Vincent Bedienungsanleitung deutsch Instructions for use english Manuel d‘utilisation français SP-T800 Hybrid-Mono-Endverstärker mit Class-A-Schaltung Monaural Class A Hybrid Power Amplifier Amplificateur mono hybride Classe A
Sehr geehrter Kunde, wir danken Ihnen für das Vertrauen, welches Sie uns durch die Entscheidung für dieses hochwertige AudioProdukt, das Ihrem hohen Anspruch an Klang- und Verarbeitungsqualität gerecht wird, entgegenbringen. Auch wenn Sie verständlicherweise sofort beginnen wollen, das Gerät zu verwenden, lesen Sie bitte vor dem Aufstellen und Anschließen dieses Handbuch sorgfältig durch.
INHALTSVERZEICHNIS/CONTENTS/SOMMAIRE Sicherheitshinweise Weitere Hinweise Lieferumfang Beschreibung des Gerätes Installation Bedienung des Gerätes Weitere Tipps Fehlertabelle Technische Daten Lexikon/Wissenswertes 4 5 6 6 9 14 15 15 17 17 deutsch Safety guidelines Other instructions Included in delivery Description of the appliance Installation Operating the appliance Tips Search for errors Technical Specifications Glossary 18 19 20 20 23 28 29 29 31 31 english Consignes de sécurité Autres consignes Con
SICHERHEITSHINWEISE Dieses Gerät wurde unter strengen Qualitätskontrollen gefertigt. Es entspricht allen festgelegten internationalen Sicherheitsstandards. Trotzdem sollten folgende Hinweise vollständig gelesen und beachtet werden, um eine Gefährdung zu vermeiden: Das Gerät nicht öffnen! Gefahr des elektrischen Schocks! Es befinden sich keine vom Benutzer zu wartenden Teile im Gerät.
WEITERE HINWEISE Aufstellen des Gerätes Die Art der Aufstellung der Anlage hat klangliche Auswirkungen. Stellen Sie diese deshalb nur auf eine dafür geeignete, stabile Unterlage. Um das Klangpotential Ihres Systems optimal auszunutzen, empfehlen wir, die Geräte auf Vincent Racks zu platzieren und nicht aufeinander zu stellen.
LIEFERUMFANG Bitte prüfen Sie den Inhalt der Verpackung, diese sollte zusätzlich zum Gerät folgendes Zubehör enthalten: • 1 Netzkabel • 1 Kabel für die Einschaltsteuerung (POWER CONTROL) • dieses Handbuch BESCHREIBUNG DES GERÄTES Obwohl Vincent auch für Mehrkanaltonanlagen und Heimkinos langlebige und überlegene Komponenten herstellt, fühlen sich die Vincent-Entwickler besonders der Stereo-Tradition verpflichtet.
VORDERANSICHT 2 1. POWER: Netzschalter Schaltet das Gerät ein und aus. Im ausgeschalteten Zustand ist das Gerät nicht vom Netz getrennt und reagiert auf die Einschaltsteuerung. 1 2 2. SPEAKER A/B: Tasten zum Aktivieren und Abschalten der beiden Lautsprecher Wenn geeignete Lautsprecher verwendet werden, kann auch ein zweiter Lautsprecher gleichzeitig betrieben werden. Mit diesen Tasten lässt sich jeder der beiden Lautsprecher (A und B genannt) einzeln ein- und ausschalten.
RÜCKANSICHT 3 4 5 3. LINE IN: Eingang für vorverstärktes Mono-Audiosignal Ein Anschluss dieses Eingangs wird mit dem Ausgangsanschluss des Vorverstärkers für den gewünschten Kanal verbunden. Zum Beispiel mit „PRE OUT R“, wenn der SP-T800 für den Lautsprecher des rechten Stereo-Kanals verwendet werden soll. Es kann immer nur einer der beiden Anschlüsse des Eingangs verwendet werden, der Umschalter „XLR/RCA“ muss sich in der richtigen Position befinden. Keine Hochpegelquelle anschließen! 4.
INSTALLATION Stellen Sie die Kabelverbindung in der nachfolgend genannten Reihenfolge her. Bringen Sie erst zuletzt das Netzkabel an und verbinden es mit der Steckdose. ZUR BESONDEREN BEACHTUNG Entfernen der Schutzkappen Vor der ersten Installation müssen von allen verwendeten Anschlüssen an der Geräterückseite die Kunststoff-Schutzkappen entfernt werden.
