Pan and Tilt Head Operators Guide Vector 750 Vinten Camera Control Solutions
Back Vector 750 Pan and Tilt Head Publication Part No. V4034-4980 Issue 1 (February 2008) Copyright © Vitec Group plc 2008 All rights reserved throughout the world. No part of this document may be stored in a retrieval system, transmitted, copied or reproduced in any way including, but not limited to, photocopy, photograph, magnetic or other record without the prior agreement and permission in writing of Vitec Group plc. Vinten®, Vector® and Quickfix® are registered trademarks of Vitec Group plc.
Back Understanding these instructions English The original instructions presented in this operators guide were written in English, and subsequently translated into other languages. If you are unable to understand these instructions, contact Vinten or your distributor to obtain a translation of the original instructions (EU Countries). БЪЛГАРСКИ Оригиналните инструкции, представени в настоящото ръководство на производителя, бяха написани на английски език, а след това - преведени на други езици.
Back Gaeilge Scríobhadh na treoracha bunaidh don treoirleabhar oibritheora seo as Béarla, agus aistríodh iad go teangacha eile ina dhiaidh sin. Mura bhfuil tú in ann na treoracha seo a thuiscint, téigh i dteagmháil le Vinten nó le do dháileoir, chun aistriúchán de na treoracha bunaidh a fháil (Tíortha an AE). Italiano Le istruzioni originali presentate in questa guida per l'operatore sono in lingua inglese e successivamente tradotte nelle altre lingue.
Back Română Instrucţiunile originale prezentate în acest ghid pentru operatori au fost scrise în limba engleză, şi traduse ulterior în alte limbi. În cazul în care nu înţelegeţi aceste instrucţiuni, contactaţi Vinten sau distribuitorul dumneavoastră pentru a obţine o traducere a instrucţiunilor originale (Ţările UE). Slovensky Pôvodné pokyny, uvedené v tomto návode na obsluhu, boli napísané v anglictine a následne preložené do iných jazykov.
Back Preface Thank you and congratulations on your new Vector 750 from Vinten We want you to get the most from your new Vector 750 and therefore encourage you to read this operators guide to familiarize yourself with its many features, some of which may be new to you. This document also covers essential health and safety information and has a section on maintenance that will ensure you keep your new product in perfect condition.
Back Safety - read this first English—Original Instructions The original instructions presented in this operators guide were written in English, and subsequently translated into other languages. If you are unable to understand any of the translated languages, contact Vinten or your distributor to obtain a translation of the original instructions (EU Countries).
Back Usage The Vector 750 pan and tilt head is designed for use in broadcast and film studios to support and balance a camera and ancillary equipment weighing up to 75 kg (165.3 lb), and must be mounted on equipment designed to support a minimum payload of 95 kg (209 lbs.) The Vector 750 pan and tilt head is intended for use by professional TV broadcast and film camera operators. WARNING! 1. Do NOT attempt to use this product if you do not understand how to operate it. 2.
Back Contents Page Preface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Safety - read this first . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Technical Data. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Usage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Back (1) (2) (13) (3) (12) (11) (4) (5) (6) (10) (7) (9) (8) Fig 1 Vector 750 Pan & Tilt Head (Left-hand Side) (1) Wedge adaptor (2) Wedge adaptor operating lever (3) Wedge adaptor securing screw (4) Pan brake lever (5) Tilt brake lever (6) Carrying handle (7) Level bubble illumination switch (8) Level bubble (9) Pan drag adjustment knob (10) Pan bar clamp (11) Tilt drag adjustment knob (12) Slide plate clamp (13) Slide plate adjustment knob 10
Back (14) (18) (17) (16) (15) Fig 2 Vector 750 Pan & Tilt Head (Right-hand Side) (14) Slide plate (15) Balance adjustment knob (16) Centre lock button (17) Centre lock release catch (18) Pan bar mounting 11
Back (19) (20) Fig 3 Vector 750 Pan & Tilt Head (Underside) (19) Four bolt fixing (20) Bolt hole position indicator 12
Back Introduction The Vector 750 pan and tilt head embodies a unique linkage counterbalancing mechanism, thin film (TF) drag assemblies for pan and tilt motions and an adjustable camera mounting plate. The balance system is easily adjusted by a knob (15) on the right-hand side of the head. The balance adjustment control compensates for differing platform load C of G heights by varying the mechanical advantage of a bell-crank in the counterbalance mechanism.
Back Operation Unpacking The head is supplied with one pan bar and a battery (fitted) for the level bubble illumination unit. A second telescopic pan bar or short pan bar for use with a zoom or focus controller are optional. Ensure that all items are unpacked prior to disposal of the packing materials. After unpacking ensure that: The pan and tilt brakes (4), (5) are on (see Pan and tilt brakes). The centre lock (16) is engaged (see Locking the platform).
