User guide

Wine storage system

Each IDR3 or IDR4 kit contains:

10.

11.

1. 6 WS33 or WS43 VintageView

racks (bottles not included)

2. 2 IDR3 or IDR4 Base Uprights,

IDR-BX only contains 1 Upright

3. 4 Leveling Footer pads with 1 nut and 1 washer each,

IDR-BX only contains 2 Footer Pads

4. 6 PCS 1-1/2”X1-1/2” Plastic Endcaps,

IDR-BX contains 3 Endcaps

5. 12 Self-tapping screws

6. 4 ea. 5/16”X 3/4” Nuts, Bolts and Washers

IDR-BX only contains 2 sets

7. 3 Cross Rails (IDR-CR3)

8. 18 PCS #10X1” Bolts with Nuts

9. 2 Sides for IDR-PR (Presentation Rack)

10. 3 #10X1/2’ Bolts with Nuts

11. 42 Plastic Mounting Hole Covers

1. 2 x 12mm Open End Wrench

2. 14mm Open End Wrench

3. #2 Phillips Head Screwdriver

(Drill with adjustable torque clutch recommended)

4. 8mm nut driver (supplied in IDR-AK)

5. Rack Alignment tool (supplied in IDR-AK)

Required Tools

Island Display Rack (IDR)

Assembly Instructions

Each IDR-EC kit contains:

1. 2 WS31 or WS41 VintageView

racks (bottles not

included)

2. 3 End Cap Rails

3. 6 Self-Drilling Screws with Washers

4. 12 Self-Drilling Screws

Wine Master Cellars • 2000 S. Dahlia Street, Unit 300, Denver, CO 80222 • phone: 866.650.1500 • fax: 866.650.1501

Please feel free to contact us regarding the assembly of this product.

1. 2.

PAGE 1
Island Display Rack (IDR) Assembly Instructions Wine storage system Wine Master Cellars • 2000 S. Dahlia Street, Unit 300, Denver, CO 80222 • phone: 866.650.1500 • fax: 866.650.1501 Please feel free to contact us regarding the assembly of this product. Each IDR3 or IDR4 kit contains: 1. 2. 3. 5. 7. 9. 10. 11. 6. 4. 1. 6 WS33 or WS43 VintageView® 2. 2 IDR3 or IDR4 Base Uprights, 8. racks (bottles not included) IDR-BX only contains 1 Upright 5. 12 Self-tapping screws 6. 4 ea.
PAGE 2
IDR Assembly Instructions 1. Assemble Base Uprights 1.1. Lay out all pieces of the IDR rack to ensure all required components were received. 1.2. Thread one nut onto each footer pad stem. 1.3.Place one washer onto each footer pad stem. 1.4 Thread footer pads into bottom of base upright (IDR-B). 2. Attach Cross-rails 2.1. Lay one base upright flat on the ground 2.2.
PAGE 3
IDR Assembly Instructions (cont.) Assembled IDR: Assembled IDR loaded with bottles: WS Rack CR3 5.6. Repeat steps 6.1 through 6.5 alternating between neck and base strips 6. Make Final Adjustments 6.1. Move the IDR into place and adjust the footer pads to level the rack by turning the shaft either clockwise or counterclockwise. 6.2. Lock the footer pads in place by tightening the nut up against the base upright. 6.3. Insert square plastic caps into top of uprights for a finished look. 6.4.