ANSCHLUSS DES VORVERSTÄRKERS Dieser Endverstärker ist mit einem Mono-Audioeingang („LINE IN“) versehen, an welchem das Gerät das vorverstärkte Signal eines Audio-Kanals (zum Beispiel „PRE OUT R“ oder „FRONT R“) erwartet. Dies ist die Audio-Information, welche der SP-T800 für einen oder zwei Lautsprecher aufbereitet. Hinweis: An diesen Eingang darf keine Quelle mit Standard-Hochpegelsignal („LINE OUT“) angeschlossen werden. Er ist nur für vorverstärkte Signale (z.B. „PRE OUT“) vorgesehen.
KABELVERBINDUNGEN FÜR DIE EINSCHALTSTEUERUNG (POWER CONTROL) Viele AV-Systeme bestehen aus einer Vielzahl von Einzelkomponenten. Um diese nicht vor und nach jedem Gebrauch alle einzeln aus- und einzuschalten, haben manche Hersteller die Geräte mit einer so genannten „Power Control“-Schaltung, auch „Trigger“ oder „Einschaltsteuerung“ genannt, ausgestattet. Vor allem für Vor- und Endstufen wird diese Art der ferngesteuerten Standby-Schaltung verwendet.
ANSCHLUSS DES NETZKABELS Prüfen Sie, ob die Stromversorgung Ihres Haushalts für das Gerät geeignet ist. Benötigte Spannung und Frequenz sind auf der Geräterückseite neben der Netzbuchse abzulesen. Wenn die Stromversorgung geeignet ist, drücken Sie den Kaltgerätestecker des mitgelieferten Netzkabels fest in die Netzbuchse an der Geräterückwand. Verbinden Sie das andere Ende des Netzkabels mit einer Netzsteckdose.
ANSCHLUSS DER LAUTSPRECHER Wenn ein Lautsprecher im „Bi-Wiring“ angeschlossen werden soll, können beide LautsprecherKlemmenpaare verwendet werden. Anders als beim Anschluss der Lautsprecher mit je einem Lautsprecherkabel wird bei Bi-Wiring der dafür geeignete Lautsprecher über zwei getrennte zweiadrige Lautsprecherkabel oder ein vieradriges Lautsprecherkabel an das Ausgangsklemmenpaar des Endverstärkers angeschlossen.
ANSCHLUSS DER LAUTSPRECHER Wenn an das Lautsprecherkabel keine Steckverbinder angebracht werden sollen, entfernen Sie ein ca. 1 cm langes Stück der Isolierung von jedem Endstück des Lautsprecherdrahtes. Verdrillen Sie die blanke Litze, um Kurzschlüsse zu vermeiden. Drehen Sie den Knopf der Lautsprecherklemme im Gegenuhrzeigersinn, um ihn zu lösen und führen Sie das blanke Drahtende in das nun freiliegende Klemmenloch ein.
WEITERE TIPPS Einspielzeit / Aufwärmen Ihre Audio-Geräte benötigen eine gewisse Zeit bis sie ihre klangliche Höchstleistung erreichen. Dieser Zeitraum ist für die verschiedenen Komponenten Ihres Systems sehr unterschiedlich. Bessere und gleichförmigere Leistung erhalten Sie während der Zeit, die das Gerät eingeschaltet bleibt.
FEHLERSUCHE Symptom Mögliche Fehlerursache Abhilfe Kein Ton, obwohl Gerät eingeschaltet und aktiv Das momentan am Vorverstärker eingestellte Quellgerät gibt kein Signal aus. Starten Sie die Wiedergabe der angeschlossenen Signalquelle. Ausgang des Quellgerätes nicht oder falsch bzw. nicht mit dem gewünschten Eingangsanschluss des Vorverstärkers verbunden. Korrigieren Sie den Anschluss der Signalquelle. Falscher Eingangskanal am Vorverstärker gewählt. Korrigieren Sie die Eingangswahl.
TECHNISCHE DATEN Frequenzgang: Nennausgangsleistung in Class A an 8Ω: Nennausgangsleistung RMS an 8Ω: Nennausgangsleistung RMS an 4Ω: Eingangsempfindlichkeit: Klirrfaktor: Signal-Rausch-Abstand: Eingangsimpedanz: Netzanschluss: Eingänge: Ausgänge: Maße (BxHxT): Gewicht: Farbe: Röhren: 20 Hz - 20 kHz ±0,5 dB 20 Watt 200 W 320 W 1,1 V < 0,1% (1 kHz, 1 W) > 90 dB 47 kΩ 230 V/50 Hz 1x Cinch Main Input mono, 1x XLR Main Input mono, 1x Power Control (3,5mm Klinke) 2x 2 Lautsprecherklemmen, 1x Power Control (3,5m
SAFETY GUIDELINES This appliance was produced under strict quality controls. It complies with all established international safety standards. Nonetheless, the following instructions should be fully read and observed in order to prevent any hazard: Do not open the appliance! Risk of electric shock! There are no parts in the appliance that require maintenance by the user.
