User Manual V40BVCBK V40BVCS3 vintec.
User Manual 2 V40BVCBK V40BVCS3
! Important information that may impact your Manufacturer’s Warranty Adherence to the directions for use in this manual is extremely important for health and safety. Failure to strictly adhere to the requirements in this manual may result in personal injury, property damage and affect your ability to make a claim under the Vintec manufacturer’s warranty provided with your product. Products must be used, installed and operated in accordance with this manual.
WARNING The information in this document is subject to modification without any prior notice. Somes models are available in dedicated countries only. VINTEC offers no guarantee for our Beverage Center if it is being used for any purpose other than that for which it was specifically designed. VINTEC cannot be held responsible for any error in this manual.
• The room for installing the appliance must be at least 1 cubic metre per 8 grams of refrigerant. The refrigerant quantity contained in this appliance is listed above in grams; it is also noted on the Rating Plate of the appliance. It is hazardous for anyone other than an Authorised Service Person to carry out servicing or repairs to this appliance. – WARNING: Keep ventilation openings in the appliance enclosure or in the built-in structure clear of obstruction.
The Beverage Center should be placed where the ambient temperature is between 5ºC to 35ºC. If the ambient temperature is above or below this range, the performance of the unit may be affected. Placing your unit in extreme cold or hot conditions may cause interior temperatures to fluctuate. The ideal range of temperature may not be reached. (See Climate Class at the end of this manual) Grounding instructions The Beverage Center must be grounded in case of an electrical short circuit.
IMPORTANT - THIS SPACER MUST BE ATTACHED TO THE UNIT BEFORE INSTALLATION FOR VENTILATION PURPOSE. FAILURE TO DO SO VOIDS THE WARRANTY TURNING ON YOUR BEVERAGE CENTER Plug in and switch on the unit by pressing on the power button for a few seconds. When you use the Beverage Center for the first time (or restart the Beverage Center after having it shut off for a long time), there will be a few degrees, variance between the temperature you have selected and the one indicated on the LED readout.
Operating Noises To reach the desired temperature settings, VINTEC Beverage Center, like all Beverage Centers operating with compressors and fans, may produce the following types of noises. These noises are normal and may occur as follows: - Gurgling sound - caused by the refrigerant flowing through the appliance’s coils. - Cracking/popping sounds -resulting from the contraction and expansion of the refrigerant gas to produce cold. - Fan operating sound - to circulate the air within the Beverage Center.
TYPES OF REGULATION Please note that, depending on the loading and settings chosen, it takes about 24 hours for the Beverage Center to see the temperature stabilizing. During this time LED seems to move erratically. It is normal and this process occurs whenever the setting is modified and/or whenever a large amount of bottles are added to the unit. TEMPERATURE SETTINGS Important: The LCD displays, by default, the actual internal air temperature.
Internal light In order to reduce energy consumption, this wine cabinet will automatically switch off the LED lights after 10 minutes. If you want the LED light to remain on continuously, this is possible. Please press and hold the "LIGHT" button for 5 seconds, the display will show "LP".After 4 seconds the display will revert back to normal and the light will remain on until manually switched off.
- While holding the door firmly, remove the three lock screws (2) from the lower right hinge module, and remove it.! Fig.1) REVERSIBILITY OF THE - Remove the three lock DOOR screws (4) from the top right hinge and remove the hinge Warning: To avoid accidents during the process of changing the door, we recommend that (3) . (Fig.3) you get assistance. Thehinge glass(5) door is heavy and may cause injury dropped. - Fix the top left at the top left corner with the threeif lock screws (4) . (Fig.
Width 595mm Depth 571mm + 30mm stopper (Total of 601mm) V26 Height 820mm – 830mm (10mm adjustable feet) Width 380mm 2 . Screws 1. Lower hinge (Right) 3 .Door axis Depth 572mm 5. + 30mm stopper (Total of 602mm) 4. Door Top hinge (Right) 6. Hinge Screws V20 7. Top hinge (Left) 8. Decorative nail 9. Lower hinge (Left) Height 810mm11. – 830mm 10. Door limit device Screw (10mm adjustable feet) Width 295 – 300mm Depth 592mm + 30mm stopper 1.
VENT SPECIFICATIONS Front View (V40) Front View Front View (V20) Front View (V26) Cross section Front View (V20) 400mm User Manual V40BVCBK V40BVCS3 13
5. This Vintec Beverage Center is front venting. The cabinet draws air from the front and rear and expels through the grill under the door at the front. If a joinery kick board is being placed in front of the Beverage Center, a grill of at least the same width as the Beverage Center grill and with a minimum airflow allowance of 150cm2 must be installed into the kick board. 6. This unit has a power switch located on the control panel. Power point location is therefore not critical. 7.
Dimension and Installation Guide 615 595 615* 595 10* 593 563 30 10 525 555 820 850 30 10* 555 525 30 30 30 100 Dimensional Beer-Bottle Beverage Centre drawings: V40BVC S3/BK V40BVCBK 10 10 850 820 10 30 Fro nt View 31 Top View Sid e Vi ew Spacer AL-V40BVC SIDE VIEW 555 525 10 Spacer 525 555 820 830 10 * 30 30 615 595 30 10 FRONT VIEW 10 Fr ont Vi ew * Minimum 10mm required whether proud-fit or flush-fit, however 30mm is recommended on the opening edge for easy finger g
10 10 30 Fr on t View Sid e Vi ew Top Vi ew OPERATION ANOMALIES Ensure that there is power to the electrical supply plug by connecting another electrical appliance to it. Check fuse, if any. Make sure that the door is closed properly. If your beverage center appears to be malfunctioning, unplug it and contact your VINTEC’s after sales service. Any intervention on the cold circuit should be performed by a refrigeration technician who should carry out an inspection of the circuit sealing system.
Irrespective of the cause, if you notice either abnormal temperature or humidity levels inside your beverage center, be reassured that only long and frequent exposure to these abnormal conditions can cause a detrimental effect on your beverage. TROUBLESHOOTING GUIDE Common problems may easily be solved, saving you the cost of a possible service call. Please read carefully the instruction manual and revert to troubleshooting guide chart. PROBLEM Beverage center does not operate.
Warranty FOR SALES IN AUSTRALIA AND NEW ZEALAND APPLIANCE: ALL VINTEC/TRANSTHERM This document sets out the terms and conditions of the product warranties for Vintec/Transtherm Appliances. It is an important document. Please keep it with your proof of purchase documents in a safe place for future reference should there be a manufacturing defect in your Appliance. This warranty is in addition to other rights you may have under the Australian Consumer Law.
User Manual V40BVCBK V40BVCS3 19
Service and support In the rare event that your Vintec cabinet does not perform to your satisfaction, contact our dedicated support team: 1800 771 776 concierge@vintecclub.com Vintec. We are part of the Electrolux Family. To add a touch of professional inspiration to your home, visit electrolux.com.au Stay in touch and share your user experience by following us: @vintecclub © 2018 Electrolux Home Products Pty Ltd. ABN 51 004 762 341 VMAN_V40s_BVCS3_BVCBK_Jun18 vintec.
