. LIMPIEZA 2.