OTHER INSTRUCTIONS Setting up the appliance How the system is set up has an effect on the sound quality. Therefore only place it on a suitable, stable surface. To make the most of your system’s sound quality, we recommend placing the equipment on Vincent racks and not putting them on top of each other. Old electronic equipment This appliance is subject to the conditions set out in the European Directive 2002/96/EC. This is identified by the symbol of a crossed out waste bin on the appliance.
INCLUDED IN DELIVERY Please check the contents of the packaging, which in addition to the appliance should contain the following accessories: • 1 power cable • 1 cable for the POWER CONTROL • this manual DESCRIPTION OF THE APPLIANCE Although Vincent also manufactures long-lasting and high-class components for multi-channel audio units and home cinemas, Vincent’s developers feel especially dedicated to the stereo tradition.
FRONT VIEW 2 1. POWER: Mains switch This is the main power switch for turning on and off the device. When switched off, the device is not disconnected from the mains and reacts to the “Power Control” signal. 1 2 2. SPEAKER A/B If suitable speakers are used, a second loudspeaker can be operated at the same time. This button allows each of the speakers (designated A and B) to be individually switched on and off. The LED located above each of the buttons shows which of the speakers is activated.
REAR VIEW 3 4 5 3. LINE IN: Input for preamplified mono audio signal One connector of this input must be connected with the output connector of the preamplifier for the desired channel. For example, with “PRE OUT R”, if the SP-T800 is to be used for the loudspeaker of the right-hand stereo channel. Only one of the two input connectors can be used at any time. The switch “XLR/RCA” must be in the correct position. Do not connect any line level sources! 4.
INSTALLATION Set up the cable links in a sequence as follows. Connect the power cable between device and power supply only after all other connections have been made. DURING INSTALLATION PLEASE OBSERVE THE FOLLOWING ADVICE: Protective caps Prior to the first installation the protective plastic caps must be removed from all the connections used at the rear of the unit.
CONNECTING THE PREAMPLIFIER This main amplifier is equipped with a mono audio input (“LINE IN”) on which the unit awaits the preamplified signal of an audio channel (for example “PRE OUT R” or “Front R”). This is the audio information that the SP-T800 provides for one or two loudspeakers. Please note: No source with a standard line level signal (“LINE OUT”) must be connected to this input. It is only intended for preamplified signals (e.g. “PRE OUT”).
CONNECTIONS FOR THE STANDBY CONTROL (POWER CONTROL) Many AV-Systems consist of a multitude of individual components. To avoid the necessity of switching them on and off before and after every use, many manufacturers have equipped their devices with what is known as “POWER CONTROL” circuit or “TRIGGER”. This kind of remote-controlled standby circuit is used primarily for preamplifier and power amplifiers.
CONNECTION OF THE POWER CABLE Check that the electricity supply to your home is appropriate to the device. The required voltage and frequency can be read on the back of the device beside the socket for the mains. If the electricity supply is appropriate, push the inlet connector of the supplied mains cable firmly into socket for the mains on the back of the device (6). Connect the other end of the mains cable to a mains socket.
CONNECTION OF THE LOUDSPEAKERS If a loudspeaker is to be connected with “bi-wiring”, both pairs of loudspeaker clamps may be used at the same time. In contrast to connection of the loudspeakers with one loudspeaker cable each, with bi-wiring a suitable loudspeaker is connected via two separate two-wire loudspeaker cables or one four-wire loudspeaker cable to the pair of output clamps on the main amplifier.
CONNECTION OF THE LOUDSPEAKERS If no connector is to be used, remove approximately 1 cm length of insulation from each end of the speaker wire. Twist the braid in order to avoid short circuits. Turn the fastener on the loudspeaker terminal counterclockwise to loosen it and introduce the bare wire end into the exposed connector hole. Then turn the fastener clockwise so that the wire is firmly clamped. Make sure the connection is pretty tight.
TIPS Burn in/ Warm up Your audio components need a certain time period until they reach maximum performance. The duration of this “warm up” time is very different for the various elements of your audio system. Higher and homogeneous sound quality is achieved while keeping the device switched on. Your audio specialist dealer has enough experience to give you more information.
