Installation Fusion Virtual Reality FVR Box Installation Guide Part No. V4078-0001 EN www.vintenradamec.
Copyright © 2012 All rights reserved. Original Instructions: English All rights reserved throughout the world. No part of this document may be stored in a retrieval system, transmitted, copied or reproduced in any way, including, but not limited to, photocopy, photograph, magnetic or other record without the prior agreement and permission in writing of the Vitec Group plc. Disclaimer The information contained in this manual is believed to be correct at the time of printing.
Contents Safety & Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 About this Manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Components and Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Front View . . . . . . . . . . . . . . . . . . . . . . . . . . .
Safety & Warnings Important information on the safe installation and operation of this product. Read this information before operating the product. For your personal safety, read these instructions. Do not operate the product if you do not understand how to use it safely. Save these instructions for future reference Warning Symbols Used in these Instructions Safety warnings and cautions are included in these instructions.
Safety & Warnings CAUTION! All connections to other devices must be made using shielded cables. CAUTION! We recommend that you use the power supply cable supplied with the product. WARNING! Always ensure that all power and auxiliary communications cables are routed so that they do not present any danger to personnel. Take care when routing cables in areas where robotic equipment is in use. Water, moisture and dust CAUTION! Using alternative power sources will invalidate the system EMC liability.
Safety and About this Manual Maintenance WARNING! The fitting of non-approved parts and accessories, or the carrying out of non-approved alterations or servicing can be dangerous and could affect the safety of the product. It may also invalidate the terms and conditions of the product warranty.
Components and Connections Front View 2 1 8 1 2 3 4 5 6 7 8 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12V OUT connector . . . . . . . . . . . . . . . . . 12V IN connector (from FVR PSU) . . . . . . . . . . . . . . . . . . . . . . . . . Lens Encoder connector . . . . . . . . . . . . . . . . . . . . . Network connector (reserved) . . . . . . . . . . . . . . . . . . . . . . . . . . Head mounting bracket . . . . . . . . . . . . . . . . . . . . . . . . . . . . Plastic blanking plug . . . .
Components and Connections Rear View 9 10 11 20 19 18 12 13 17 16 6 14 15 9 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Reset button 10 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Genlock LED 11. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . TXD line LED 12 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . Cable clamp 13 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12V present LED 14 . . . . . . . . . . . .
Installation Box Contents and Tools Required 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . FVR Box 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VR Interface Cable 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . RS232 null modem cable 4 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . USB memory stick 5 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Installation Mounting the FVR Box WARNING! Heavy 24.5kg (54lbs). Do not lift the head by the cradle. Two person lift may be required. 2 24.5 kg 54lbs To mount the FVR box to a Fusion head, any fitted payload must be removed and it must be dismounted from its support. All work should be carried out in a workshop environment on a suitable work surface.
Installation Power Options 3 HEAD POWER SOURCE POWER CONTROL DC OUTPUT FH-100 VR FH-100 VR FHR-120 VR AC power via FVR PSU Power on/off switch on the FVR box Enabled DC power from the head via the VR interface cable Power on/off switch on the head Not available CAUTION! Using alternative power sources will invalidate the system EMC liability. FHR-120 VR 8 VR data On completion, mount the head back on to its support, together with the camera and other accessories.
Installation Connecting the FVR Box Genlock I/O Connections Rear Genlock Source Front 10
Installation Head Connections Pedestal Connections FHR-120 VR 8 VR data FP-188 VR FPH-188 VR VR data FH-100 VR FVR QUATTRO SE 11
Installation User Interface Connections Studio VR Connection Studio VR graphics system PSU Connection (FH-100 VR Only) Lens Encoder Connection 12
Installation VR Data Port Pin Designations. Powering Up The VR Data port transmits the VR data to the studio VR graphics system. The RS422 pin designations are as follows: Before powering up the FVR box, ensure that all external cable connections have been secured correctly. VR Connector Pin Number Function on VR Connector Function on VR Studio System 2 RXD-/RXA TXD-/TXA 6 RXD+/RXB TXD+/TXB 3 TXD-/TXA RXD-/RXA 7 TXD+/TXB RXD+/RXB To power up, operate the on/off rocker switch.
Troubleshooting Fault Check The FVR box is switched on but mains, 5V and 12V indicator LEDs are not lit. Check that either a 50–60 Hz AC mains power supply of 100– 240V or a DC power supply of 9.5–28V is connected. Genlock indicator LED is red. Check that the genlock signal from the studio is connected to the Genlock In BNC connector. The genlock signal must be an analogue black burst. The FVR box is switched on, but indicator LEDs on the Quattro SE pedestal are not lit.
Maintenance and General Notices Routine Maintenance Technical Specification The FVR box requires minimal routine maintenance, apart from checking the connections and overall operation periodically. Dimensions Routine checks During use, check the following: • Check cables for signs or wear or damage. Replace as necessary. • Periodically, check the fixings securing the FVR box to the head. • Check that all cables are connected properly. WARNING! Risk of electric shock.
General Notices FCC Certification FCC Declaration of Conformity This product complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: FVR V4078-0001 1.This product may not cause harmful interference. 2.This product must accept any interference received, including interference that may cause undesired operations. FCC Notice This product complies with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.
General Notices European Union Waste of Electrical and Electronic Equipment (WEEE) Directive (2002/96/EC) This symbol marked on the product or its packaging indicates that this product must not be disposed of with general household waste. In some countries or European Community regions separate collection systems have been set up to handle the recycling of electrical and electronic waste products.
Publication part No.