User Manual V40SGES3 V40SGEBK AL-V40SGE vintec.
User Manual 2 V40SGES3 V40SGEBK AL-V40SGE
! Important information that may impact your Manufacturer’s Warranty Adherence to the directions for use in this manual is extremely important for health and safety. Failure to strictly adhere to the requirements in this manual may result in personal injury, property damage and affect your ability to make a claim under the Vintec manufacturer’s warranty provided with your product. Products must be used, installed and operated in accordance with this manual.
WARNING The information in this document is subject to modification without any prior notice. Some models are available in dedicated countries only. VINTEC offers no guarantee for our wine cellar if it is being used for any purpose other than that for which it was specifically designed. VINTEC cannot be held responsible for any error in this manual.
The room for installing the appliance must be at least 1 cubic metre per 8 grams of refrigerant. The refrigerant quantity contained in this appliance is listed above in grams; it is also noted on the Rating Plate of the appliance. It is hazardous for anyone other than an Authorised Service Person to carry out servicing or repairs to this appliance. – WARNING: Keep ventilation openings in the appliance enclosure or in the built-in structure clear of obstruction.
The wine cellar should be placed where the ambient temperature is between 5ºC to 35ºC. If the ambient temperature is above or below this range, the performance of the unit may be affected. Placing your unit in extreme cold or hot conditions may cause interior temperatures to fluctuate. The ideal range of temperature may not be reached. (See Climate Class at the end of this manual) Grounding instructions The wine cellar must be grounded in case of an electrical short circuit.
Fixing the Back spacer: Compressor run appliances require proper ventilation for proper and longer usage. Your Vintec wine cellar is supplied with a back spacer. Affix the back spacer at the back of the cellar for air circulation and heat evacuation. IMPORTANT - THIS SPACER MUST BE ATTACHED TO THE UNIT BEFORE THE INSTALLATION, FOR VENTILATION PURPOSE.
1. Vintec “Built in” wine cellars are front venting but are not designed to be fully integrated behind a joinery door. 2. Vintec “Built in” wine cellars require 10mm clearance on both sides and top, 30mm clearance at the rear (Back spacer is provided),to facilitate installation, removal, servicing and ventilation. 3. Vintec “Built in” wine cellars draw air from the rear and expels through the metal grid under the door at the front.
INSTALLATION DRAWINGS FOR BUILT IN WINE CELLARS: User Manual V40SGES3 V40SGEBK AL-V40SGE 9
Dimension and Installation Guide 50 Bottle Wine Cabinet Dimensional drawings: V40SGEBK 593 563 10* 30 850 820 30 10* 615* 595 Spacer FRONT VIEW SIDE VIEW 10* 30 Spacer * Minimum 10mm required whether proud-fit or flush-fit, however 30mm is recommended on the opening edge for easy finger grip access when installed flush-fit. 10* NOTE: Illustrations not to scale. All dimensions in millimetres. TOP VIEW For complete installation instructions, please refer to the user manual for this product.
TURNING ON YOUR WINE CELLAR Plug in and switch on the cellar by pressing on the power button for a few seconds. When you use the wine cellar for the first time (or restart the wine cellar after having it shut off for a long time), there will be a few degrees variance between the temperature you have selected and the one indicated on the LED readout. This is normal and it is due to the length of the activation time. Once the wine cellar is running for a few hours everything will stabilize.
LOADING YOUR WINE CELLAR You may load your wine bottles in single or double rows while taking note of the following: if you do not have enough bottles to fill your wine cellar, it is better to distribute the load throughout the wine cellar so as to avoid “all on top” or “all below” type loads. - Do remove or relocate adjustable wooden shelves to accommodate larger type of bottles or increase the capacity of the cellar by stacking the bottles up when necessary.
TYPES OF REGULATION Please note that depending on the loading and settings chosen it takes about 24 hours for the wine cellar to see the temperature stabilising. During this time LED seems to move erratically. It is normal and this process occurs whenever the setting is modified and/or whenever a large amount of bottles are added to the cellar. Single temperature Maturing/Storage wine cellars: AL/S3/BK: V30SG standard regulation V30SGe, V40SGe: electronic regulation, digital display.