SEARCH FOR ERRORS Symptom Possible Cause Countermeasure No sound although the unit is ready for use The audio source currently selected at the preamplifer is giving no signal. Switch on the source unit and begin playback. The output of the source device is not connected or is wrongly connected e.g. not connected to the selected input channel terminal of the preamplifier. Correct the connection of the signal source. Wrong input channel has been selected at the preamplifier.
TECHNICAL SPECIFICATIONS Frequency response: Nominal Output Power in Class A at 8ø: Nominal Output Power (RMS) at 8ø: Nominal Output Power (RMS) at 4ø: Input sensitivity: Total Harmonic Distortion: Signal to Noise Ratio: Input Impedance: AC power connection type: Inputs: Outputs: Dimensions (W x H x D): Weight: Colour: Tubes: 20 Hz - 20 kHz ±0.5 dB 20 W 200 W 320 W 1.1 V < 0.1% (1 kHz, 1 W) > 90 dB 47 kΩ 230 V/50 Hz 1x RCA Main Input mono, 1x XLR Main Input mono, 1x Power Control (3.
CONSIGNES DE SECURITE La construction de cet appareil a été soumise à des contrôles de qualité très stricts. Il répond à toutes les normes internationales de sécurité. Il est cependant nécessaire de lire entièrement les consignes suivantes et de les appliquer pour éviter tout danger : Ne pas ouvrir l'appareil! Danger de décharge électrique! Aucune pièce à entretenir par l'utilisateur ne se trouve dans l'appareil.
AUTRES CONSIGNES Montage de l'appareil Le site de montage de l'appareil a une incidence sur le son. Posez l'appareil uniquement sur une surface appropriée et stable. Pour profiter pleinement du potentiel sonore de votre système, nous vous recommandons de placer les appareils sur des racks Vincent et de ne pas les poser l'un sur l'autre. Appareils électroniques usagés Cet appareil est soumis aux dispositions fixées dans la directive européenne 2002/96/ CE.
CONTENU DE LA LIVRAISON Veuillez contrôler le contenu de l'emballage. Les accessoires suivants doivent être joints à l'appareil : • 1 câble de distribution • 1 câble avec fiches Jack 3,5 mm • le présent manuel DESCRIPTION DE L'APPAREIL Bien que Vincent fabrique aussi pour des installations audio multicanal et de home cinéma des composants de qualité supérieure et à longue durée de vie, les développeurs de Vincent se sentent plus particulièrement engagés dans la stéréo traditionnelle.
FACADE AVANT 2 1. POWER : Interrupteur secteur Met l’appareil en MARCHE ou à l’ARRET, à l’ARRET. En position ARRET, l’appareil n’est pas coupé du secteur et réagit à la commande de commutation. 1 2 2. SPEAKER A/B : touches de commutation ou de coupure des deux haut-parleurs Avec des haut-parleurs appropriés, on peut aussi utiliser simultanément un deuxième haut-parleur. Avec ces touches, on peut commuter ou couper séparément chacune des deux haut-parleurs (désignées par A et B).
FACADE ARRIERE 3 4 5 3. LINE IN: Entrée du signal audio mono préamplifié Une prise de cette entrée doit être reliée à la prise de sortie du préamplificateur du canal souhaité. Par exemple avec « PRE OUT R », si le SP-T800 doit être utilisé pour le haut-parleur du canal stéréo droit. A tout moment, on ne peut utiliser qu’une seule des deux prises de l’entrée, l’inverseur « XLR/RCA » doit se trouver dans la bonne position. Ne pas raccorder de source de haut niveau ! 4.
INSTALLATION Réalisez les raccordements des câbles dans l’ordre suivant. Raccordez le cordon secteur en dernier, et reliez-le à une prise secteur. VEUILLEZ TENIR COMPTE DES INSTRUCTIONS SUIVANTES LORS DE L’INSTALLATION : Dépose du capot de protection Avant la première installation, retirez les capuchons de protection des connecteurs à utiliser, situés sur la façade arrière de l’appareil. 1 2 BALANCE les deux appareils sont de fabrication Vincent.
RACCORDEMENT DU PREAMPLIFICATEUR Cet amplificateur de puissance est équipé d’une entrée audio mono (« LINE IN »), par laquelle l’appareil reçoit le signal préamplifié d’un canal audio (par exemple « PRE OUT R » ou « FRONT R »). Ceci est l’information audio, que le SP-T800 traite pour un ou deux haut-parleurs. Consigne : Ne pas raccorder à cette entrée, une source de signal standard de haut niveau (« LINE OUT ») car elle n’est prévue que pour des signaux préamplifiés (par exemple « PRE OUT »).
