Installation Guide

ManualsBrandsVILLA BATH by RSI ManualsLinen CabinetsLVM18LD-CMB

APPLY FLUSH-FIT END PANEL TO CABINET SIDE PANEL

a) Remove the backer from each tape strip.

b) Holding the ﬂush-ﬁt end panel at an angle from the cabinet side panel, align

the front edge of the ﬂush-ﬁt end panel to the face frame. Make sure the entire

edge of the ﬂush-ﬁt end panel is seated inside the face frame groove.

c) Align the top of the ﬂush-ﬁt end panel with the top of the cabinet side panel

and press the ﬂush-ﬁt end panel against the side panel.

d) Working from front to back, apply pressure along the entire surface of the

ﬂush-ﬁt end panel to make sure each tape/adhesive strip makes complete

contact with the cabinet side panel.

e) Allow the tape/adhesive to cure for at least 1 hour before proceeding with the

cabinet installation. Clamps or weights can be added to secure panel until

adhesive dries. Check adhesive manufacturer’s instructions for cure time.

INSTALL LINEN CROWN MOULDING

Crown moulding, sold separately, can be installed on the

linen cabinet. The length of crown moulding pieces will

need to be cut from the full-length piece. You will need to

miter the pieces to ﬁt the linen. Please see Figures 2 and

3 on how to install the crown moulding to the cabinet. If

your linen will be installed with a side against a wall it is

not necessary to attach moulding to the side against the

wall. Cut to ﬁt your wall (Figure 4).

Options for attachment: #6 x 3/4 in. wood screws or

brad nails (neither are provided). Pre-drilling pilot holes

ﬁrst will help prevent splitting.

Figure 3

Side moulding

Left side

moulding

Use #8 x 7/8 in.

screw

(not provided)

Use either white

glue or carpenter’s

glue (not provided)

Front moulding

ATTACH RIGHT AND LEFT

SIDE MOULDINGS

Note: Make sure to align

side mouldings with front

moulding.

TOP VIEW

Figure 4

Wall

Front moulding straight cut to fit to wall

Cabinet

Wall

FRONT VIEW

Figure 2

Front moulding

ATTACH FRONT MOULDING

UPPER FLUSH-FIT END PANEL

Before beginning the cabinet installation, you will need to apply the ﬁnished ﬂush-ﬁt

end panels to the side(s) of the cabinet that will be exposed to the room.

Refer to Instructions provided with ﬂush-ﬁt end panels for the base.

MATERIALS

Finished ﬂush-ﬁt end panel and a roll of double-sided tape (suggested 1 roll per

ﬂush-ﬁt end panel) or construction adhesive or white glue (neither are provided).

Figure 1

NOTE: Tape/adhesive should be applied ¼ in.

from edges of flush-fit end panel.

Tape/

adhesive

Tape/

adhesive

U180175A

Rev. 09-14

LINEN INSTALLATION

Hardware for installation not included.

Summary of content (6 pages)

PAGE 1
LINEN INSTALLATION U180175A Hardware for installation not included. UPPER FLUSH-FIT END PANEL Before beginning the cabinet installation, you will need to apply the finished flush-fit end panels to the side(s) of the cabinet that will be exposed to the room. Rev. 09-14 NOTE: Tape/adhesive should be applied ¼ in. from edges of flush-fit end panel. Refer to Instructions provided with flush-fit end panels for the base.
PAGE 2
-PIECE LINEN ASSEMBLY The linen with drawers and linen with doors are 2-piece units that require assembly prior to installation. The upper unit has four attachment brackets (provided in parts bag) that need to be installed at the bottom interior of the unit. Install the brackets on the upper unit before placing on top of the base. Pre-drilling pilot holes will ease the seating of the screws Bottom Panel of Upper Unit (Figure 5).
PAGE 3
Care and Cleaning EXTERIOR CARE AND CLEANING INTERIOR CARE AND CLEANING For normal spills, a damp cloth is sufficient. Remember to dry the surface immediately. Lemon oil is recommended for cleaning wood doors. Most furniture care products, not containing wax, petroleum solvents or silicone can be used for polishing. Do not use caustic agents and/or abrasive scrubbers. Nicks and dings can be repaired using the color sticks. Fill in the scratch or nick using the color stick.
PAGE 4
INSTALACIÓN DE GABINETE DE LENCERÍA Aditamentos para la instalación no incluidos. PANEL DE EXTREMO DE INSTALACIÓNAL RAS SUPERIOR Antes de comenzar la instalación del gabinete, deberá aplicar los paneles de extremo de instalación al ras con acabado a los laterales del gabinete que estarán expuestos en la habitación. Remítase a las instrucciones proporcionadas con los paneles de extremo de instalación al ras para la base.
PAGE 5
ENSAMBLAJE DE 2 PIEZAS PARA GABINETE DE LENCERÍA El gabinete de lencería con gavetas y puertas es una unidad de 2 piezas que requiere de un ensamble previo a la instalación. La unidad superior tiene cuatro abrazaderas de fijación (provistas en la bolsa de Panel inferior de la unidad superior las piezas) que deben instalarse en la parte interna inferior de la unidad. Instale las abrazaderas en la unidad superior antes de colocarla sobre la base.
PAGE 6
Cuidado y limpieza CUIDADO Y LIMPIEZA DEL EXTERIOR CUIDADO Y LIMPIEZA DEL INTERIOR En caso de derrames habituales, es suficiente con un paño húmedo. Recuerde secar la superficie de inmediato. Se recomienda usar aceite de limón para la limpieza de puertas de madera. La mayoría de los productos para el cuidado de muebles, que no contengan vera, solventes de petróleo ni silicona, pueden usarse para pulir. No use productos cáusticos ni limpiadores abrasivos.