Installation GUIDE 7 SERIES Multi-Unit Refrigeration Connector Kit CKVBI
Table of Contents NOTE: These instructions include information on how to install multiple 7 Series refrigeration units. For information on dimensions, specifications, and installation of single units, please refer to the installation guide included with the appliances.
Cutout Dimensions 25” ) cm (63.5 Can be lo cated on Electric Outlet Location either sid e 1 5-1/ (39.4 2” cm) 4-1/4 (10.8 ” cm) + leveli dimenng sion * (213 84” .4 ope cm) m ning in heig . ht 85 (216 -3/16” .3 ope cm) ma ning x. heig ht Water Line Entry Area *Cut o Wid ut th *Re 5/8 (1.6 ” cm) fer to S spe chart pecific cific fo atio n Mod r els 1/2 (1.3 ” cm) 3” (7.6 6 (15.
Specifications Refer to Installation Guides included with unit for individual dimensions. Below is a common install chart for reference. Cabinet Cutout Height (same for all) Cabinet Cutout Depth (same for all) Optional Kickplate Size Combination Cabinet Cutout Width 18” W / 24”W Models 42” (106.7 cm) TKK742SS 18” W / 30”W Models 48” (121.9 cm) TKK748SS 18” W / 36”W Models 54” (137.2 cm) TKK754SS 24” W / 24”W Models 48” (121.9 cm) TKK748SS 24” W / 30”W Models 54” (137.
Anti-tip Location C Anti-tip Bracket The anti-tip bracket has several holes set up on a grid in order to better locate a wall stud. At least 4 places must be used. Anti-tip Bracket must be centered in cutout - side to side. Cabinet Opening NOTE: Number and type of fasteners must be suitable in order to prevent tipping. For example: use wood screws into wall studs or masonry anchors if attaching to stone, brick or concrete.
Preparing Units for Installation Before removing units from pallet, remove the side trim from each unit, install center trim brackets and connection heater (steps 1 thru 4). Make sure units are unplugged and powered off. A Look closely at the trim already installed on the unit. If the trim resembles that in Trim A, it will need to be removed and replaced with Trim B. If the trim already resembles Trim B, leave as is.
Preparing Units for Installation 3. Fasten heater (Item #1) to the three mounting holes on top of the right hand unit using the #8-18 x 1/2” fasteners (Item #7) provided. 4. Plug heater terminal into right hand unit using the plug located next to the unit on/off switch.
Installation WARNING TIP OVER HAZARD Appliance is top heavy and tips easily when not completely installed. Keep doors closed until appliance is completely installed and secured per installation instructions. Use two or more people to move and install appliance. Failure to do so can result in death or serious injury. 5. Remove units from pallets and position together outside of the cabinet so that top connecting plate (Item #4) can be installed.
Installation 8. If unit leveling feet were used, lower units back onto rollers. Plug in electrical supply and roll connected units into cabinet cutout. Units must be plugged into separate electric outlets. Connect water supply to each unit. 9. Lift units to desired height using 5/16” socket and hand ratchet. DO NOT USE A DRILL-(refer to lift pattern diagram below to ensure that units are gradually lifted together.) **IMPORTANT** - Only make 4 turns at a time with the hand ratchet**.
Installation 10. Remove plastic film from center trim before installing. Install center connecting trim (Item #3) in between the two units by pressing it in. Trim should be even with the top of the units. If needed, tap connecting trim gently into place with rubber mallet. NOTE: Open both doors to install the trim. When installed, the face of the trim should be flush with the breaker frame. 11.
Optional Custom Kickplate Installation Remove screws fastening individual kickplates on units. Save screws to be used when installing custom kickplate. Place custom kickplate across bottom of both units and fasten using the mounting holes for the individual kickplates.
Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 (662) 455-1200 For product information, call 1-888-845-4641 or visit our web site at vikingrange.