LIAISONS CÂBLÉES POUR LA COMMANDE DE MISE SOUS TENSION (POWER CONTROL) De nombreux systèmes AV se composent de nombreux composants individuels. Pour éviter de les mettre en marche et de les arrêter l’un après l’autre à chaque utilisation, certains fabricants ont équipé les appareils avec un circuit appelé « Power Control », ou aussi « Trigger » ou encore « Commande de mise sous tension ». Ce type de télécommande Standby est avant tout utilisé pour les préamplificateurs et les amplificateurs.
RACCORDEMENT DU CORDON D’ALIMENTATION SECTEUR Assurez-vous que la tension d’alimentation électrique de votre habitation est conforme à celle exigée par l’appareil. La tension et la fréquence demandée sont à relever à l’arrière de l’appareil à côté de la prise secteur. Si l’alimentation secteur est conforme, enfoncez entièrement la fiche protégée du cordon d’alimentation fourni, dans la prise secteur à l’arrière de l’appareil. Reliez l’autre extrémité du cordon secteur à une prise secteur.
BRANCHEMENT DES HAUT-PARLEURS Si un haut-parleur doit être raccordé en « Bi-Wiring », on peut utiliser les deux paires de bornes de serrage du haut-parleur. A la différence d’un raccordement de haut-parleur à l’aide d’un câble de hautparleur, en Bi-Wiring le haut-parleur en question est raccordé par deux câbles deux-conducteurs séparés ou un câble de haut-parleur quatre-conducteurs, à la paire de bornes de serrage de l’amplificateur de puissance.
BRANCHEMENT DES HAUT-PARLEURS En l’absence de cosse, retirez l’isolant de chaque extrémité du câble sur une longueur d’un cm environ. Torsadez le câble dénudé, pour éviter les court-circuits, desserrez la molette de fixation en la tournant dans le sens antihoraire et insérez l’extrémité du câble dans le perçage dégagé du bornier. Serrez maintenant le câble en faisant tourner la molette de serrage dans le sens horaire. Contrôlez le serrage correct du câble.
CONSEILS Temps de rodage / échauffement Vos appareils audio demandent un certain temps pour atteindre leurs performances maximales. Ce laps de temps est très différent pour les différents composants de votre système. Vous obtiendrez un son de meilleure qualité et plus homogène en laissant l’appareil sous tension. Profitez de l’expérience de votre revendeur! Ronflement du secteur Certaines sources audio peuvent provoquer, en liaison avec l’amplificateur, un ronflement perceptible dans les haut-parleurs.
RESOLUTION DE PROBLEMES Symptom Cause possible du défaut Remède Pas de son, bien que l’appareil soit sous tension et activé L’appareil source sélectionné actuellement au préamplificateur n’émet pas de signal. Lancez la lecture de la source de signal raccordée. La sortie de l’appareil source n’est pas ou est mal raccordée ou pas raccordée à la bonne borne d’entrée du préamplificateur. Corrigez la liaison de la source de signal. Le mauvais canal d’entrée a été sélectionné au préamplificateur.
CARACTERISTIQUES TECHNIQUES Plage de transmission : Puissance de sortie nominale à 8Ω Classe A : Puissance de sortie nominale à 8Ω : Puissance de sortie nominale à 4Ω : Sensibilité d’entrée : Facteur de distorsion : Rapport signal/bruit : Impédance d’entrée : Alimentation : Entrées : Sorties : Dimensions (L x H x P) : Poids : Variante de couleur : Tubes : 20 Hz - 20 kHz ±0,5 dB 20 W 200 W 320 W 1,1 V < 0,1% (1 kHz, 1 W) > 90 dB 47 kΩ 230 V/50 Hz 1x RCA Main Input mono, 1x XLR Main Input mono, 1x Power Cont
NOTIZEN / NOTES 46 Vincent
NOTIZEN / NOTES Vincent 47
Vincent Bewahren Sie die Kaufquittung zusammen mit der Bedienungsanleitung auf. Die Kaufquittung dient Ihnen als Nachweis für den Beginn der Garantiezeit. Die Seriennummer befindet sich an der Rückseite des Gerätes. Please keep the receipt, store it together with this manual. The receipt is your proof for the beginning of the warranty period. Note the serial number in the following box, you can read it from the rear side of the device. Gardez soigneusement la facture d'achat et le mode d'emploi.