Back Fitting a camera WARNING! 1. Do NOT rely on the tilt brake when changing the payload. Always engage the centre lock. 2. Ensure that the weight and C of G height of the total payload is within the range for which the head is designed: up to 75 kg (167.3 lb) with C of G height from 80 mm (3 in) to 250 mm (10 in). To fit a camera, proceed as follows: Lower the mounting to a convenient working height.
Back Ensure that the centre lock is engaged (see Locking the platform) and that the camera and all accessories are fitted. Turn the tilt drag adjustment knob (11) to its minimum setting. WARNING! Increase the balance setting (15) for a heavy out-of-balance payload BEFORE disengaging the centre lock (16), to prevent the platform tipping violently. Holding the pan bar to steady the platform, disengage the centre lock (see Locking the platform).
Back Locking the platform The centre lock mechanism is operated by a button (16) on the right-hand side of the head. To engage the lock, hold the platform in the horizontal position and push the button (16) inwards until it latches and the release catch (17) appears. Use the pan bar to rock the platform slightly whilst pushing the button (16). To release the centre lock, rock the platform slightly and push down on the release catch (17).
Back Servicing General The Vector 750 pan and tilt head is robustly made to high engineering standards and little attention is required to maintain serviceability save regular cleaning. Routine maintenance on the Vector 750 pan and tilt head is limited to annual replacement of the level bubble illumination battery. No further routine maintenance is required. During normal use, check the effectiveness of the platform slide clamp and the adequacy of level bubble illumination.
Back (24) (21) (22) (14) (23) Fig 5 Cleaning the vertical tracks Using a pipe cleaner (or similar) moistened with an isopropanol-based cleaner (3M VBH or similar), and clean the two vertical tracks (24). Upwards pressure on the balance mechanism will allow the area of track under the vertical rollers to be cleaned. Install the platform (22) on the balance mechanism (23) and secure with six screws (21), using Loctite 222E.
Back (25) (26) (15) (2*) (28) (5) Fig 6 Cleaning the horizontal tracks Routine maintenance Level bubble illumination unit battery replacement The level bubble on the Vector 750 pan and tilt head is illuminated by a battery-powered light-emitting diode (LED). A time-delay circuit initiated by a switch controls the LED. The battery should be replaced at yearly intervals or whenever the illumination is considered inadequate.
Back BATTERY TYPE: 9v, 6LR61 (PP3, 6AM6, MN1604, E-BLOCK) Vinten Part No. C550-023 (32) (29) (31) (30) Fig 7 Level bubble illumination unit battery replacement Adjustments After considerable use the platform slide clamp may require adjustment. To enable the payload to be correctly balanced, the wedge adaptor may require repositioning. The pan and tilt brakes may require adjustment after considerable use.
Back (12.1) (12) (12.2) (12.3) Fig 8 Platform slide clamp adjustment Repositioning the wedge adaptor The wedge adaptor (1) is secured by four cap head screws (3) which pass through the wedge adaptor into the slide plate (14).
Back WARNING! Overlong screws will prevent the slide plate from operating. Always use the screws provided (M6 x 30 mm). To reposition the wedge adaptor: Engage the centre lock (see Locking the platform) and remove the load. Hold the body of the wedge adaptor (1) and use a 4 mm hexagon wrench to remove four securing screws (3). Reposition the wedge adaptor (1) on the slide plate (14), ensuring that the narrow end of the wedge adaptor faces forwards.
Back The pan brake is adjusted by turning the pin (4.3). To gain access to the pin it is necessary to remove the payload from the head, remove the head from its mounting and remove a cover plate (4.1) from the underside of the head. To adjust the pan brake, proceed as follows: WARNING! Remove the payload before adjusting the pan brake. Remove the payload from the head. Remove the head from its mounting. On the underside of the head, remove three screws (4.2) securing cover plate (4.1).
Back Parts List The following list includes the main assemblies, user-replaceable spare parts and optional accessories. For further information regarding repair or spare parts, please contact Camera Dynamics Limited or your local Vinten distributor. Item Vector 750 pan and tilt head Wedge adaptor Part No.
Back Warranty Details and Terms and Conditions Please read the Warranty Details and Terms and Conditions below. Register your product to get One Extra Years Warranty and a Free Vinten Quality Gift. Please register now on-line at www.vinten.com/register - it's easy and fast. The product serial number location (25) is shown in Fig 6.
Back UNDER NO CIRCUMSTANCES SHALL VINTEN BE LIABLE FOR ANY SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES, INCLUDING, BUT NOT LIMITED TO, PERSONAL INJURY, PROPERTY DAMAGE, DAMAGE TO OR LOSS OF EQUIPMENT, LOST PROFITS OR REVENUE, COSTS OF RENTING REPLACEMENTS AND OTHER ADDITIONAL EXPENSES, EVEN IF VINTEN HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