Guide d’installation SÉRIE 7 Kit d'assemblage de plusieurs appareils de réfrigération CKVBI
Table des matières REMARQUE : ces instructions contiennent des renseignements sur l'assemblage de plusieurs appareils de réfrigération série 7. Pour plus de renseignements sur les dimensions, les spécificités et l'installation individuelles des appareils, veuillez vous référer aux guides d'installation fournis avec ces derniers.
Dimensions de découpe 25 po m) (63,5 c Peut être Emplacement de la prise électrique situé de l' autre côté 15-1/ (39,4 2 po cm) 4-1/4 (10,8 po cm) + dimen s mise ion de à nive au 84 p * (21 o haut 3,4 cm) eur d m e l'o in. uver ture 85-3 / 16 (2 haut 16,3cm po ) eur de l' max.
Spécificités Pour obtenir les dimensions individuelles des appareils, veuillez vous référer aux guides d'installation fournis avec ceux-ci. Le tableau ci-dessous répertorie les combinaisons les plus fréquentes.
Système anti-basculement C Support anti-basculement Le support anti-basculement dispose de 12 trous. Au moins 4 de ces 12 trous doivent être utilisés. Ouverture de l'encadrement REMARQUE : le nombre d'attaches doit être adapté à la charge afin d'écarter tout risque de basculement. Par exemple : utilisez des vis à bois pour les murs et des clous ou des ancrages de maçonnerie si l'installation se fait sur de la pierre, de la brique ou du béton.
Préparation des unités pour l'installation Avant de retirez les appareils de leur socle, retirez les tiges latérales de chaque appareil et installez les supports de tige centrale ainsi que le chauffage de liaison (étapes 1 à 4). Assurez-vous que les appareils sont bien éteints et débranchés. A 1. Retirez les tiges du montant des appareils sur les côtés où ils seront en contact (TIGE A). Laissez la tige sur les côtés qui seront en contact avec l'encadrement.
Préparation des unités pour l'installation 3. Fixez le chauffage (élément nº 1) aux trois trous en haut de l'appareil de droite à l'aide des attaches 8-18 x 1/2 po (élément nº 7) fournies. 4. Branchez le chauffage à l'appareil de droite en utilisant la prise située à côté de l'interrupteur marche/arrêt.
Installation AVERTISSEMENT RISQUE DE BASCULEMENT Le haut de l’appareil est lourd et l'appareil peut donc facilement basculer tant que son installation n’est pas terminée. Maintenez les portes fermées jusqu’à l'installation et la sécurisation complète de l’appareil conformément aux instructions d’installation. Il faut deux personnes ou plus pour installer et déplacer l’appareil. Le non-respect de cette consigne peut entraîner la mort ou de graves blessures. 5.
Installation 8. Dans le cas où les pieds de nivellement seraient détériorés, réduisez la hauteur des appareils de façon à ce qu'ils reposent sur leurs roulettes. Branchez l’alimentation électrique et enroulez les unités connectées dans la découpe du meuble. Les appareils doivent être branchés dans des prises électriques séparées. Raccorder l’alimentation d’eau à chaque unité. 9. Surélevez les appareils à la hauteur désirée à l'aide des pieds de nivellement et enclenchez le support anti-basculement.
Installation 10.. Insérez la tige de liaison centrale (élément nº 3) entre les deux appareils en faisant pression. La tige doit être alignée avec le haut des appareils. En cas de besoin, enfoncez délicatement la tige à l'aide d'un maillet en caoutchouc. REMARQUE : ouvrez les deux portes pour installer la tige. Une fois l'installation terminée, la face de la tige doit être au même niveau que le cadre du disjoncteur 11.
Installation facultative de la plaque de protection sur mesure Retirez les vis fixant les plaques de protection individuelles des appareils. Conservez les vis pour fixer la plaque de protection sur mesure. Placez la plaque de protection en bas à l'arrière des appareils et fixez-la aux trous libérés par les plaques individuelles.
Viking Range, LLC 111 Front Street Greenwood, Mississippi 38930 É.-U. (662) 455-1200 Pour obtenir des renseignements sur le produit, appelez au 1-888-845-4641 ou visitez notre site Web au vikingrange.