TEMPERATURE SETTINGS Important: The LCD displays by default the actual internal air temperature. The temperature settings are pre-set at the factory as follows. In the event of a power interruption, all previous temperature settings are automatically erased and it will revert to the preset temperature settings. Factory preset chart Setting 12 Temperature 12ºC (+/- 2.5ºC) 12 12ºC (+/- 2.
WINE SERVING TEMPERATURE CHART All wines mature at the same temperature, which is a constant temperature set between 12ºC to 14ºC. The below chart is an indicative temperature chart to indicate the best temperature for drinking purposes.
IMPORTANT INFORMATION ABOUT TEMPERATURE Your VINTEC wine cellar has been designed to guarantee optimum conditions for storing and/or serving your wines. Fine wines require long and gentle developments and need specific conditions in which to reach their full potential. All wines mature at the same temperature, which is a constant temperature set between 12ºC to 14ºC. Only the temperature of “dégustation” (wine appreciation) varies according to the type of wines (see “Wine Serving Temperature Chart” above).
Notes: During the refrigerating cycle, heat is given off and disperses through the external surfaces of the wine cellar. Avoid touching the surfaces during those cycles. ADJUSTABLE WOODEN SHELVES Adjusting/removing the shelves For easy access to the storage content, you must pull the shelves approximately 1/3 of its depth out of the rail compartment. These wine cabinets, however, are designed with a notch on each side of the shelf tracks to prevent bottles from falling.
V40 AL models (30mm recess plinth) 1 Lock screws 4 Top hinge (Right) 7 Top hinge (Left) 2 Lower hinge (Right) 5 Door 8 Lower hinge (Left) 3 Door axis 6 Cabinet body - Unscrew the lock screws (1); (Fig. 1) to remove the door axis located at the bottom. - While holding the door firmly, pull the door (5) outward and take it out; (Fig. 2) - Remove the 3 bolts and take out the right top hinge (2); (Fig. 3) - Fix the left top hinge and the bottom left hinge with the bolts as per Fig.
V40 S3/BK models 1. Lower hinge (right) 4. Door 7. Top hinge (left) 10. Door limit device 2. Screws 5. Top hinge (right) 8. Hole covers 11. Screw 3. Door axis 6. Hinge screws 9. Lower hinge (left) 1. Open the door to a 90 degrees angle, take out the 2 screws (2) from lower door axis (3), remove the door (4), Remove the axis plate (3) from the door, (Fig. A). 2. Unscrew the screw (11) located underneath the doorframe and the limit device (10), and relocate it at left end side of the door frame. (Fig.
OPERATION ANOMALIES Ensure that there is power to the electrical supply plug by connecting another electrical appliance to it. Check fuse, if any. Make sure that the door is closed properly. If your wine cellar appears to be malfunctioning, unplug it and contact your VINTEC’s after sales service. Any intervention on the cold circuit should be performed by a refrigeration technician who should carry out an inspection of the circuit sealing system.
TROUBLESHOOTING GUIDE Common problems may easily be solved, saving you the cost of a possible service call. Please read carefully the instruction manual and revert to troubleshooting guide chart. PROBLEM Wine cellar does not operate. Wine cellar is not cold enough. Turns on and off frequently. The light does not work. Vibrations. The Wine cellar seems to make too much noise. The door will not close properly. POSSIBLE CAUSE Not plugged in. The appliance is turned off.
Warranty FOR SALES IN AUSTRALIA AND NEW ZEALAND APPLIANCE: ALL VINTEC/TRANSTHERM This document sets out the terms and conditions of the product warranties for Vintec/Transtherm Appliances. It is an important document. Please keep it with your proof of purchase documents in a safe place for future reference should there be a manufacturing defect in your Appliance. This warranty is in addition to other rights you may have under the Australian Consumer Law.
User Manual V40SGES3 V40SGEBK AL-V40SGE 23
Service and support In the rare event that your Vintec cabinet does not perform to your satisfaction, contact our dedicated support team: 1800 771 776 concierge@vintecclub.com Vintec. We are part of the Electrolux Family. To add a touch of professional inspiration to your home, visit electrolux.com.au Stay in touch and share your user experience by following us: @vintecclub © 2018 Electrolux Home Products Pty Ltd. ABN 51 004 762 341 VMAN_V40s_SGE_ Jun18 vintec.
