By Owner’s Manual 6-Bottle Dual-Zone Wine Cooler IL-OW006 -2Z (6 bottle)
TABLE OF CONTENTS IMPORTANT SAFETY INSTRUCTIONS ...................................................... 3 ELECTRICAL CONNECTION ..................................................................... 4 INSTALLATION INSTRUCTIONS ............................................................... 4 OPERATING YOUR WINE COOLER .......................................................... 5 WALL INSTALLATION GUIDELINES .......................................................... 7 CARE AND MAINTENANCE ......................
Please read and follow all safety rules and operating instructions before using. IMPORTANT SAFETY INSTRUCTIONS To reduce the risk of fire, electrical shock or injury when using your appliance, follow these basic precautions: • Ensure that the wine cooler stays in the upright position during transportation. • Place the wine cooler on a strong, level surface. • This wine cooler is designed for indoor, household use only. Any other use will void the warranty.
ELECTRICAL CONNECTION Improper use of the grounded plug can result in the risk of electrical shock. If the power cord is damaged, frayed or shows cracks or abrasions across its length, have it replaced at an authorized service center. For your protection, this unit is equipped with a 3-conductor cord set that has a molded 3-prong grounding-type plug, and should be used in combination with a properly connected grounding-type outlet.
Defrosting: 1. Your wine cooler will defrost every 8 hours for a period of approximately 30 minutes. Condensation will accumulate in the evaporator drip tray and will eventually evaporate. While your cooler is defrosting, the temperature displayed may be higher than the temperature set. 2. You may notice condensation on the glass exterior of your unit. If you notice an excessive amount of condensation on or around your unit, please relocate it to a less humid location. Drain: 1.
2. Set the desired cooling temperature by pressing the corresponding buttons for “set lower” program. Pressing the button once will decrease the temperature by 1 degree. The temperature selected will flash in the LED display for approximately 5 seconds and then revert back to display the temperature of the internal cooler. The left zone can be adjusted from 5℃ / 41°F to 10℃ / 50°F. The right zone’s temperature setting can be adjusted from 10℃/ 50°F to 18℃/ 64°F.
WALL INSTALLATION GUIDELINES Add on the adjustable feet/bumpers to the back of each screw on the rear of the wine cooler. This will ensure that your wine cooler has enough room between it and the wall to properly exhaust. Place the M8 boring crowns against the wall and use them as a guide for where to drill your holes. The diagram above shows the required space between each hole. Use the screws (part B) to affix the boring crowns to the wall.
Attach Part A to the back of the unit. Slide Part A into the boring crowns to affix your unit to the wall. Drip Tray Installation 1. Affix the mount for the drip tray to the bottom of the cooler as shown in the diagram above. 2. Route the water pipe into the drip tray. 3. Place the drip tray into the mount.
Note: Space for the drip tray is limited. For wall installation, we recommend that the water pipe be routed to a separate container. Check your drip tray regularly for condensation and empty as needed to avoid leakage. CARE AND MAINTENANCE Cleaning Your Wine Cooler IMPORTANT: Always unplug the unit before cleaning or performing maintenance. Never use harsh cleansers or scouring pads to clean any part of the unit.
• Ensure that the unit stays securely in the upright position during transportation. Protect the outside of the appliance with a blanket. Energy Saving Tips Locate your wine cooler in the coolest area of your room, away from heat producing appliances and out of direct sunlight. PROBLEMS WITH YOUR WINE COOLER You can solve many common Wine Cooler problems easily, saving you the cost of a possible service call. Try the suggestions below to see if you can solve the problem before calling the servicer.
TERMS AND CONDITIONS Vinotemp International (“Seller”) and the person or entity that acquires these goods from Seller (“Purchaser”) hereby fully agree to the following terms and conditions of the sale: Shipping fees are the responsibility of the Purchaser whether freight prepaid or freight collect.
For Non-New Units (Scratch & Dent/Refurbished/Floor Models), warranty for compressor units is 90 days from your dated invoice and 30 days for thermoelectric units (parts for function only, not cosmetic defects). These units are refurbished and sold as is; Purchaser assumes risks to the quality and performance of goods and assumes the costs of all necessary service or repair not covered herein.