TABLE OF CONTENTS Important Safety Information ........................................................................... 2 Installation Instructions .............................................................................. 3 – 9 Before Using Your Ice Maker .................................................................... 3 Installation of Your Ice Maker .................................................................... 3 Installation Specifications (Built-In) ....................................
IMPORTANT SAFETY INFORMATION READ ALL SAFETY INFORMATION BEFORE USING. WARNING: RISK OF CHILD ENTRAPMENT An empty ice maker is a very dangerous attraction to children. Remove either the gasket, latches, lock and/or doors from unused or discarded appliances, or take some other action to make sure it is harmless. GROUNDING INSTRUCTIONS PRECAUTIONS To avoid installation/operation difficulties, read these instructions thoroughly. WARNING: This appliance must be grounded.
INSTALLATION INSTRUCTIONS BEFORE USING USING YOUR YOUR BEFORE ICE ICE MAKER MAKER INSTALLATION INSTALLATION SPECIFICATIONS SPECIFICATIONS (BUILT-IN) (BUILT-IN) Remove the exterior and interior packaging. Before connecting the Ice Maker to the power source, let it stand upright for approximately 2 hours. This will reduce the possibility of a malfunction in the cooling system from handling during transportation. Clean the interior surface with lukewarm water using a soft cloth.
INSTALLATION INSTRUCTIONS INSTALLATION SPECIFICATIONS (OUTDOOR USE) • Unplug the power cord and release the brake before moving the cabinet. • Do not put any goods on top of the cabinet and avoid slanting the cabinet when moving it. • Push the cabinet from the rear making sure the door does not open. • Please do not use the cabinet in bad weather to avoid short circuits. Position the cabinet under a canopy. • Do not let children climb the cabinet or move the cabinet to another location.
INSTALLATION INSTRUCTIONS To Connect Water Supply Line to Ice Maker Inlet Valve 1. Disconnect Ice Maker from electric power supply. 2. Place end of water supply line into sink or bucket. Turn ON water supply and flush supply line until water is clear, turn OFF water supply at shut off valve. Unscrew plastic cap from water valve inlet and save. 3. Slide brass compression nut, then ferrule (sleeve), onto water supply line, as shown in Fig. A. 4.
Connecting Ice Maker To Water Supply (cont’d): Drain-pipe Connection (Drain hose not provided) If you choose direct drainage or force drainage mode, you need to purchase an external drain pipe available at your local hardware store. The connection instructions are below: Connect one side of the external drain pipe linked to the outlet pipe of the ice maker; put the other side into the drain hole. (See Fig B.
INSTALLATION INSTRUCTIONS Please disconnect unit from power. To avoid electric shock, make sure no water is near the ice maker or on floor board and follow the steps below. Your ice maker has three different performance modes. You can choose the most suitable mode according to your requirements. Please see detailed instructions on following page. 1. Ice bin 2. Bottom board of ice bin 3. Drain nut (front) 4. Drain seal (front) 5. Water level indicator 6. Drain seal (back) 7. Drain nut (back) 8.
INSTALLATION INSTRUCTIONS Ice Maker Performance Mode Instructions (cont’d) Please read the following installation methods before using, and choose the correct drain mode for your situation. Set up your ice maker accordingly. Performance Mode Instructions Suitable situation Operation instruction Direct drainage Excess water The height of drain hole Ref.: Fig. A, Fig. B & Fig.
INSTALLATION INSTRUCTIONS Ice Maker Performance Mode Instructions (cont’d) Performance Mode Instructions Suitable situation Operation instruction Ref.: Fig. A, Fig. B & Fig. C Manual drainage system mode Manually drain the water from the ice bin. There is no drain hole in the room. (If you’re operating using the “Manual drainage system mode”, ice water will restrict drain water from flowing out.
OPERATING INSTRUCTIONS CONTROLS OF THE ICE MAKER Control Type Condition Function Explanation Button Press Button Press To turn the Ice Maker on/off, press and hold this button for approximately 3 seconds. Small size of ice Button Press Medium size of ice Button Press Large size of ice Indicator Light ON FLASHING ON Small size of ice is selected. Water tank is full. ① Medium size of ice is selected. ON FLASHING ON OFF FLASHING Large size of ice is selected. Ice bin is full of ice.
OPERATING INSTRUCTIONS CONTROLLING THE SIZE OF ICE CUBES ICE BIN 1. Please insure the water supply is properly connected. The default setting of the ice maker is set to make medium ice. If you need to revise the ice size, you can press buttons Your ice bin is designed to be easily removed, if you want to take it out, lift up the front part of the bin, then simply pull it out. (See picture below.) The relevant Indicator light will display. 2.
CARE AND MAINTENANCE CLEANING YOUR ICE MAKER MOVING YOUR ICE MAKER Turn off the power, unplug the appliance, and remove all items, including shelves and rack. Wash the inside surfaces with a warm water and baking soda solution. The solution should be about 2 tablespoons of baking soda to a quart of water. Wash the ice bin with a mild detergent solution. Wring excess water out of the sponge or cloth when cleaning area of the controls, or any electrical parts.
CARE AND MAINTENANCE CLEANING THE INNER WATER CONTAINER NOTE: If the unit is unplugged, has lost power, or is turned off, you must wait 3 to 5 minutes before restarting the unit. If you attempt to restart before this time delay, the Ice Maker will not start. Please disconnect unit from power. To avoid electric shock, make sure no water is near the ice maker or on floor board and follow the steps below. 1. Ice maker machine cover board 2. Ice maker machine cover plate 3. Water container 4. Drain tube 1.
TROUBLESHOOTING Occasionally, a problem is minor and a service call may not be necessary. Use this troubleshooting guide for a possible solution. If the unit continues to operate improperly, call an authorized servicer: PROBLEM POSSIBLE CAUSE The Ice Maker does not operate. • Not plugged in. • The appliance is turned off. • No power to unit. • The ambient temperature is too high. • The door is opened too often. • The door is ajar. • The door gasket does not seal properly. • Incorrect mode was set.
NOTES 15
TERMS AND CONDITIONS Vinotemp International Corp. (“Seller”) and the person or entity that acquires these goods from Seller (“Purchaser”) hereby fully agrees to the following terms and conditions of the sale: Shipping fees are the responsibility of the Purchaser whether freight prepaid or freight collect.
Printed in China